BOSS DC-2W Dimension Chorus Effect Pedal Owner’s Manual

BOSS DC-2W Dimension Chorus Effect Pedal

Before using this unit, carefully read the sections entitled:”USING THE UNIT SAFELY” and “lIMPORTANT NOTES” (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference.

Main Features

• This is a WAZA CRAFT series effect pedal crafted with a high-quality analog original circuit design.
• The “Dimension” effect add unique natural spaciousness and rich depth to your sound.
• This pedal also reproduces the sound of “SDD-320 Dimension D”used by countless recording studios, providing a more sparkling sound.

Panel Descriptions

Precautions When Connecting

• To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
• Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on equipment in the wrong order, you risk causing malfunction or equipment failure. When powering up: Turn on the power to your guitar amp last. When powering down: Tun off the power to your guitar amp first.
• Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

Use of Battery

• The life of the included battery may be limited as its primary purpose was for testing during assembly.
• If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (Supplied on a separate sheet).
• When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible.
• Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.
• If operating this unit on battery, please use alkaline battery.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward. The pedal can be opened without detaching the thumbscrew completely.
2.  Remove the old battery from the battery housing, and remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place the battery inside the battery housing. Be sure to carefully observe the battery’s polarity (+ versus-).
4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.
5. Finally, hold down the pedal while tightening the thumbscrew into the guide bush hole.

OUTPUT Jacks

Specifications

AC adaptor (PSA series: sold separately)

Current Draw| 65 mA

*** Expected battery life under continuous use: Alkaline: 6 hours**

These figures will vary depending on the

actual conditions of use.

Dimensions| 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight| 450 g / 1lb (including battery)
Accessories| Leaflet (“USING THE UNIT SAFELY,”“IMPORTANT

NOTES,” and “Information”)

Alkaline battery (9 V, 6LR61)

Options

(sold separately)

| AC adaptor (PSA-series)

Intellectual Property Right

• Roland, BOSS, and i WAZA CRAFT are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.
• CMSIS-RTOS RTXVersion 4.70.1 Copyright (c) 1999-2009 KEIL, 2009-2015 ARM Germany GmbH All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS”AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

SUPPLIER’S DECLARATION OF CONFORMITY
Compliance Information Statement

• Model Name: DC-2W
• Type of Equipment: Guitar Effects
• Responsible Party: Roland Corporation U.S.
• Address: 5100 S. Eastern Avenue Los Angeles, CA 90040-2938
• Telephone: 323-890-3700

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>