hama 179809 Replacement Remote Control GRUNDIG TVs Instruction Manual

GRUNDIG TVs
Replacement Remote Control
Operating Instructions

Replacement Remote for PANASONIC SERIES: TV/LCD/LED/HDTV

Thank you for your decision on the Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for futurereference.
This remote control can by default control 90% of models of the PANASONIC brand, there´s no need to set it up. lf the remote doesn‘t work, please choose one of the setup methods described in chapter 5.

The keys

1. Power TV ON/OFF –LED-Indicator
2. Numeric keys for channel selection
3. Favorit List
4. Select On-Screen Options
5. Exit Menu
6. Programm information
7. Enter Menu| 8. Select Menu Options
9. TV settings
10. Volume settings
11. TV Mute
12. Previous (DVD, BlueRay…)
13. Next (DVD, BlueRay…)
14. Record(DVD, BlueRay…)
---|---
15. Play (DVD, BlueRay…)
16. 3D Mode
17. ShareScreen Options
18. Media Player Menu
19. Language selection
20. Language selection subtitles
21. Pause (DVD, BlueRay…)
22. Stop (DVD, BlueRay…)
23. Fast backward(DVD, BlueRay …)| 24. Fast forward(DVD, BlueRay…)
25. Programm Selection
26. Source selction
27. Open electronic program guide
(if supported by the TV)
28. Confirm selection
29. Back key
30. Streaming app menu
31. Teletext ON/OFF

Explanation of the Note and Warning symbol

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• Replacement Remote Control
• 2x AAA Batteries
• These operating instructions incl. Code List

Sicherheitshinweise

• Do not use the remote control in moist or wet environments and avoid spray water contact.
• Do not expose the remote control to heat sources or direct sunlight.
• Do not drop the remote control.
• Never open the remote control. It contains no user-serviceable parts.
• As with all electrical devices, keep the remote control away from children.

Warning

• When inserting batteries note the correct polarity (+ and -markings) and insert the batteries accordingly. Failuretodosocould results in the batteries leaking or exploding.
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a fire.
• Keep batteries out of the reach of children.
• Do not allow children to change batteries without supervision.
• Remove the batteries from products that are not being used for an extended period.

Getting started –Installing the Batteries

Note

• Use 2AAA batteries
• Remove the battery cover from the bottom of the remote.
• Check the +/- polarity on the batteries and inside the compartment.
• Insert the batteries.
• Slide the battery holder back into the remote until the clips locate.

Note –Code Memory

• This remote control saves the settings during battery change.

Setup

This remote control can by default control 90% of models of PANASONIC brand, there´s no need to set it up. lf it doesn‘t work, please choose one of the following setup methods 5.1 or 5.2.

DIRECT CODE ENTRY CODE List:

001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013, 014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026, 027, 028, 029, 030, 031, 032, 033, 034, 035, 036, 037, 038, 039, 040, 041, 042, 043, 044, 045, 046, 047, 048, 049, 050, 051, 052, 053, 054

1. Press and hold the [MUTE] &[POWER] keys for approx. 3seconds until the LED will be lit.
2. Enter the corresponding 3-digit codes from the code list using the digit keys. The LED indicator confirms each entered digit by a short flash and turns off after 3valid digits. Otherwise, the LED will flash 3times and then remain on for re-entry.
3. Please try to use the remote control.If it doesn‘t work well, please try other codes: [002], [003], [004] …

Note

• No entry for approx. 15 seconds will time out the set-up mode.
• If the code is invalid, the LED flashes 3times and then lights up permanently.
• To exit the setup, please press the [MUTE] key.

MANUAL CODE SEARCH

1. Press and hold [MUTE] and [POWER] keys for approx. 3seconds until the LED will be lit.
2. Press and release [P+] or [P-] key to start searching the code. Each time you press, the remote will change to the next code.
3. Please test if the [POWER], [VOL+], [MENU], [0-9] keys work well. If ok, please press the [MUTE] key to save the code and exit.
4. If it doesn‘t work well, repeat the fast search by pressing the [P+] or [P-] key.

Note

• At the set-up mode, only the [POWER], [VOL+], [MENU], [0-9] keys are working.

CODE INQUIRY

Use the following method to find out which code is currently set:

1. Press and hold [MUTE] and [POWER] keys for approx. 3seconds until the LED will be lit.
2.  Enter the code [9] [9] [0] (The LED will flash once for each enter) with the number keys. The LED will flash twice and goes off.
3. Press the key [1] for the 1st digit of the code. The LED will start to flash. Count the LED flashes. The number of flashes resembles the code‘s first digit.
   Repeat this procedure for the 2nd and 3rddigit of the code:
   2nd digit -> press the key [2] -> count LED flashes
   3rddigit -> press the key [3] -> count LED flashes
   If the code number is 0the LED will not flash. After the LED has indicated the third digit it will turn off.

