eurofone T20s Motorcycle 6 Riders Full-Duplex Stereo Bluetooth Wireless Helmet Headsets User Manual

USER MANUAL

Model:V6 PLUS_T20S
Bluetooth Headset
Manufacturer: Shenzhen Winnerelec Industrial Co., LTD
Address:411-416 Room Social security building,
Honghua Bei Road Gongming Street Guangming New District, Shenzhen, China

Introduction

Thank you for choosing the T20s Motorcycle 6 Riders full-duplex stereo Bluetooth wireless helmet headsets, designed for installing into most open- face, flip-front, and full-face style helmets.

With the T20s, you can call hands-free on your Bluetooth mobile phone, listen to music or voice instructions of GPS navigation, and activate wireless intercom for the rider to rider or rider to passenger intercom talk within a range of 1200 meters(depending on terrain conditions).

The T20s is compliant with Bluetooth Specification V3.0 supporting the following profiles: Headset Profile(HSP), Hands-Free Profile(HFP), and Advanced Audio Distribution Profile (A2DP), and Audio Video Remote Control Profile(AVRCP), and Audio Gateway (AG). It supports universal pairing with most Bluetooth headsets on the market. The user can activate Siri or S-Voice from the main unit for voice dialing and other voice commands. The FM radio tuner is built into the main unit and allows for station scanning.

Superior audio fidelity has been achieved with our high fidelity, non-ported, and ultra-slim helmet HD speakers. This headset also provides the industry’s best combination of wind and ambient noise reduction with the miniature boom microphone. Please read this User Manual carefully before using this product.

Packet Content

HIFI Speaker and Microphone

Clip Mounting Bracket
User Manual

Fixed installation method

1. Locate the helmet at the left and clean it up
2. Peel off the 3M rubber protective film
3. Apply pressure to the metal carrier to secure the holder firmly
   Note: it takes 24 hours after drying.

Temporary installation method

1. Clip-on the left edge of the helmet
2. Remove metal handle after installation
3. If required, use additional anti-slip rubber patches

Install host

1. Slide host off the top of the clip and you’ll hear a click when it is completely plugged in V6S PLUS_T20S
2. Plugin the 3.5mm headset plug

Headset mounting method

1. Stick the left and right horns of the headphones in the position of the left and right ears of the helmet
2. Keep the microphone in front of the mouth，

Note: microphone holes point to the mouth

Charging

1. You can charge with the Micro USB cable in the package. During charging, OLED shows “Charging”. After full charging, OLED shows “Charged full”, and it is recommended to recharge the battery before each use. Suggest full charge before each use.
2. Low battery warning: Headset will automatically voice prompt low battery at every 5 minutes to prompt the user to recharge it.
3. Battery state notifies: When standby, double press the Power button to report battery level.

General Operation Instructions

Power on /Power off
Press the Power button for approx. 3S, the screen display “Power on”, and it powers on.
When power-on status, press the Power button for approx. 1s, the screen display “ Power off”, and its power off.

Pairing with Cell Phone or GPS and Using

Mobile Phone/GPS pairing steps

1. When powering off, press the Power button for approx 8S, the screen display “Pairing”, Open the phone Bluetooth, search for “ ”, then click on the phone connection pair. After the pairing, V6S PLUS_T20S the screen display “Paired” and goes back to standby mode.

Answer phone calling:
The unit will automatically answer the incoming call after 12 seconds. Or press the Phone button to answer the incoming phone call immediately.

Reject incoming call:
When have incoming calls, double press the power button 2 times to reject within 12s?

End phone calling:
During talking, short press Phone button to end the call。

V oice dial:
When phone standby, double press Volume – button to make voice dialing (The phone itself must have a voice dialing function)

Last number redials:
When cell phone standby, double press Volume + button to make last number redialing.

Memory connects with a cell phone:
Once pairing with a cell phone, when power on again, the headset will re- connect with the mobile automatically. Or in case of disconnect during standby mode, short press Phone button will connect again.

Connect third party calls:
When connecting two cell phones, during a phone call with a first cell phone and second cell phone dial-in, can double press the Phone two times to answer the second cell phone and hold the first cell phone conversation. When finish the second cell phone conversation, will back to the conversation with the first cell phone.

Music Control:
Press the Phone button to play and pause the music. When playing music, double press Volume + button to go to the next track, double press the Volume – button to go to the previous track.

Voice Volume Control:
Short press Volume + button or Volume- button adjust the voice volume. Or while music or talking state, long press Volume+ button or Volume – button adjust the voice volume.

FM RADIO

Turn on/off the radio
When in standby mode, press and hold the Volume+ button or Volume – button 1 second to turn on
FM radio. Press and hold it again for 1 second to turn off the FM radio.
FM Radio Station Search
While in FM mode, double press the Volume + button or Volume – button two times to search a next/previous FM channel.
Preset and store up to 6 FM radio stations
In FM radio mode, when a favorite station is found, long-press the Phone button 1 second to save, a beep tone will sound. Preset and store up 6 FM radio stations. Once 6 stations have been saved, saving a new station will overwrite the oldest saved station. Press the Phone button to rotate between each saved station.

Universal Pairing and Using

Power on another brand Bluetooth device into pairing suitable, meanwhile T20s at standby mode, long press Intercom B button 1 second, and screen display “pairing”, then short press Intercom B, and screen display “Searching”. After pair successfully, the screen display “Paired”. After paired, while at standby mode, short press Volume+ and Volume- button at the same times, reconnect with Bluetooth headset which connected before and start talking. V6 PLUS_T20S While in talking mode, short press the Phone button to end it.

Bluetooth Intercom Talk

They can be paired with other T20s for up to a total of 6 units for full- duplex Bluetooth V6 PLUS_T20S
intercom.

