CHAPIN 1480 3.5-Gallon Galvanized Steel Handheld Sprayer User Manual

CHAPIN 1480 3.5-Gallon Galvanized Steel Handheld Sprayer

WARNING

WARNING : Improper use or failure to follow instructions can result in explosive failure causing serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions before use with this sprayer as some chemicals may be hazardous when used with this  sprayer.

Parts

| 6-6136 Hose
---|---
| 6-6000 Nozzle
| 6-1866 Shut-off Handle
| 6-3337 Strap
| 3-4843 Fan Nozzle Pack
| 6-7711 Extension wand
---|---
6-1925 Repair Parts Kit Gaskets and Seals (not included)

Note: Your particular sprayer may not include all parts pictured above.

Hose to Tank

Make sure hose is pushed all the way to the tank. Make sure hose clamp is tight and below the hose barb. Turn clockwise with a screwdriver to tighten.

Nozzle

• Attach nozzle to shut-off handle or extension wand.
  

• Insert Filter.
  

• Insert O-ring.
  

• Insert appropriate nozzle into cap.
  

• Attach cap with nozzle to end of housing.
  
  

• Fan spray
  

• Stream spray
  

• Red, Fine spray for finer washes

• Blue, Medium spray for sealers

• Yellow, Course spray for semi- transparent stains

Pre-Use Check

1. Do : Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2. Do : Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before using. Replace with original manufacturer’s parts only.
3. Do : Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4. Do : Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and inspect for leaks).
5.   Do : Direct shut-off away from you and open to make sure discharge is not clogged.
6. Do : If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.
7. Do : Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these conditions are found, replace affected part with original manufacturer’s part  before using.

Filling

1. Do: Turn pump handle counterclockwise and remove pump
2.   Do: Prepare spray solution following all directions and safety warnings on chemical label.
3.   Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4. Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.

Pressurizing and Spraying

• Turn handle clockwise to tighten.Push handle down, turn 1/4 turn counterclockwise to release.
  

• Pump until you feel resistance.
  

• Push handle, down, turn 1/4 turn clockwise to lock. Begin spraying. Re-pump sprayer as required to maintain spray force.
  

Fatigue-Free Spraying

For constant spraying, push down on shut-off handle and move locking mechanism away from you. To release, squeeze handle and move the locking mechanism back towards you.

To Release Pressure

1. Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop turning handle when you hear air escaping.
2. Do: Stay away from the sprayer until all air has escaped.

Care, Storage and Maintenance

1. Do: Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.
2. Do: Open shut-off and allow recommended solvent to run through discharge assembly.
3. Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4.   Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5.   Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.

P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com

References

• Chapin International: Sprayers, Spreaders, Industrial, Irrigation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>