Farpointe Data PCR-35L Mobile Ready Proximity Readers User Guide

June 6, 2024
Farpointe Data

QUICKSTART GUIDE
CONEKT® MOBILE-READY PROXIMITY READERS

This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made.
Models include Conekt PCR-35L, PCR-620L, and PCR-640L. For additional information please reference Farpointe Data’s website, www.farpointedata.com.

Introduction

A key component of a physical security electronic access control system, a mobile-ready reader combining BLE and proximity technologies is based on RFID technology. In operation, it is capable of reading data stored on a proximity credential via radio frequency—or reading data from mobile credential stored in a smartphone’s wallet app via BLE  technology—and without physical contact, and then passing the data obtained to the physical access control system. Access control systems typically manage and record the movement of individuals through a protected area, such as a locked door.

Mounting Provisions

Each reader may be installed either indoors or outdoors. Mounting options are shown in the table below. Use supplied #6 mounting screwsor equivalent security screws, for installation.

Model Mullion Mount **Single-Gang Wall Mount***
PCR-35L
PCR-620L
PCR-640L

*Plastic or metal

Reader Wiring

Wiegand

Conductor| Function
Red| DC (8-14 VDC)
Black| Ground
Green| Data 0
White| Data 1
Brown| Red LEDa
Orange| Green LED b
Yellow| Card Present
Blue| Beeper
Violet| flea powder
Drain| Shield Ground
Magstripe

Conductor| Function
Red| DC (8-14 VDC)
Black| Ground
Green| Clock
White| Data
Brown| Red LED
Orange| Green LED
Yellow| Card Present
Blue| Beeper
Violet| flea powder
Drain| Shield Ground

WIRING NOTES:
aSingle Line LED: This is the standard operating mode and does not make use of the Orange conductor. The LED is Red when the reader is idle and flashes when a card is presented. The LED turns Green when the Brown Conductor is pulled low by the access control panel.
bDual Line LED: This mode makes use of both the Brown and Orange conductors. The Brown conductor controls the Red LED and the Orange conductor controls the  Green LED. LED states are determined by the access control system option and capability.
Unused conductors should be trimmed, isolated, and taped back to prevent unintended current flows. Apply positive voltage only to the Red DC Conductor.

Cable Requirements

24 AWG minimum, multi-conductor stranded with an overall foil shield for example Belden 9535 or similar, supporting the five conductors comprising the physical layer of the  Wiegand interface (power, ground, data 0, data 1, and/or beeper and LED). Alternatively, Belden 9539 or similar, for all reader functions. Contact your access control system manufacturer for their specific requirements. Per the SIA’s Wiegand specification, the maximum cable length is 500 feet (152 m).

Output Formats

  • Wiegand (industry standard 26-bit Wiegand and custom Wiegand formats)
  • Magnetic Stripe (ABA Track II, clock and data, with card present)

Grounding

Shield (drain) continuity must run from the reader to the access panel.
Shield (drain) and reader ground must be tied together at the access panel and connected to earth ground at one point.

Power

Reader may be powered by the access panel. A linear power supply is
recommended for best operation.

Voltage and Current

Voltage: 8 to 14 VDC
Current Draw: 60mA typical, 90mA peak

fleaPower™ Control Line

To reduce the average current required by the reader, pull the purple conductor low.

Connection

Connection must be done in accordance with NFPA 70. Do not connect to a receptacle controlled by a switch. Connect to a power-limited DC voltage source.

Troubleshooting

  1. When the reader is first powered on it will beep 4-times, and the LED will shine red.
  2. Presenting a supported access credential will result in the reader beeping and the LED flashing once.
  3. Mobile operation is optimized for smartphones supporting BLE (Bluetooth LE) version 4.2 or newer. Further, for the downloading of mobile access credentials, a stable,  high-quality internet connection is recommended.

NOTE: The access panel controls LED functionality, such as switching the LED to green.
If the reader does not recognize the mobile credential or card or tag (no beep, no LED flash) or exhibits short read range, please see the table below for possible causes and solutions.

Possible Cause

|

Corrective Action

---|---
Incorrect cabling| Verify gauge, connections and cabling length
Not enough power| 12 VDC recommended
Incorrect credential used| Verify if credential technology is supported
Reader/access panel not properly grounded| Earth ground needed —verify shield and reader ground are tied at  access panel and connect to ground at one point
Supply generating interference| Linear power supply recommended, verify switching power supply before use

Should any of the corrective actions mentioned above not improve performance, disconnect the reader from the access panel and power with a separate power supply or 9VDC  battery, and re-test card functionality. By powering the readers separately, most variables that may lead to reduced performance can be eliminated. Should the problem persist, please contact Farpointe directly?

Operating Temperature: –31° F to +150° F (–35° C to +66° C)
Operating Humidity: 0% to 90% Relative Humidity
IP Rating: IP67-rated for outdoor use

Access Control Performance Levels Conforming to UL STD 294:

Model

| Destructive Attack| Line Security| Endurance|

Standby Power

---|---|---|---|---
PCR-35L| Level I| Level I| Level IV| Level I
PCR-620L| Level II| Level I| Level IV| Level I
PCR-640L| Level II| Level I| Level IV| Level I

Grade Classification Certified to CAN/ULC STD 60839-11-1:

Risk Level| Application| Skill/Knowledge of Attackers| Typical Examples
---|---|---|---
Grade 2| Grade 2| Grade 2| Grade 2

Many Farpointe Data Readers carry the following certifications:

FCC Compliance Statement: This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by Farpointe Data could void the user’s authority to operate the equipment.
The product can be used without license conditions or restrictions in all European Union countries, including Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Spain, Sweden,  United Kingdom, as well as other non-EU countries, including Iceland, Norway, and Switzerland.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

For proper PIN security with keypad readers, please review our
PIN Best Practices Reference Document.

Farpointe Data reserves the right to change specifications without notice.

http://www.farpointedata.com
Apr-22-2021

© 2021 Farpointe Data, Inc. All rights reserved. Farpointe Data®,
Pyramid Series Proximity®, Delta®, Ranger®, and CONEKT® are the registered U.S. trademarks of Farpointe Data, Inc. All other trademarks are the property of their respective owners.
www.farpointedata.com

Farpointe Data, Inc.
2195 Zanker Road
San Jose, CA 95131 USA
Office: +1-408-731-8700
Fax: +1-408-731-8705
support@farpointedata.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals