HIKVISION DS-2CD2087G2-LU Pro Series IP Camera Built in Microphone User Guide
- June 6, 2024
- Hikvision
Table of Contents
DS-2CD2087G2-LU Pro Series IP Camera Built in Microphone
Appearance Description
Figure 1-1 Bullet Camera Overview
Table 1-1 Description
No.
|
Description
---|---
1| Lens
2| Camera Body
3| Microphone*
4| Bracket
5| Network Interface
6| Power Interface
7| Reset Button
8| Memory Card Slot
Note:
● Microphone interface varies according to different device models. Please
refer to the actual device.
● Press and hold the reset button about 10s when the camera is powering on or
rebooting to restore the default settings, including the user name, password,
IP address, port No., etc.
Installation
Before you start:
● Make sure the device in the package is in good condition and all the
assembly parts are included.
● The standard power supply is 12 VDC or PoE, please make sure your power
supply matches with your camera.
● Make sure all the related equipment is power-off during the installation.
● Check the specification of the products for the installation environment.
● Make sure that the wall is strong enough to withstand four times the weight
of the camera and the bracket.
For the camera that supports IR, you are required to pay attention to the
following precautions to prevent IR reflection:
● Dust or grease on the dome cover will cause IR reflection. Please do not
remove the dome cover film until the installation is finished. If there is
dust or grease on the dome cover, clean the dome cover with a clean soft cloth
and isopropyl alcohol.
● Make sure that there is no reflective surface too close to the camera lens.
The IR light from the camera may reflect back into the lens causing
reflection.
● The foam ring around the lens must be seated flush against the inner surface
of the bubble to isolate the lens from the IR LEDs. Fasten the dome cover to
the camera body so that the foam ring and the dome cover are attached
seamlessly.
For the camera that supports supplement light, DO NOT stare at the light to
avoid potential injury.
Memory Card Installation
Follow the steps to mount and unmount the memory card.
Steps:
1. Loosen the screws to remove the memory card slot cover.
Figure 2-1 Unscrew the Cover and Insert Memory Card
2. Insert the memory card into the memory card slot.
3. (Optional)To unmount the memory card, push to get it ejected.
4. Screw the cover back to the camera.
Ceiling Mounting
Before you start:
Both wall mounting and ceiling mounting are suitable for the bullet camera.
Ceiling mounting will be taken as an example in this section. And you can take
steps of ceiling mounting as a reference for wall mounting.
Steps:
1. Paste the drill template (supplied) to the desired mounting position on
the ceiling.
2. Drill the screw holes in the ceiling according to the supplied drill
template.
Note:
Drill the cable hole, if adopting ceiling outlet to route the cable.
3. Route the cables through the cable hole (optional), or the side opening.
4. Fix the camera on the ceiling with supplied screws.
Note:
- In the supplied screw package, both self-tapping screws, and expansion bolts are contained.
- If the ceiling is cement, expansion bolts are required to fix the camera. If the ceiling is wooden, self-tapping screws are required.
5. Connect the cables and power on the camera to view the live view image.
6. Adjust the surveillance angle.
- Loosen the No.1 adjusting screw to adjust the rotation position [0° to 360°].
- Tighten the No.1 adjusting screw.
- Loosen the No.2 adjusting screw to adjust the tilting position [0° to 90°].
- Tighten the No. 2 adjusting screw.
- Loosen the No.3 adjusting screw to adjust the pan position [0° to 360°].
- Tighten the No.3 adjusting screw.
7. (Optional) Install the waterproof jacket. Refer to 2.4 Waterproof Measures for details.
Wall Mounting with Junction Box Before you start:
Before you start:
- Both wall mounting and ceiling mounting are suitable for the bullet camera. Wall mounting will be taken as an example in this section. And you can take steps of wall mounting as a reference for ceiling mounting.
- The junction box is not included in the package. You need to prepare one for this mounting type
Steps:
1. Paste the drill template (supplied) to the desired mounting position on
the wall.
2. Drill the screw holes and the cable hole (optional) in the wall according
to the drill template.
Note:
Drill the cable hole, if adopting a ceiling outlet to route the cable.
3. Take apart the junction box, and align the screw holes of the bullet
camera with those on the junction box’s cover.
4. Fix the camera on the junction box’s cover with three PM4 × 10 screws.
Figure 2-6 Fix the Camera on Junction Box’s Cover
5. Secure the junction box’s body with three supplied screws on the wall.
6. Route the cables through the cable hole. Here we take the bottom cable
hole as an example to describe the installation.
1). Separate the waterproof cover and the cable gland from the junction box.
2). Route the cable through the bottom cable hole and the cable gland.
3). Screw the cable gland back on the bottom cable hole.
4). Screw the waterproof cover back on the side cable hole.
7. Combine the junction box cover with its body with three screws on the
junction box’s cover.
8. Repeat steps 5 to 7 of 2.2 Ceiling Mounting to complete the installation.
Waterproof Measure
If the camera is installed outdoor, you should use the waterproof accessory or tapes to waterproof the cables. Otherwise, the cables might get wet or a short circuit occurs.
Steps:
1. Feed the network cable through ① and ③ in order.
2. Fix ② on the network cable between ① and ③.
3. Place ⑤ onto the end of ⑥, and plug the RJ45 male connector into RJ45
female connector.
4. Screw ③ to ⑥ clockwise
5. Push ② into ③.
6. Secure ① with the ③ in clockwise direction.
Waterproof Other Cables
After routing and connecting the cables, use the waterproof tapes to wrap up the cables. Connected cables and spare cables both should be wrapped up as the figures below.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>