IMOU DB11 Doorbell Wired User Guide

June 6, 2024
imou

imou logo

IMOU DB11 Doorbell Wired

IMOU DB11 Doorbell Wired

Welcome
Thank you for choosing IMOU.
We are devoted to providing you easy smart home products. If you have problems using the product, please contact our service team before returning your product. Our service mail: service.global@imoulife.com Frequently asked questions can be found at imoulife.com/support/help

Packing Listpackage content

Product Overview

detail 1

Installation

  1. Preparation
    Before beginning setup, there are some essential preparations to make.

    • Turn off the power Running to your existing doorbell and chime box at the breaker.
    • Remove your existing doorbell and disconnect wiring.detail 2
      Tips : Bend the power cables so they do not fall through the hole in the wall. Remove the metal mounting plate from the back of the doorbell.
  2. Secure the mounting bracket
    Next, use the mounting bracket to mark holes for mounting. Use the mounting accessories specified below depending on mounting location.detail
3
    Note : For both installations, ensure the power cables from the wall fit comfortably thtougl the hole in the mounting bracet. detail
4

  3. Add Doorbell to Imou Life Appdetail 5 Tips:detail 6
    ** To ensure the best possible wireless performance, please make sure there are no obstacles and electromagnetic interference between the Doorbell and router. detail 7**

  4. Wiring the doorbell
    Next, you will complete the wiring for your new doorbelldetail
8 detail
9
    Note : If the power cables in the wall are not long enough, use the optional power cable connectors and wire caps.detail
10
    Ensure there is enough space to fit the cable connetors and wire caps into the hole in your wall or frame.detail 11

Troubleshooting

Question Answer

The device cannot boot up?

| •        Please confirm whether power voltage of the device is normal, and whether power cable is well connected.



Connection is overtime?

| •            The device, mobile phone and router are too far away. Please put them within 30cm (12 inches) when configuring.

•            Please reset the device to factory defaults and follow the guide on App page to try again.




The device is not online?

| •        Please check the state of device indicator light. If blue light flickers all the time, it means that the device fails to connect the network. Please check whether wireless router can connect the network; connect your mobile phone with this wireless network to test it. If it can connect the network, please reset the device and configure again.



There is no message when PIR motion detection is triggered?

| •            Please check whether alarm subscription is enabled.

•            If it is enabled, please check whether corresponding PIR zone is enabled.

•            Please check whether zone detection distance is set to be a relatively small range.


How to restore factory settings?

| •        Please press Reset Button on the rear panel of the device for 5s. Blue light will be on for 3s and then turn off; the device will reboot automatically and restore factory default settings.

Safety Tips and Warnings
The following description is the correct application method of the device.Please read the manual carefully before use, in order to prevent danger and property loss. Strictly conform to the manual during application and keep it properly after reading.

Caution:

  • Please don’t place and install the device in an area exposed to direct sunlight or near heat generating device.
  • Please don’t install the device in a humid, dusty or fuliginous area. Please keep its horizontal installation, or install it at stable places, and prevent it from falling.
  • Please don’t drip or splash liquids onto the device; don’t put on the device anything filled with liquids, in order to prevent liquids from flowing into the device.
  • Please install the device at well-ventilated places; don’t block its ventilation opening.
  • Use the device only within rated input and output range.
  • Please don’t dismantle the device arbitrarily.
  • Please transport, use and store the device within allowed humidity and temperature range.
  • Products with category I structure shall be connected to grid power output socket, which is equipped with protective grounding.

Disclaimers: This doorbell includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the doorbell. This clicking is normal, and indicates that the camera filter is working.

@imouglobal
E-service:global@imoulife.com
Website:www.imoulife.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals