Honeywell H-Class Peel & Present Instruction Manual
- June 6, 2024
- Honeywell
Table of Contents
92-2422-01 Rev.B
Peel & Present Option
Overview
This document describes the contents, installation, and use of the Peel &
Present option for the H-Class printer. After verifying the contents of the
kit and the tools needed, follow the steps below to install and begin using
the option. A maintenance procedure is also included, so keep this
documentation for future
reference.
CAUTION For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.
Contents of the Peel & Present Option
This kit contains the following item:
- Peel & Present Assembly
Tools Required
To install this option, you will need a standard screwdriver.
Step 1: Preparing the Printer
A) Turn ‘Off’ the Power Switch and unplug the power cord from the AC Receptacle.
B) Press down on the Catch, then pull forward to remove the Door.
C) Raise the Access Cover and remove your media from the printer.
D) Remove the Thumbscrew and Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)
Step 2: Installing the Peel & Present Assembly
A) Carefully press the Peel & Present **Assembly into the Front Plate Connector**.
B) Tighten the Mounting Screw to secure the Peel & Present Assembly to the printer.
Step 3: Using the Option
During operation, labels will be peeled from the backing material and dispensed “on-demand” – that is, subsequent printing will occur only after a previously printed label has been removed from the printer. As a reminder, “REMOVE LABEL” will be displayed to prompt you when a label awaits removal.
Begin using the option as follows:
A) Load Media (see the Operator’s Manual for details). Extend 20 inches (50 cm) of Media from the printer.
B) Remove the labels from this extended portion of media, leaving only the Backing Material. Crease the leading edge of this Backing Material and route it behind the Present Sensor (on the Peel & Present Assembly).
C) Route the Backing Material under the Assist Roller and the Internal Rewinder.
D) Wrap the Backing Material in a counterclockwise direction around
the Rewinder Hub and insert the creased leading edge into one of its
Slots. Insert the
Media Clasp (Item**6**
) into the Slot over the creased leading
edge of the Backing Material and around the Rewinder Hub.
E) Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.
F) Ensure that READY is displayed on the Front Panel then press the FEED Key, and proceed according to your observations:
- If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
- If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”
Notes: (1) The operation of the Present Sensor on this option can
also be controlled by host software commands, so ensure that your labeling
program is properly configured for use when sending label formats to the
printer.
(2) If this option is removed with power applied, the printer will behave
as if a label awaits removal; to restore normal operation, cycle power to the
printer.
Step 4: Configuring the Printer
While the Peel & Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:
Note: In the following procedure, consult the Operator’s Manual for detailed front panel instructions.
A) Press the MENU button on the printer’s front panel.
B) Using the DOWN Button, scroll to PRINTER OPTIONS then press
the Right Button.
C) Using the DOWN Button, scroll to PRESENT SENSOR then press the
ENTER Key.
D) Using the DOWN Button, scroll to MODE then press the ENTER Key.
E) Using the DOWN Button, scroll to AUTO then press the ENTER Key.
F) Press the EXIT Key then, at the SAVE CHANGES? prompt, select
YES to complete the installation.
G) Turn the Power Switch ‘Off and ‘On’ to reset the printer and
complete the configuration.
** Note:** If the printer fails to separate the labels from the backing material, the Internal Rewinder may need to be enabled. Using the procedure above as a guide, press the MENU Button, scroll to PRINTER OPTIONS, then to REWINDER, and select AUTO. Afterward, press the EXIT key and save your changes when prompted.
Maintaining the Peel & Present Assembly
To ensure trouble-free operation, the Peel & Present Assembly should be
cleaned after every 100,000 inches (254,000 cm) of media use. This interval
depends on the label adhesive, where “gummy” adhesives may require more
frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS
→ MEDIA COUNTERS in the printer’s menu system.) Clean the assembly as follows:
-
Turn ‘Off’ the Power Switch and unplug the power cord from the AC Receptacle. Raise the Access Cover and remove the media from the printer.
-
Remove the Peel & Present Assembly from the printer.
-
Using compressed air or a soft brush, clean the Sensors.
Note: For cleaning heavy deposits, isopropyl alcohol can be used – provided it is carefully applied using a cotton swab, and then allowed to dry before reconnecting the option to the printer. -
Using a Cotton Swab dampened with isopropyl alcohol, wipe the Peel Edge clean.
-
Reinstall the Peel & Present Assembly onto the printer.
-
Reload media, and close the Access Cover to complete the procedure.
right by our customers.
Documents / Resources
|
Honeywell H-Class Peel &
Present
[pdf] Instruction Manual
Honeywell, H-Class, Peel Present
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>