ITSU IS0503A User Manual
- June 6, 2024
- ITSU
Table of Contents
ITSU IS0503A User Manual
Thank you for purchasing the IS0503A. Before operating this unit, please read this manual carefully to ensure optimum performance and safety. This manual should be kept available for future reference.
REMARK: For product improvement, the company reserves the right to change the design and specification at any time without prior notice. Pictures are for reference use only and may differ from the actual product.
SAFETY CAUTIONS
When using this product, basic precautions should always be followed,
including the following:
Please read the instruction carefully before starting to use this product.
Danger - To reduce the risk of electric shock
- Always unplug this product from the electrical outlet immediately after using and before cleaning.
Warning - To reduce the risk of burns, fire, electric shock, or physical injury
- The product should never be left unattended while plugged in. Unplug the product from the outlet when not in use.
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Be sure to use the product only for its intended use as described in this manual. Do not use any attachment not recommended by the manufacturer in order to avoid any danger or accidents.
- Never operate the product if it has a damaged cord or plug, if it is not working properly, if it has been damaged, or dropped into water. Please return the product to the service center of seller for examination and repair.
- Do not carry this product by the supply cord or use the cord as a handle.
- Keep the cord away from hot surfaces or ground.
- Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc.
- Never drop or insert any objects into any openings.
- Do not use or operate outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is thin.
- Before turning the product power off, turn all controls to the off position then remove the plug from the outlet.
- Connect the product to a properly grounded outlet only.
- If the treadmill is foldable, when user finishes using the treadmill, the elevation needs to be back to original position.
- When user is using the treadmill, it can not be folded at the same time.
- Keep a safety space of 2000mm x 1000mm away from the treadmill.
- This machine is only intended for household use.
- For the treadmill with folding function and electric elevation, be sure that the elevation is 0 before folding (To avoid interference of the components).
- Stop using the treadmill if you feel faint, dizzy, or short of breath.
- Wear appropriate exercise clothes when using the treadmill. Do not wear loose clothes that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.
GROUNDING INSTRUCTIONS
The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a path of least resistance for electric current to reduce the risk of electric shock. The product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Danger - Improper connection of the equipment-grounding conductor can
result
in a risk of electric shock. Check with a qualified electrician or serviceman
if you are in doubt as to whether the products are properly grounded. Do not
modify the plug provided with the product if it will not fit the outlet,
have a proper outlet install by a qualified electrician.
The products is for use on nominal 220-240 volt and has a grounding plug that
looks like the plug illustrated in the figure . Make sure that the product is
connected to an outlet having the same configuration as the plug. There is no
need to use any adapter for this product.
Figure Grounding methods
ASSEMBLY INSTRUCTIONS
OPEN THE BOX YOU CAN FIND THE ALL PARTS AS BELOW.
MAIN COMPONENTS:
5# Allen Wrench 5mm 1pcs ; Cross open end wrench 13,14,15 1pcs
Note: Do not insert power until installation is complete.
Take out the treadmill from the carton and place it on a level flat surface. Please always use the aid of a second person when removing the treadmill from the carton
Put the treadmill on the ground, use pull pin fixing the running deck, then use the Allen Wrench(32) to lock Hexagon Socket Button Head Bolt(13), Washer26), Nylon Nut(27) with the Base lengthening tube(5), And then lock the handrail with the Hexagon Socket Button Head Bolt(14) and the Washer(26).
Pull the (48)Fixed knob when putting down the treadmill. When pulling the (48)Fixed knob, you must hold the running platform well and make sure that the running platform is flat on the ground to release your hand.
Will (37) (38), (39) (40) cover fixed in (3) tables and columns (1) joint, with wrench to tighten the screw (21) (74).
OPERATION GUIDE
1.1 DISPLAY PICTURE
1.2 POWER ON
The Treadmill will start at 1.0KM/H after a 3,2,1 countdown.
1.3 PROGRAM
P1-P12 set programs
1.4 SAFETY KEY FUNCTION
When you take off safety key, the LCD will display E07,meanwhile the treadmill
will be stopped. Put the safety key into the safety key hole in the console,
and then the treadmill will be on start/ready status.
1.5 QUICK-START OPERATION
1.5.1 Start/Stop button
Press the START button to begin belt movement after a three second count-down
and showed “1.0KM/H”. It is running until 99 seconds. Press STOP button to
stop your workout, all data is cleared and in manual mode. There are also have
these two quick button on the handrail.
1.5.2 PROGRAM OPERATION
Press PROGRAM button to scroll through the manual mode and P1-P12 Preset
programs. Manual mode is the default operation mode of the system. The default
speed of manual mode is from 1.0km/h to 10.0km/h.
1.5.3 MODE OPERATION
Press PROGRAM button to scroll through H-1,H-2 and H-3.H-1 for time count-down
mode,H-2 for distance count-down mode,H-3 for calories count-down mode. When
you select each mode, you also can press speed +/- key to set value what you
want, then press “START” key to run the treadmill.
1.5.4 SPEED OPERATION
“SPEED+” is the button for increasing speed. “SPEED-” is the button for
reducing speed. When the treadmill is running, you can press “SPEED+” and
“SPEED-” to adjust speed.
