iSecus DT-510 5G Wireless Signal Jammer User Manual

iSecus DT-510 5G Wireless Signal Jammer

Product Information

Specifications

• Model: DT-510
• Type: 5G Wireless Signal Jammer
• User Manual Version: 1.0
• Dimensions: 348mm x 287mm x 62mm
• Weight: 2.6kg
• Power Input: Utility power
• Power Output: 19V 12.63A (240W)
• DC Connector: 5.5mm x 2.5mm

Product Usage Instructions

Installation & Use

• Place the jammer in a suitable location within the area you wish to secure from wireless signals. Ensure the power adapter is connected securely.

Jamming On/Off Quickly

• To quickly turn the jamming function on or off, use the one-button switch located on the device or through the Web control interface.

Indicators

• Refer to the indicator lights to understand the status of the jamming system. Different indicators signify different states of operation.

FAQ

Q: What types of signals can this jammer effectively block?

A: The jammer can effectively block all kinds of wireless signals including 2G, 3 G, 4G, 5G, Wifi (2.4G/5.2G/5.8G), and Bluetooth.

Q: Can I control each channel independently?

A: Yes, each channel can be configured with an independent switch allowing you to control each channel separately.

Overview

Brief Introduction

• Wireless signal jammers can effectively block/jam mobile communication networks 2G/3G/4G/5G and 2.4G/5.2G/5.8G (WIFI/Bluetooth) and other wireless communication signal transmission, including voice, SMS, data uploading/downloading and other services, jamming effect covers the mainstream application bands of the 4 major carriers of China Mobile, China Unicom, China Telecom, and China Broadcasting and Television.
• Other countries and regions can be upgraded through the software to meet their needs.
• Suitable for meeting rooms, examination halls, hospitals, auditoriums, prisons, government agencies, financial institutions and other indoor confidential places.
• The jamming is only for the downlink signal of the base station, which does not affect public information security, and is harmless to other electronic equipment and the human body.

Features

1. Based on SDR (software radio) architecture design and development, using signalling level jamming strategy, from the signal physical layer definition, signal modulation mode and other technical characteristics of the target signal targeted and efficient jamming
2. Low transmit power, high jamming efficiency, compared with traditional jamming technology, in the case of the same transmit power has a better jamming effect and coverage distance
3. Within the coverage area, it can accurately jam the downlink signal of BTS, only jamming with cell phone terminals, without affecting the uplink communication of BTS, especially applicable to the downlink signal jamming of TDD system, without affecting and hindering the safety of public communication.
4. Support 700M-6GHz range of all mainstream mobile communication bands jamming, covering 2G/3G/4G/5G mobile communication and WIFI Bluetooth signals.
5. The system is plug-and-play, with no need for parameter configuration and other additional operations after power-on, easy to use.
6. Support the jamming on/off through the device or Web.
7. Network port connection, support for Web remote monitoring and system parameter adjustment. ( * can support networking applications, optional)
8. Support channel power independent configuration, channel independent switch setting, easy to use and flexible.
9. IP address and other parameters are displayed on the screen.
10. Small size, lightweight, and easy to install.

Appearance

• Dimensions: 348mmx287mmx62mm
• Weight: 2.6kg

Major Accessories

• Input: utility power
• Output: 19 V 12.63A (240W)
• DC connector: 5.5mmx2.5mm

Main Functions and Specifications

1. Effectively jamming all kinds of wireless signals: 2G, 3G, 4G, 5G, Wifi (2.4G/5.2G/5.8G), Bluetooth
2. Power on to work stably for a long time. By default, the jamming is started after power-on
3. With a one-button switch jamming function, the jamming can be controlled through the Web control interface.
4. Each channel can be configured with an independent switch. After the system starts, the channel is on by default.
5. Each channel can be independently configured with power, and the power can be adjusted in 3 levels: high/medium/low
6. Alarm function: The LED indicator alarms. If an abnormal alarm occurs after the system works stably, the alarm indicator is steady red
7. Supports Web remote monitoring and configuration
8. Powered by adapter
9. Antenna: directional (built-in) antenna
10. Power regulation range: high/medium/low 3 adjustable
11. Effective jamming range: Unshielded environment, covering area 60 m²-80m² (RSRP less than -85 dBm ~ -90 dBm)
12. Storage temperature: -40℃~70℃
13. Working temperature: -20℃~40℃
14. Effective jamming frequency bands:

