hama Shredder Premium M10 Instructions

hama Shredder Premium M10

Operating Instructions

Machine setup

1. Intake shaft for paper and plastic cards
2. Connecting cable (back of the device)
3. Warning symbols
4. Viewing window
5. Pull-out basket
6. Slider switch
7. Castors
8. ” “position (Backwards)
9. ” “position (Off)
10. “|”position (Automatic start /stop function)
11. Status LED: Ready
12. Status LED: Overload
13. Status LED: Overheating

Introduction

Foreword

Thank you for choosing aHama product.
Take your time and read the following instructions and information completely.Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Note –Importance of the operating instructions
Failure to observe the operating instructions when using the product constitutes incorrect use or wilful misuse and is not permitted.

This device is anew,unused product.
Any cutting residue present may have been left over from quality assurance tests during production.

Explanation of warning symbols and notes

• Risk of electric shock
  This symbol indicates arisk of electric shock from touching product parts carrying hazardous voltage.

• Warning
  This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

• Note
  This symbol is used to indicate additional information or important notes.

Package contents

• “Premium M10” shredder
• These operating instructions

Security

Correct use

• This product is intended for the destruction of documents both in the home and in the commercial sector, provided the applications are comparable with typical household use (e.g. in offices, workshops and hotels, etc.).
• Use the product only for the intended purpose.
• The product is intended only for use inside buildings.
• Protect the product from dirt, moisture and overheating and use it in dry rooms only.
• Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
• Do not use the product in a damp environment and avoid splashing water.
• Do not operate the product outside the power limits specified in the technical data.
• Do not operate the product continuously, as it is not designed for this.
• Do not use the product in areas in which electronic products are not permitted.
• Do not drop the product and do not expose it to any major shocks.
• This product is not intended for use by persons, including children, with limited physical, sensory or mental abilities or lacking in experience or knowledge, unless they aresupervised by aperson responsible for their safety or have been instructed on how to use the product.
• As with all electrical products, this device should be kept out of the reach of children.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
• Dispose of packaging material immediately in accordance with the locally applicable regulations.
• Do not modify the product in any way. Doing so voids the warranty.
• Only use the article under moderate climatic conditions.
• Always pull directly on the plug when disconnecting the cable, never on the cable itself.

Note

• The product is only intended for volumes generated by households.
• Any use is permitted only with the paper container provided.
• If the device is used commercially, increased duty of care requirements apply.
• Therefore, please observe the accident prevention regulations of the German employers liability insurance association for electrical systems and equipment. Please also observe all accident prevention regulations from other applicable employers liability insurance associations and accident insurance companies, as well as any legal regulations applicable to the particular industry and/or location.

Basic safety instructions

Please note the following safety instructions in order to use the device safely.

•  Check the device before use for any visible external damage. Do not put damaged device into operation.
•  People who, as a result of their physical, mental or motor capacities, are unable to operate the device safely must only use the device under supervision or after instruction by a responsible person.
•  Faulty components must only be replaced with original spare parts. Only these parts are guaranteed to meet the required safety standards.
•  Protect the device against moisture and the penetration of liquids or objects. In the event of contact with liquid, disconnect the device from the power supply immediately.

Warning -risk of cutting on the cutting rollers

• Do not touch the cutting rollers.
• Do not open the device or continue to operate it if it becomes damaged.
• Do not use the product if the AC adapter, adapter cable or power cable is damaged.
• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
• This device is not intended for use by children.
• Avoid touching the intake opening with hands, clothing or hair.
• Unplug the device if it is not going to be used for a prolonged period.
• Children must be supervised when using the device.
• Do not insert paper clips into the intake shaft.
• Keep clothing away from the intake shaft.
• Keep jewellery,e.g. necklaces, away from the intake shaft.
• Keep hair away from the intake shaft.
• Do not use any aerosol products on or near the device.
• Do not feed CDs/DVDs into the feed shaft.
• Intake shaft for credit cards. Only insert one credit cardata time into the intake shaft for credit cards.

Safety device
The device is equipped with asafety switch and can only be operated if the basket (5) is correctly inserted into the device.

Warning: Any tampering with or modification of the safety features can result in serious injury and is not permitted.

