HARMAN Kardon Citation 200 Portable Smart Speaker with HD Sound User Manual

: June 6, 2024
: Harman

HARMAN Kardon Citation 200 Portable Smart Speaker with HD Sound User

Manual

1. APP

Google Assistant setup

All product features will be set up.

AirPlay setup

For AirPlay only users, skip the Google Home app; on your iOS device, go to Settings > Wi-Fi and select “Citation 200” under SET UP NEW AIRPLAY SPEAKER … Follow the onscreen instructions to complete setup. Google Assistant and Chromecast built-in™ will require additional set up with the Google Home app.

2. PRODUCT TOUR

Citation 200 X1

Regional power cord
(varies depending on country)

Charging cradle X1

3. CHARGING

4. GET STARTED

Add Citation 200 to your home Wi-Fi network:

Download and run the Google Home app on a phone or tablet.
Follow the instructions on the touch screen and Google Home app to finish the setup. * On your Android device, enable Bluetooth and the location service; on your iOS device, enable Bluetooth.

5. Chromecast built-in™

Step 1: Open Chromecast-enabled app.
Step 2: Play Music.
Step 3: Tap the cast icon and select “Citation 200”. e.g.
Spotify Pandora
TuneIn Deezer Google Play Music

Device can support multi-room control provided by Chromecast built-in, more details you can refer to Google Home app.

6. AirPlay

Step 1: On an iOS device, enter the Control Center.
Step 2: Tap to select “Citation 200” as speaker.
Step 3: Start audio streaming from an app.

7. GOOGLE ASSISTANT

8. TONE CONTROLS

9. OWNER’S MANUAL

Download the full owner’s manual from harmankardon.com

10 . SPECIFICATIONS

Model Name: CITATION 200
Power supply: 100 – 240 V ~ 50 / 60Hz
Output power: 50 W RMS
Bluetooth version: 4.2
Bluetooth transmitter frequency range: 2402 – 2480 MHz
Bluetooth transmitter power: <10 dBm (EIRP)
Bluetooth transmitter modulation: GFSK,π/4 DQPSK, 8DPSK
Wireless network: 802.11a/b/g/n/ac (2.4GHz/5GHz)
2.4G Wi-Fi transmitter frequency range: 2412 – 2472 MHz (2.4GHz ISM Band, USA and Canada 11 Channels, Europe and others 13 Channels)
2.4G Wi-Fi transmitter power: <20 dBm (EIRP)
2.4G Wi-Fi modulation: DBPSK, DQPSK, CCK, QPSK,BPSK,16QAM, 64QAM
5G Wi-Fi transmitter power: < 23 dBm (EIRP)
5G Wi-Fi modulation: QPSK, BPSK, 16QAM, 64QAM, 256QAM
5G Wi-Fi transmitter frequency range: 5.15 – 5.35 GHz, 5.470 – 5.725 GHz, 5.725 – 5.825 GHz.

Information on power consumption. This equipment complies with European Commission Regulation (EC) No 1275/2008 and (EU) No 801/2013.
Off

(all wireless connections are deactivated)

| 0.5 Watt
---|---
Networked standby| 2.0 Watt
2. The period of time after which the power management function switches the equipment automatically into:
Off| Short press power key|
---|---|---

Networked standby

|

If the device is connected with Bluetooth or Wi-Fi

| the device shall enter

2.0 Watt networked Standby automatically in 20 minutes.

If this equipment has wireless network connections:
How to activate wireless network connections:
• Set up the product according to instructions;
• Switch into wireless mode (Bluetooth or Wi-Fi);
• Connect with energy using product(s). How to deactivate wireless network connections;
• Short press power key to turn off the device.

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B) / NMB-3 (B).

IC Caution:

User should also be advised that:

(i) the device for operation in the band 5150 – 5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250 – 5350 MHz and 5470 – 5725 MHz shall comply with the e.i.r.p. limit: and
(iii) the maximum antenna gain permitted for devices in the band 5725 – 5825 MHz shall comply with the e.i.r.p. limits specified for pointto- point and non point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250 – 5350 MHz and 5650 – 5850 MHz and that these radars could cause interference and/ or damage to LE- LAN devices.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. No configuration controls are provided for this wireless equipment allowing any change in the frequency of operations outside the FCC grant of authorization for US operation according to Part 15.407 of the FCC rules.

Use Restriction:

This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range in following countries:
Belgium (BE), Greece (EL), Lithuania (LT), Portugal (PT), Bulgaria (BG),
Spain (ES), Luxembourg (LU), Romania (RO), Czech Republic (CZ),
France (FR), Hungary (HU), Slovenia (SI), Denmark (DK), Croatia (HR),
Malta (MT), Slovakia (SK), Germany (DE), Italy (IT), Netherlands (NL),
Finland (FI), Estonia (EE), Cyprus (CY), Austria (AT), Sweden (SE), Ireland
(IE), Latvia (LV), Poland (PL) and United Kingdom (UK).

This product contains open source software. For your convenience, the source code and relevant build instruction for software licensed under the GPL is available at http//www.harmankardon.com/
opensource. You may also obtain this information by contacting us at [email protected]

SAR/RF Exposure information

This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. The device has been tested and meets applicable limits for radio frequency (RF) exposure.

Specific Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. The SAR limit is 1.6 watts per kilogram in countries that set the limit averaged over 1 gram of tissue and 2.0 watts per kilogram in countries that set the limit averaged over 10 grams of tissue. During testing, the device radios are set to their highest transmission levels and placed in positions that simulate uses against the head, with no separation, and when worn or carried against the torso of the body, with 5mm separation. To meet RF exposure guidelines and reduce exposure to RF energy during the operation, the device should be positioned at lease this distance away from the body.

Although this device has been tested to determine SAR in each band of operation, not all bands are available in all areas. Bands are dependent on your location.

The highest SAR values are as follows: