flic Hub LR Smart Button Starter Kit User Manual
- June 6, 2024
- flic
Table of Contents
Flic Hub LR
Getting started
To get started make sure that you have:
- An active internet connection (Ethernet or WiFi)
- A phone with the Flic App installed
- A Flic button (”Flic”) within Bluetooth range of the Flic Hub LR (”Flic Hub”)
The phone is only necessary during the setup process. Once the setup is complete you no longer need the phone to enjoy Flic!
Power
Connect the Micro USB cable and an external power adapter to the
Flic Hub. The Flic Hub will turn on, indicated by a bright red LED.
After approximately 15 seconds the LED will dim and become discoverable.
Please follow the instructions in the app to complete the initial setup.
We recommend that you use an adapter with at least 1A output. An adapter with
less than the recommended current rating may result in unstable behavior.
Internet connection
To connect the Flic Hub to your WiFi network open the Flic
App and follow the setup steps to get the Flic Hub connected to the internet.
Alternatively, you can simply connect the Flic Hub, via an Ethernet cable. If
the Flic Hub doesn’t have an active internet connection you will not be able
to make use of all the available features. To check if the internet connection
for the Flic Hub is active you should open the Flic Hub settings page in the
app. Look for the network settings section and press test.
Pairing your Flic
To pair a brand new Flic to the Flic Hub, simply tap the ‘+’ button in the
bottom right corner of the Flic Hub app page. After pressing the Flic the
pairing should take a few seconds.
If you are pairing a Flic that was previously paired then you will need to
remove it from that device first. You can do this by navigating to the app page
of the Flic you want to remove, tapping the gear icon, and selecting the
‘Remove’ option. Now you are able to pair this button as described above.
IR accessory setup
Connect your Flic IR
Accessory to the Flic Hub via the 2.5mm connector and place the IR blaster, in
the direction of the receiving device(s).
The range of the IR signal is ~10m. For best results ensure a clear line of
sight between the IR blaster and the receiving device.
To set up your first action, simply select the IR blaster action within the
Flic Hub app page. Follow the app instructions to start recording IR signals
from any of your remotes!
IR accessory mounting
The Flic IR Accessory uses the same reusable adhesive as Flic. Once you have
all your actions set up you can simply peel the label and secure the IR
blaster in the best location to serve all your devices.
If the adhesive starts to lose its stickiness then you can clean it
- Remove it from the IR base and rinse with water.
- Give it a rub and rinse again.
- Leave it to air-dry and it will return to full stickiness.
Do not apply solvents, chemicals, or abrasive cleaning products as this will damage the adhesive.
Audio
Connect any speaker to the Flic Hub via the 3.5mm audio jack
connector.
This allows for the Flic Hub to play sound as feedback to know that a Flic has
been pressed.
Apple HomeKit requirements
The Flic Hub can be configured to forward push events from Flic to HomeKit.
This is done individually for each Flic. Keep in mind that a Flic configured
for HomeKit can not be combined with any other Flic actions.
To get started make sure that you have:
- An active internet connection on the Flic Hub.
- An iOS device with the Flic app installed.
- An active internet connection on the iOS device.
- A Flic is already paired with the Flic Hub.
- A HomePod, Apple TV, or iPad is set up as a home hub.
If you have not already set up HomeKit on your network, then it is recommended that you do so before proceeding with Flic. This can be done using Apple’s Home app.
To control this HomeKit-enabled accessory, the latest version
of iOS or iPadOS is recommended.
Apple HomeKit setup
It is critical that both the Flic Hub and the iOS device have an active internet connection during the setup process
- Using the Flic app, connect to the Fluc Hub and select the Flic that you wish to add to HomeKit.
- In the Flic detail view, there will be a toggle switch called “Add to HomeKit”. Toggle this switch to the on position.
- Before the Flic is added, the Flic Hub itself first needs to be paired with HomeKit. You will be prompted to do so at this point. Follow the in-app instructions.
- Once paired, please continue the setup using Apple’s Home app.
Note: The HomeKit setup process is only necessary the very first time you add a Flic. For any additional Flic that you wish to add, moving the toggle switch to the on-position will automatically share it with HomeKit.
Factory reset
If, for any reason, you must perform a factory reset you need to press the
pinhole button for between 10-15 seconds. By pushing the button, all your
account settings will be lost and the Flic Hub will return to default.
If you remove the Flic Hub from your account and reconnect to it then you will
be prompted to use the Factory Password when pairing. This can be found on the
label on the underside of your Flic Hub.
If during the initial setup you assign your own password and forget this then
you must perform a factory reset to gain access again.
Problems
If you have any issues setting up or using the Flic products that are not answered here, please read FAQ’s at ttps://start.flic.io/faq Alternatively, you can contact us via support@shortcutlabs.com
Compliance
Shortcut Labs declaration of conformity is available at
https://flic.io/doc
For full compliance, list visit
https://flic.io/compliance
Flic 2 is certified as FCC, IC, CE, AUS, R-NZ, and WEEE, RoHS, REACH compliant.
The Flic Hub LR is certified as FCC, IC, CE, AUS, R-NZ, and WEEE, RoHS, REACH
compliant.
Safety usage guidelines
The Flic Hub and Flic are not toys. They contain small parts and accessories
that present a choking hazard. As such they are not suitable for children or
pets.
General
– Do not attempt to service the product.
– Do not use the product in temperatures below -20°C or above +54 °C.
– Clean with a damp cloth only. Do not submerge and do not use chemical or
abrasive cleaning products.
Flic specific
– Battery life will be shortened with heavy usage and/or use in extreme
conditions.
– Flic is not waterproof. Do not submerge or attempt to use underwater as this
will result in irreversible damage that is outside the scope of the Shortcut
Labs AB warranty.
Warranty
Shortcut Labs AB warrants that your Flic hardware product (“the product”) will
be free from defects in materials and workmanship for a period of 24 months
from the date of delivery to the original retail purchaser (“the warranty
period”).
If a defect in the product arises within the warranty period, Shortcut Labs
will, at its sole option and subject to applicable laws: (1) repair or replace
it with a new or refurbished product or component; or (2) refund the original
purchase price upon return of the defective product.
This warranty does not apply to products you purchase from unauthorized
resellers, or where the instructions for use and activation of the product are
not complied with or where the product is damaged as a result of abuse,
accident, odification, moisture, or other causes beyond our reasonable
control.
Note: Battery usage is regarded as normal wear and tear and is therefore
not covered by the 24-month warranty.
For detailed warranty information visit: https://flic.io/documents/warranty-
policy
Notice
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
Caution
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment. This device
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Radio Frequency (RF) Exposure Warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada’s license-exempt RSS. Operation is
subject to the following two conditions:
(1) this device may not cause interference; and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Canada, avis d’Industry Canada (IC)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits. The Wireless Device should be used in
such a manner that the potential for human contact during normal operation is
minimized. This device has also been evaluated and shown compliant with the IC
RF Exposure limits under mobile exposure conditions (antennas are greater than
20cm from a person’s body).
Informations concernant l’exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la
limite d’exposition aux fréquences radio d’Industry Canada (IC). Utilisez
l’appareil de sans fil de façon à minimiser les contacts humains lors du
fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites
d’exposition aux RF d’IC dans des conditions d’exposition à des appareils
mobiles (antennes sont supérieures à 20 cm à partir du corps d’une personne).
Join
us!
https://community.flic.io/
Share your ideas with other Flic users and keep up to date with the latest
news and happenings from the Flic team.
Shortcut Labs AB, Drottning Kristinas Väg 41, 11428, Stockholm, Sweden
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>