LIPPERT LC375994 Adjusting Pitch-All Solera Awings Instruction Manual
- June 6, 2024
- LIPPERT
Table of Contents
Adjusting Pitch-All Solera Awnings
NOTE: The awning will pitch itself to purge the pooling of excess water and may dump a significant amount of water without notice.
- Pitch can be set by adjusting the articulating arm to tip one side of the awning to allow water runoff.
- Extend the awning to the desired position.
- Choose the side of the awning for optimum shade or convenient water runoff. Pull downward on the joint of the articulating arm until the desired pitch is set (Fig. 5) to allow for water runoff. Do not push the joints of the articulating arms up. This will put tension on the gas strut, which can cause the strut to break. Belleville washers and bolts (Fig. 6A) allow the joint to remain in the position set by the operator.
NOTE: The awning can be retracted without resetting the pitch.
NOTE: If the articulating arm does not hold position, it can be tightened
by adjusting the bolt (Fig. 6A) in the center of the articulating arm.
Troubleshooting
Manual override
In the event of power loss or motor failure, the awning can be extended and
retracted manually. Perform the following procedure to manually retract the
awning.
NOTE: This procedure may also be performed to extend or retract the
awning in the event of dry camping or camping without a battery.
-
Remove the rubber grommet (Fig. 7A) from the drive head assembly, exposing the manual override nut on the motor.
NOTE: The drive head assembly is always located on the right side of the awning as it is viewed from outside of the coach. -
Using a 7A6″ socket and cordless/power drill, spin the manual override nut counterclockwise to retract the awning (Fig. 8).
NOTE: A ratchet may also be used to turn the manual override nut. Using a ratchet will take a significant amount of time and should only be used if no cordless/power drill is available.
NOTE: Use caution when retracting the awning manually. The use of a step stool or ladder may be required to completely retract the awning. -
When the awning is completely retracted, remove the socket or drive device and replace the rubber grommet in the drive head assembly.
NOTE: The motor’s internal drive system prevents the awning from moving (extend or retract) on its own. If the motor is damaged or disabled, be sure to secure the awning in the retracted position with a strap around both the outer support arm and the mounted support arm before the manual override nut is released.
CAUTION
During incidents of high wind, heavy rain or extended time away from the unit, it is advisable to retract the awning completely to prevent damage to the awning and the RV.
Maintenance
Resources Required
- 5-gallon bucket
- Clean water
- 1/4 cup of dish soap
Fabric Care
**CAUTION**
Over-spray of cleaning solution can cause eye and sensitive skin irritation. Flush the affected area with clean water and seek medical attention, if necessary. Wear eye protection and appropriate protective clothing to avoid personal injury.
**CAUTION**
Moving parts can pinch, crush or cut. Keep clear and use caution.
If the awning is retracted while wet, extend the awning and let it dry as
soon as conditions allow before retracting. This will help prevent the
formation of mildew and add greatly to the life of the awning.
NOTE: Mildew does not form on the fabric itself, but on the accumulated
dust, dirt and grime. Periodically clean vinyl or woven acrylic fabric using a
mixture of 1/4 cup of dish soap and five gallons of warm water.
- Liberally apply the mixture on the top of the fabric and retract the awning for five minutes. This will apply the mixture to the bottom of the fabric as well.
- Extend the awning and hose off with fresh water.
- Repeat if necessary.
- Allow drying before retracting.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>