Installation /Setup

•  Only operate the product from asocket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
•  Disconnect the product from the power supply using the On/Off switch –ifthis is not available, unplug the power cordfromthe socket.
•  If using amulti-socket power strip, make surethat the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
•  If you will not be using the product for aprolonged period, disconnect it from mains power.

Note

•  Set the product up on alevel, horizontal and sufficiently stable surface.
•  Route all cables so that thereisnorisk of tripping.
•  Do not bend or crush the cable.
•  Protect the connecting cable from hot surfaces and sharp edges.

Connect the power pack to aproperly installed and easily accessible mains socket.

Operation

Note

• Be awarethat the thickness of paper increases when it is folded, leading to the device’s maximum page capacity being exceeded.
• Always wait until one cutting operation is finished beforestarting the next one.
• Do not use the device continuously for morethan 6minutes at atime.
• Empty the container regularly in order avoid damaging the device.

Switching the device on

•  Move the slider switch (6) to the “|” position (10).
•  The status LED Ready (11) lights up solid green.
•  The device is now ready for use.

Switching the device off: Move the slider switch (6) to the ” “position (9).

Shredding paper:

•  Insert the paper into the centreofthe intake shaft (1). The cutting rollers switch on automatically.
•  Let go of the paper.Once the cutting process is complete, the device switches itself off again.

Shredding plastic cards

•  Insert the plastic card into the centre of the intake shaft (1). The cutting rollers switch on automatically.
•  Let go of the plastic card. Once the cutting process is complete, the device switches itself off again.

Forwards /backwards mod

These modes aredesigned to release any blockages of the cutting mechanism.

• Move the slider switch (6) to the ” “position (8). The rollers on the cutting mechanism now rotate in the reverse direction.
• Move the slider switch (6) alternately to the „|“ (10) and ” ” position (8). Repeat this process around three times.
• Then switch the device off -as described in 4.2 Switching the device off -and disconnect the mains plug.
• Remove the blocked cut material carefully from the intake shaft (1).
• Reconnect the device -as described in 3. Installation/Setup -to the power supply.

Care and Maintenance

Danger –risk of death from electric shock

• Disconnect the mains plug from the socket before starting any cleaning work.
• Do not touch the cutting rollers.
• Ensure, when cleaning, that no moisturepenetrates the device in order to avoid irreparable damage to it.

Emptying the container

•  Switch the device off -asdescribed in 4.2 Switching the device off -and disconnect the mains plug.
•  Pull the basket (5) out.
•  Empty the container.
•  Push the basket (5) back in.
•  Reconnect the device -asdescribed in 3. Installation/Setup -tothe power supply.

Cleaning the device


• Switch the device off -as described in 4.2 Switching the device off -and disconnect the mains plug.
• Clean the device with a dry cloth. In cases of heavy soiling, the cloth can be dampened a little.
• Allow the device to dry completely afterward.
• Reconnect the device -as described in 3. Installation/Setup -to the power supply.

Cleaning /oiling the cutting rollers

• Oil the cutting rollers after each emptying of the waste paper basket in order to prolong the shredder’s service life.
• You can find an appropriate selection of cleaning products at www.hama.com

Troubleshooting

The cutting rollers do not switch on automatically when material to be shredded is inserted.| The slider switch (6) is in the ”  ” position (9).| Move the slider switch (6) to the “ | ” position (10).
The connecting cable

(2) is not connected correctly.

| Ensure that the mains plug is in the mains socket.
The socket is not live.| Check the domestic fuses.
The device is faulty.| Notify Customer Services.
The status LED: Overload

(12) is lit up red.

|

Too much paper has been inserted or it has been drawn in at an angle.

| Switch the device off and allow it to cool down for at least 30 minutes.

Then follow the steps in 4.5 Forwards / Backwards mode.

The device has become too hot.

| Switch the device off and allow it to cool down for at least 50 minutes.

Technical data

*Thicker paper, moisture or any voltage other than that permitted may reduce the performance.

Warranty Disclaimer

All of the technical information, data and instructions regarding operation contained in these operating instructions were up to date at the time of printing and is provided based on previous experience and to the best of our knowledge.
Hama GmbH &CoKG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>