HIF-NICS Portable Entertainment Sound System EB115A V2 User Guide
- June 6, 2024
- HIF-NICS
Table of Contents
HIF-NICS Portable Entertainment Sound System EB115A V2
Please read the owner’s manual completely before using the device. Keep the owner’s manual for later use.
Specifications
Integrated Amplifier Class D Digital
Output Power RMS 300 W
Output Power Max. 600 W
Impedance 4 Ω
Frequency Range 20 Hz – 20 kHz
71 dB
Total Harmonic Distortion <0,2 %
Operating Voltage AC 100 – 240 V, 50/60 Hz
Operating Voltage DC 12 – 15 V
Bass/Mid Loudspeaker 38 cm (15“), 20 Hz – 1 kHz, 4 Ω
Tweeter 3,8 cm (1.5“), 1 KHz – 20 KHz, 6 Ω
Dimensions 450 x 420 x 822 mm
Gross Weight 34 kg
Features
Bluetooth® audio streaming function
TWS function to pair a second EB115AV2 Sound System via Bluetooth Subwoofer
function for operating the EB115AV2 in a vehicle via AUDIO IN input Audio
player (compatible with MP3, WMA, WAV, FLAC, APE)
USB port
SD card slot
Rechargeable battery*
EasyEQ with 5 equalizer presets
Echo audio effect for microphone operation, Karaoke function
Microphone input (6,35 mm)
Guitar Input (6,35 mm)
RCA stereo input
RCA stereo output
3 sturdy handles
4 transport wheels
Device slot on top for tablets
Flange bushing (Ø 35 mm) for P.A. tripod
Up to 21 / 6 / 3 / 1.5 hours runtime at 10 / 20 / 50 / 100% amplifier load
depending on the intensity of the music signal Battery charges during
operation and when the device is turned off
Scope of Delivery
- 1 x Portable Sound System
- 2 x Wireless Microphone (823,85 / 863,3 MHz, 4 x AA Batteries required)
- 1 x Remote (1 x CR2025 button cell included)
- 1 x Power Cable
- 1 x DC 12V Power Connector
- 1 x User’s Manual
Safety Instructions
1. Use only the supplied power cable to pow-er on and charge the built-in
battery. Only supply the device with the voltage specified above.
2. NEVER plug in or unplug the power cord with wet hands. Do not place the
device in a damp place or in the rain to avoid accumula-tion of liquid on the
surface. Do not place a container with water or other liquids on the unit.
3. Do not place heavy objects on the device. Avoid direct sunlight and keep the device away from heat sources such as stoves, radiators, etc. Avoid exposing the device to high levels of dust and dirt, high tempera-tures and strong light and magnetic sources.
4. Do not unplug the connected power cord by the cable directly from the device or the power outlet, always pull directly on the plugs. Keep the power cord away from places where it could be kicked, pinched, or tripped over. Do not lay heavy objects on the cable.
5. Do not disassemble the device. Touching internal parts of the device may result in a serious electric shock. Do not drop metal parts or liquids into the device openings.
6. If the device will not be used for a long time, always disconnect the power plug from the power socket.
Connection Diagram
Functional Overview
-
The LCD display shows status information.
-
Use the MODE button to select the input signal source (BT / USB/SD / Audio In).
-
Insert a suitable memory card with music files into the SD card slot.
-
Insert a USB stick with music files into the USB port.
-
You can play or pause the selected track with the > II button.
-
Use the I<< button to jump to the previous track.
-
Use the >>I button to jump to the next track.
-
Repeat function (RPT):
All > One > Random > Folder
(SD card and USB only) -
The TWS function is used to couple two EB115AV2 systems via Bluetooth® to form a stereo system. Both systems must be in Bluetooth® mode. Then connect your mobile device to one of the systems. To pair, briefly press TWS on the device with which your Blue-tooth® device has connected. Both systems couple within 1 minute. To release the coupled systems, hold the TWS button for approx. 15 seconds.
-
At the signal input AUX (3.5 mm jack) you can e.g. connect a smartphone.
-
At the signal input AUDIO IN (RCA) you can use an external signal source such as a CD player. For subwoofer operation in the vehicle, the RCA cable that comes from the head unit must be connected.
-
At the signal output AUDIO OUT (RCA) you can e. g. connect a mixer.
-
You can connect a microphone to the MIC input (6.35 mm jack).
-
You can connect a guitar to the GUITAR signal input (6.35 mm jack).
-
The MAIN VOL control regulates the overall volume of the sound system.
-
The TREBLE control regulates the treble of the sound system.
-
The BASS control regulates the bass of the sound system.
-
The MIC ECHO control regulates the degree of the echo effect of the connected microphone.
-
The MIC VOL control regulates the volume of the connected microphone
-
The GT VOLUME control regulates the volume of the connected guitar
-
The VOICE PRIORITY switch activates the karaoke function, i.e. the background music will be played a bit quieter as soon as a microphone is used
-
The AUDIO IN GAIN control regulates the input sensitivity of the connected input signal from AUDIO IN.
-
The LPF control regulates the crossover frequency of the AUDIO IN low pass filter.
-
At the LPF / FULL switch, you can determine whether the input signal should be a full-range signal or a low-pass signal (subwoofer mode).
-
The CHARGE button does the following:I: The device is operated with 230 volts via the connected power plug and the internal battery is charged.O: The device is off and the internal battery is charged when the power plug is connected.
II: The device is operated with the internal battery or, if an external battery is connected to DC12V, operated with this.26. Connect the enclosed power plug to POWER. -
This connector is removable and can remain in the vehicle in subwoofer mode. An external 12 volt battery (e.g. vehicle battery) can be connected to DC 12V IN to supply the device with power. Pay attention to correct polarity.
-
The REM control signal (or a switched + 12V supply line) of the car radio must be present at the REM terminal in subwoofer mode.
-
The device fuse (FUSE 30A) protects the device against overload and short circuits. If this is defec-tive, you can usee the spare fuse instead (SPARE FUSE). Exchange defective fuses only for fuses with the same fuse rating and design.
-
The LEDs at BATT show the following:
FULL: The internal battery is fully loaded
LOW: The charging capacity of the internal battery is too low and should
be charged.
CHARGE: The internal battery is being charged.
Functional Overview
Point the remote at the front of the device. The IR sensor is located
approximately in the middle there.
-
Stand-by mode on or off
-
Use the MODE button to select the input signal source (BT / USB/SD / Audio In).
-
Mute on or off With the EQ button you can select five different
EasyEQ equalizer settings (only adjustable by remote control):
Flat: No adjustment
Party: Ideal for parties and large rooms Groove: Ideal for background music BigBand: Ideal for classical/jazz
Studio: Ideal for sophisticated music -
With the U/SD key you can choose between the data carriers USB and SD card.
-
The VOL+ button switches the volume of the cur-rently selected input source one level up each time the button is pressed.
-
The VOL– button switches the volume of the cur-rently selected input source one level down each time the button is pressed.
-
You can play or pause the selected track with the> II button.
-
Use the I<< button to jump to the previous track.
-
Use the >>I button to jump to the next track.
-
Repeat function (RPT): All > One > Random > Folder(SD card and USB only)
-
Title selection via number buttons.
Bluetooth® Audio Streaming
- Turn on the power of the sound system and press the MODE key at the LCD display or the remote until the device confirms Bluetooth as input source acoustically.
- Search the name “HIFONICS” on your mobile phone or an other device and tap on connect. The device confirms acoustically when the connection is succeeded.
- Play music on your mobile phone or an other device and it will be played via the sound system.
- To disconnect the Bluetooth® operation, turn off Bluetooth® on your mobile phone or an other device or change the input source on the sound system.
Wireless Microphones
The two enclosed wireless microphones each require an AA battery, which is not
included in the delivery.
After you have inserted the batteries and pressed the on/off switch on the
microphone, it is ready for use and automatically connected to the sound
system.
After using the microphones, they should be switched off again, otherwise the
inserted bat-tery discharges.
The UHF transmission range of the microphones is 823,85 / 863,3 MHz.
Notes on Disposal of the Internal Battery
According to the Battery Act (BattG), we are obliged to point out the
following: Bat-teries must not be disposed in the household waste. Used
batteries may contain harmful substances which, if not properly stored or
disposed, could damage the environment or your health. But batteries also
contain important raw materials such as iron, zinc, manganese or nickel and
can be recycled.
In the event of a defect, please dispose of the internal battery only at
appropriate battery disposal facilities or recycling centers in your area.
Audio Design GmbH
Am Breilingsweg 3 · D-76709 Kronau/Germany Tel. +49 7253 – 9465-0 · Fax +49
7253 – 946510 www.audiodesign.de –
www.hifonics.de
© Audio Design GmbH, All Rights Reserved
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>