2.1 DISPLAY FUNCTION
2.1.1 SPEED DISPLAY Display current running speed.
2.1.2 TIME DISPLAY Display the running time of manual mode or the running time
count-down of program and mode.
2.1.3 DISTANCE DISPLAY Display the accumulative distance of manual and program
mode or the running distance count-down of mode.
2.1.4 CALORIES DISPLAY Display the accumulative calories of manual and program
mode or the running calories count-down of mode.
2.1.5 DISPLAY DATA RANGE FROM EACH WINDOW TIME:0:00-99(MIN)
DISTANCE:0:00-99(KM) CALORIES:0.0-990(KC) SPEED:1.0-10.0(KM/H)
3.1 MANUAL MODE Each program divided running time into 10 intervals; the speed
on each interval has been Preset in the factory.
4.1 PARAMETER SETTING IN THREE MODES Countdown set to 10:00 minutes, setting
range 5:00-99:00,step by step 1:00. Counting calories set to 50Kcal,setting
range 200-990Kcal,step by step 10. Counting distance set to 1.0km,setting
range 1.0-99.0km,step by step 1.0. The cycle switching sequence is manual,
time, distance, calories.
5.1 OTHER
5.1.1 When some counting parameters running end, display screen show END, it
will ring 0.5 second in every 2 seconds until treadmill stop running, then
turn back to manual mode states.
5.1.2 In setting some parameters, you can set in circling. For example, time
setting range 5:00-99:00,when time is set to 99:00,press “+” button, can turn
back to 5:00.Increase and decrease use “+””-” button.
5.1.3 Countdown: Time/Calories/Distance, you just can set one of them, running
as per the last setting, the setting parameters is counted down, other
parameters are counted forward.
5.1.4 The standard value for calories is 30 kcal / km.
6.1 Error code and trouble-shooting
EXPLODED DRAWING
PARTS LIST
MAINTENANCE
LUBRICATION
Lubricating under the running belt will ensure superior performance and extend its life expectancy. After the first 25 hours of use (or 2-3 months) apply some lubricant, and repeat for every following 50 hours of use (or 5-8 months).
How to check running belt for proper lubrication Lift one side of the running
belt and feel the top surface of the running deck. If the surface is slick to
the touch, then no further lubrication is required. If the surface is dry to
the touch, apply some lubricant. How to apply lubricant Lift one side of
running belt. Pour some lubricant under the centre of the running belt on the
top surface of the running deck.
Run on the treadmill at a slow speed for 3 to 5 minutes to evenly distribute
lubricant. NOTE: DO NOT over lubricate running deck. Any excess lubricant that
comes out should be wiped off.
Lubricant Oil
BELT ADJUSTMENT
The running belt is pre-adjusted to the running deck at the factory, but after
prolonged use it can stretch and require readjustment. To adjust the belt,
turn on the main power switch of the treadmill and let the belt run at a speed
of 8-10 KPH. Use the 6 mm Allen Wrench provided to turn the rear roller
adjustment bolts in order to centre the belt. If the running belt is shifting
to the left, turn the left adjustment bolt 1/4 turn clockwise, and the running
belt should start to correct itself.
If the running belt is shifting to the right, then turn the right adjustment bolt 1/4 turn clockwise, and the belt should start to correct itself. Keep turning the adjustment bolts until the running belt is properly cantered.
If the running belt is slipping during use, turn off and unplug the treadmill. Using the 6 mm Allen Wrench provided, turn both left and right rear roller adjustment bolts 1/4 turn clockwise, then turn the main power switch back on and run the treadmill at a speed of 8-10 KPH. Run on to the running belt to determine if the belt is still slipping. Repeat this procedure until the belt no longer slips.
Product Specification
Contact Us
APP Installation
-
Compatible with the following mobile operating system
-
turn on your mobile phone’s Bluetooth and Wifi or 3G/4G
-
Scan the QR below to Install Fit show app
https://play.google.com/store/apps/details?id=com.fitshow&hl=en_IN&gl=UShttps://apps.apple.com/in/app/fitshow/id1387360716
Download and operate Bluetooth APP
2.Register and login
-
You need to register a new account and code if you are a new user, in order to keep your exercise record. If not, you can input your account and code, then enter it.
-
Please register with your E-mail or phone number, then input your registered fit show account and code.
-
Link your phone and treadmill
1).Open Bluetooth, APP will be searched treadmill that can be connected nearby, and automatically switch to your nearest treadmill.
2).Select more mode, you can choose the motion program you want to use by sliding left and right, include target mode, scene mode. Then, press START button to run. -
Operation of mobile phone APP connecting with treadmill 1).Open mobile phone Bluetooth: Ready state of treadmill, open mobile phone Bluetooth
2).Connecting fit show APP :a. open mobile phone fit show APP.
a. Press “search appliance”
b. When the treadmill icon and Bluetooth name (FS-BE9CB3) appears in the center of the mobile screen, press on the bottom of the mobile phone screen ” connecting appliance”
c. Press “START” button
d. Mobile phone can show exercise parameter of treadmill
User Manual All information is correct at the time of print
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>