Compatible Remote Control Model

Due to too many remote control models, we only Iist some of them below. lf your remote control is similar to the drawing, the replacement remote can control your TV (Page 47).

LEARN MODE

This remote control is equipped with a learning function. Thus, you could learn the functions of your original remote to this remote control.

BEFORE STARTING TO LEARN MODE

• The batteries in the two remote controls have to be in good condition. Replace them if necessary.
• Place the remote controls with the infrared diodes so that they point towards each other.
• Where necessary adjust the height of both remotes so that infrared diodes are properly aligned.
• The distance between the remote controls should be about 3cm.

Note

• Do not move the remote controls during the learning procedure.
• Ensure that the room is not lit by fluorescent tubes or low energy consumption lamps since such light sources could interferewith the copying.
• The 2remotecontrols must be at least 1meter away from any light source.
• During learning mode, if no key is selected for more than 15 seconds, the learning mode will exit automatically or if no other remote signal is received.
• Each function key will hold only one command. The new command to be learned will automatically replace the previous one.

ENTER LEARN MODE

1. Press and hold the [MUTE] and [VOL+] keys for approx. 3seconds until the LED will be lit.
2. Enter the code [9] [8] [0], the LED will flash 2times and then remain on.
3. The remote control is now ready to learn new commands.

LEARNING OF KEYS

1. Press and release the desired key on the original remote control which you want the command to be learned. The LED at your replacement remote will flash to confirm that the information has been received.
2. Then press and release the target key on the remote control you want to be learned.
3. If the LED flashes 3times and then remains on, the command has been learned successfully.
4. Repeat these steps to learn other key functions.
5. Please press the [OK] key to save the code and exit learning mode.

Note

• While replacing the batteries, the remote control will keep the functions of the learned keys.

CLEARING OF LEARNED KEYS

6.4.1 CLEARING OF ONE LEARNED KEY

1. Press and hold [MUTE] and [VOL+] keys for 3seconds until the LED will be lit.
2. Enter the code [9] [8] [1], the LED will flash 2times and then remain on.
3.  Press and release the desired key at the replacement remote control which you want to clear the learned command. If the LED flashes 3times, the learned command has been cleared successfully.

6.4.2 6.4.2 CLEARING OF ALL LEARNED KEYS

1. Press and hold [MUTE] and [VOL+] keys for 3seconds until the LED will be lit.
2. Enter the code [9] [8] [2], the LED will flash 2times and then remain on.
3. Press and release the [OK] key at the replacement remote control. If the LED flashes 3times, all commands have been cleared successfully.

EASY Mode

This remote control is equipped with an Easy Mode. Thus you could reduce the functionality of the remote control to its basic functions. It avoids that the TV Settings are changed by mistake.
During the EASY Mode you still could use the following keys:

| Switch the TV On or Off
Change the volume
Mute the TV
Change the program
Numeric keys for program selection/ direct page selection Teletext
Teletext ON/OFF
---|---
| Select On-Screen Options
Show the Electronic Program Guide (if supported by the TV)
Select signal source
Exit Menu

Enter EASY Mode

1. Press and hold [MUTE] and [SHARE SCREEN] keys for 3seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [OK] key,filed flash 3times, you have entered the EASY Mode successfully.

Exit EASY Mode

1. Press and hold [MUTE] and [SHARE SCREEN] for 3seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [EXIT] key,filed flash 3times, you have exit the EASY Mode.

Note

• While the EASY Mode is activated only the keys are mentioned in chapter 7. will work. If one of these keys is pressed the LED will be lit until the key is released. If one key is pressed during the normal mode, the LED will flash.

Maintenance

• Do not mix new and used batteries for powering the remote control, as old batteries tend to leak and may cause power drain.
• Do not use corrosive or abrasive cleansers on your remote control.
• Keep the remote control dust-free by wiping it with a soft, dry cloth.

Troubleshooting

Q. My Universal remote control does not work at all!
A. Check your TV. If the TV main switch is turned off, your Remote cannot operate your TV.
A. Check whether your batteries are inserted properly and are in the correct +/- position.
A. If the batteries are low, replace the batteries.
Q. My TV responds only to some of the commands.
A. Try other codes until most keys work properly.
Q. Some keys of the remote control do not work anymore?
A. Maybe the EASY Mode had been activated. Deactivate the EASY Mode as explained in chapter 7.2.

Warranty Disclaimer

The manufacturer assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or failure to observe the operating instructions and/or safety notes.

Service and Support

Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here: www.hama.com

Recycling Information

Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices, as well as batteries, must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country.  This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices/Batteries, you are making an important contribution to protecting our environment.

Hama GmbH &CoKG
86652 Monheim/Germany
www.hama.com

All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.

Documents / Resources

| hama 179809 Replacement Remote Control GRUNDIG TVs [pdf] Instruction Manual
179809, Replacement Remote Control GRUNDIG TVs, 179809 Replacement Remote Control GRUNDIG TVs, Remote Control GRUNDIG TVs
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>