Pairing Two headsets and talk

Step 1: Power on unit 1 and unit 2, then long-press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode. Step 2: After the pair is finished, Short press Button B on either unit, it will start the intercom, and the screen displays “Intercom B”. During Intercom talking, short press the Phone button to exit intercom mode.

Pairing Three T20s headsets and talk

Step 1: Power on unit 1 and unit 2, then long-press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 2: Power on unit 1 and unit 3, then long-press unit 1 and unit 3 Button C, the screen display “Pairing” of all, then short press Button C on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 3: After the pair is finished, Short press Unit 1’s Button B on either unit1 and unit2, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.
Step 4:After the pair is finished, Short press Unit 1’s Button C on either unit1 and unit3, it will start intercom, and screen display “Intercom C”. During Intercom talking, short press the Phone button to exit intercom mode.

Pairing Four headsets and talk

Step 1: Power on unit 1 and unit 2, then long-press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 2: Power on unit 1 and unit 3, then long-press unit 1 and unit 3 Button C, the screen display “Pairing” of all, then short press Button C on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 3: Power on unit 1 and unit 4, then long-press unit 1 and unit 4 Button D, the screen display “Pairing” of all, then short press Button 4 on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 4: After the pair is finished, Short press Unit 1’s Button B on either unit1 and unit2, it will start the intercom, and the screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.
Step 5:After the pair is finished, Short press Unit 1’s Button C on either unit1 and unit3, it will start the intercom, and the screen display “Intercom C”. During Intercom talking, short press the Phone button to exit intercom mode.
Step 6:After the pair is finished, Short press Unit 1’s Button D on either unit1 and unit4, it will start the intercom, and the screen display “Intercom D”. During Intercom talking, short press the Phone button to exit intercom mode.

Pairing Five headsets and talk

Step 1: Power on unit 1 and unit 2, then long-press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 2: Power on unit 1 and unit 3, then long-press unit 1 and unit 3 Button C, the screen display  “Pairing” of all, then short press Button C on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 3: Power on unit 1 and unit 4, then long-press unit 1 and unit 4 Button D, the screen display “Pairing” of all, then short press Button 4 on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 4: Power on unit 1 and unit 5, then long-press unit 1 and unit 5 Button E, the screen display “Pairing” of all, then short press Button 5 on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 5: After the pair is finished, Short press Unit 1’s Button B on either unit1 and unit2, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode.
Step 6:After the pair is finished, Short press Unit 1’s Button C on either unit1 and unit3, it will start the intercom, and the screen displays “Intercom C”. During Intercom talking, short press the Phone button to exit intercom mode.
Step 7:After the pair finished, Short press Unit 1’s Button D on either unit1 and unit4, it will start the intercom, and the screen display “Intercom D”. During Intercom talking, short press Phone button to exit intercom mode.
Step 8:After the pair is finished, Short press Unit 1’s Button E on either unit1 and unit5, it will start the intercom, and the screen display “Intercom E”. During Intercom talking, short press the Phone button to exit intercom mode.

Pairing Six headsets and talk

Step 1: Power on unit 1 and unit 2, then long-press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 2: Power on unit 1 and unit 3, then long-press unit 1 and unit 3 Button C, the screen display “Pairing” of all, then short press Button C on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 3: Power on unit 1 and unit 4, then long-press unit 1 and unit 4 Button D, the screen display “Pairing” of all, then short press Button 4 on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 4: Power on unit 1 and unit 5, then long-press unit 1 and unit 5 Button E, the screen display “Pairing” of all, then short press Button 5 on either unit, then the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 5: Let unit 1 and Unit 6 in power-off state, then long-press unit 1 and unit 6 Power button about 6 seconds, the screen display “Pairing” of all, and short press Power button on either unit, the unit’s screen displays “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 6: After the pair is finished, Short press Unit 1’s Button B on either unit1 and unit2, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press the Phone button to exit intercom mode.
Step 7:After the pair is finished, Short press Unit 1’s Button C on either unit1 and unit3, it will start intercom, and screen display “Intercom C”. During Intercom talking, short press the Phone button to exit intercom mode.
Step 8:After the pair is finished, Short press Unit 1’s Button D on either unit1 and unit4, it will start the intercom, and the screen displays “Intercom D”. During Intercom talking, short press the Phone button to exit intercom mode.
Step 9:After the pair is finished, Short press Unit 1’s Button E on either unit1 and unit5, it will start intercom, and the screen displays “Intercom E”. During Intercom talking, short press the Phone button to exit intercom mode.
Step 10:After the pair is finished, Short press Unit 1’s Button power on either unit1 and unit6, it will start the intercom, and the screen display “Intercom A”. During Intercom talking, short press the Phone button to exit intercom mode.

Answer third intercom call:
When two devices have started the intercom talking, the other intercom call in, the unit who be called have a tone to notify, and double press the Phone button two times on the unit to answer the incoming intercom call.  ****

Technical specifications ：

1. Bluetooth 3.0 Support : HSP,HFP,A2DP,AVRCP, ASP
2. Working hours: 12 hours
3. Standby time: 300 hours
4. Charging time: 3 hours
5. Battery: lithium containing rechargeable lithium battery 650mAH, 3.7v
6. Dimensions: 87cm 45cm 26cm
7. Weight: 50g
8. Certification ：CE, FCC, TELEC

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information:
FCC RF Exposure requirements: The highest SAR value reported under this standard during product certification for use next to the head with the minimum separation distance of 0 mm is W/Kg. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. This product is in compliance with FCC RF exposure requirements and refers to
FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: 1.342 2AQN2-V6PLUST20S

MADE IN CHINA
Web: www.winnerelec.com
E-mail: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>