Installation & Use

1. Take out the device mainframe from the packing box.
2. Install the jammer on the standard tripod through the installation screw hole at the bottom, and the best installation height is 1.4m~1.8m.
3. Insert the output port of the power adapter into the host, and then insert the input port of the adapter into the mains socket. After the power is powered on, it starts to start.
4. After the system is powered on, the system enters the automatic configuration state for 4 minutes. when the Alarm and Running indicators are green at the same time, the system turns on the jamming.
5. After the initial configuration of the system, if the warning light indicates red (steady red), power on again to solve the problem.

Jamming On/Off Quickly

1. Power on:
   • Connect the power adapter to the power interface (power on).
2. Observe the indicator lights on:
   • When all the indicators show green at the same time, the jammer officially starts jamming.
3. jamming on:
   • Within the effective range, check the status of the cell phone, can not make a call, can not access the Internet, start successfully.
4. On/Off button switch jamming:
   • After the jammer starts jamming (Alarm/Running indicators are green), you can press the On/Off button to/off jamming from the mainframe or Web control interface:
   • Jamming off (when the jamming is turned off, the Running indicator is steady red), the system status interface shows the system is off.
   • Jamming on (when jamming is activated, the Running indicator is steady green), the system status interface shows the system is working.

Indicators

Indicators When The System Is Working

1. Automatic configuration after system startup:
   • The Running indicator blinks red
2. The system runs normally, and the interference function is enabled:
   • Both the Running indicator and the Alarm indicator are steady green
3. Alarm during system working:
4. The Alarm indicator is steady red, and the Running indicator is steady green
5. On/Off jamming:
6. The Running indicator is steady red, alarm indicator is steady green

Individual Indicator

• A. Alarm indicator steady green: The system works normally
• B. Alarm indicator off: The system is in the startup configuration state
• C. Alarm indicator steady red: The alarm is abnormal
• D. Running indicator steady red: The interference is off
• E. Running indicator blinking red: The system is in the power-on configuration state
• F. Running indicator is steady green: startup jamming state (including startup jamming in some frequency bands)

Notes

1. Ensure that the device is powered on before you log in to the Web control interface.
2. When the wireless signal is jammed, some mobile phones will show a signal icon, which is an illusion, when you make a call, you will find that you can not dial the phone.

Web Control Interface Brief

Log In

1. Ensure that the device is powered on before login, and directly connect the computer to the jammer using the network cable.
2. Jammer’s IP: 192.168.4.*** (shown on screen)
3. Set the IP address of the PC and the IP address of the jammer to the same network segment, for example, 192.168.4.2
4. Login: In the browser, you can directly log in to the system status page using the address on the screen.

System Status Interface

• After successful login, you can directly enter the system status page, as shown in the following figure. You can start/disable jamming with one button.
• If the system status page shows normal operation (green mark), the jamming is started; if the system status page shows the system is closed (gray mark), the jamming is turned off.
• Refresh the web page to get the serial number of the device (The jammer), software version, system temperature, whether the channel is started and the power configuration of the corresponding channel.
• Click the channel switch corresponding to the channel to enable or disable the channel
• Click the corresponding power configuration for a channel to set the power level for the channel
• After the channel switch and power are successfully configured, and then power on again after the power is powered off, all channel switches are on and all power strengths are high by default.

Safety Notice

Before using our wireless signal jamming system, please read the following safety instructions carefully and comply with the code of operation:

1. The user must use the adapter matching the system for the power supply. If other adapters are used, a power supply mismatch may cause damage to the device and the operator.
2. When using the product, strictly refer to the relevant contents of this guide to avoid damage to the human body and the device.
3. The device has been strictly tested and verified before delivery. Do not disassemble the device to avoid damage or abnormal functions.
4. The device has the power transmission function and in some specific cases, the temperature may be high during the system operation, do not touch the device unless necessary. It is recommended to take protective measures during operation (such as wearing gloves).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>