torqeedo Power 48-5000 Battery Switch Instruction Manual

June 11, 2024
torqeedo

Power 48-5000 Battery Switch
Instruction Manual

Power 48-5000 Battery Switch

This installation drawing is an addition to the original operating instructions. Read operating instructions before wiring.
NOTE! When using only one Power 48-5000 battery, the system will be limited to 6kw maximum output.torqeedo Power 48-5000 Battery Switch - fig
1 This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
NOTE! When using only one Power 48-5000 battery, the system will be limited to 6kw maximum output.
Option: One charger for each batterytorqeedo Power 48-5000 Battery
Switch - fig This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
** In case the charger is permanently installed in the boat, the charger housing or its AC PE and battery minus pole must be connected to the common grounding point. The AC connection requires specialist knowledge and may only be carried out by qualified personnel.
If necessary, have the planning and installation carried out by a specialist.
NOTE!** To charge the batteries in the boat, a land connection in the boat with galvanic isolator or isolation transformer is required according to applicable national requirements (e.g. DIN EN ISO 13297, ABYC E-11). torqeedo Power 48-5000 Battery Switch - fig 2Connect the charger housing and the minus battery pole to the common grounding point.
25 mm2 grounding cable System ground connection
This installation drawing is an addition to the original operating instructions. Read operating instructions before wiring. torqeedo Power
48-5000 Battery Switch - fig 3Bus system termination resistor
This installation drawing is an addition to the original operating instructions. Read operating instructions before wiring.

Pos. Item number                    Name Remarks
1 1213340 raise 12.0 EPTorgLink with electronic box
HA. .1. K. L. Cable set with battery switch

picture for cable length
o| | BadcboneTorqiink cable 8-pin| 3000 mm
|
2104 00| Power 48-5000| SelectTorgLink-Battery in throttle menu! NOTEI When using only one Power 48-5000 battery, the system will be limited to 6kw maximum output
a| |
FCable 8-pin  900 mm/50 mm, Do not extend I
not Illus trated| | + Battery pole adapter  Not needed for your configuration
– Battery pole adapter
W| |
System ground| min. 25 mm2, not included
4| 1952-00| ThrottleTopmountTwIn|
22| 000-00858| Gateway|
U| | Gateway Power cable| 1700 mm cable
b| | BackboneTorqiink cable 8-pin| 5000 mm
17| | Emergency switch with cable| 1000 mm
20| | Key switch|
g| |
Cable for key switch 6-Pin to 8-pin| 1000 mm
14| 000-00877| TomUnkTerminator RvIn| Bus termination resistor
a| | T-Cable 8-pin 900 mm/50 mm, Do not extend I
6|
2213-00| Charger Power 48  650W, for AC charging while running use Fast charger Power 48 2212-00; Not compatible with solar charger 2218-00
P| | +
DC charge cable 1300 mm; Do not extend!
CI| | – DC charge cable| 1300 mm; Do not extend!
B+| | + Battery pole| 7,5 Nm
B-| | – Battery pole| 7,5 Nm
AC| | AC power cable| 2000 mm
a| | T- :able 8-pin| 900 mm/50 mm, Do not extend!
Pos.| Item number| Name| Remarks
---|---|---|---
Optional equipment
7| 2212-00| Fast charger Power 48| 2900W
P| | + DC charge cable| 2400 mm; Do not extend!
Q| | DC charge cable| 2400 mm; Do not extend!
Si-| | + Battery pole| 7,5 Nm
B-| | – Battery pole| 7,6 Nm
AC| | AC power cable| 1000 mm
a| | T-Cable 8-pin| 900 mm/50 mm, Do not extend!
8| 2218-00| Solar charge controller for 1 Power 48-5000| ForTorqLink system only! Only as stand alone charger or in combination with 2212-00 Fast charger Power 48!
P| | + Charge cable 1500 mm
Q| | Charge cable 1500 mm
R| | + Input solar cable 150 mm
S| | Input solar cable 150 mm
a| | T-Cable** 8-pin 900 mm/50 mm, Do not extend!

This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
Connect the cruise motor and terminator to each end of the backbone. The TorqLink bus system requires a terminator (terminating resistor) at both ends of the backbone in order to function correctly.
One of the terminators is located in the „Terminator Single“, „Terminator Twin“, „Throttle 1918-00“, „ Throttle 1976-00“ , the other is built into the cruise motor. Therefore, when installing, make sure that the components „Terminator“ and „Cruise motor“ are each connected to one end of the backbone. The connection position of the remaining components on the backbone can be freely selected. Keep the following points in mind when planning:

  • An earthing point is required for your Torqeedo system. Take into account the connection and the cables required for this in your planning. The required cable cross-sections can be found in the section Tools, equipment and material.

  • First determine and plan the installation positions of all components.

  • Measure the required length of the TorqLink backbone.

  • Measure the lengths of all required stub lines (cable connection between component and TorqLink backbone).

  • When planning, please note that TorqLink drop cables must not be extended. If necessary, plan the TorqLink backbone so that the components can be connected through the
    TorqLink drop cable without an extension. If necessary, extend the TorqLink backbone to connect a component that is far away; you can find corresponding extensions in our accessories catalogue.

  • Cables must be fixed every 400 mm, plan attachment material. In places where fastening is not possible, a scuff guard must be fitted.

  • Openly laid cables (e.g. inflatable boat) must be protected with chafing protection, plan sufficient material.

  • When planning, please note not to bundle power cables with data or antenna cables (e.g. radios) for other loads.

  • Observe the minimum bending radius of the cables when planning.

  • If a second earthed onboard power system is available, ensure that both systems use a common earthing point.

  • Live parts must be fitted or installed with protection against accidental contact; the necessary installation space must be taken into account during the planning stage.

  • Always connect batteries as the last component to the system to avoid short circuits and voltage peaks.

  • Do not extend drop cables, extend backbone if necessary.

  • Protect plugs and contacts against contamination before installing them.

  • Do not pull at the cables.

  • Do not twist cables.

  • Do not install cables in permanently wet areas such as bilges.

  • Install cables free of chafing and not around sharp edges, if necessary, attach chafing protection.

  • Maintain bending limits.

  • Install plug connections free of tension and load.

Observe the minimum bending radius when laying all cables:

Torqeedo data cable 8 x diameter
Torqeedo power cable 8 x diameter
Earth cable see cable manufacturer’s specifications
Other power cables see cable manufacturer’s specifications

This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.torqeedo Power 48-5000 Battery
Switch - fig 7 Option: One charger for each batterytorqeedo Power 48-5000 Battery Switch - fig 6

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals