saferhomee T704 Wireless Alarm System User Manual

June 6, 2024
saferhomee

Wireless Alarm System, T704

User Manual

Note:
contact@saferhomee.com

  1. The alarm system is pre-programmed , please proceed to part 2 of the manual for setup. (Or please search “ HTZSAFE T704 &806A SETUP“ on YouTube, there is a video for your reference)
  2. If you want to add additional HTZSAFE sensors to the system, program them according to part 3 of the manual or contact us directly. (Or please search “ HTZSAFE T704 to 806A Connect “ on YouTube, there is a video for your reference)

After-sale Service:

E-mail: contact@saferhomee.com

1. System Components And Usage

Plug-in Alarm Receiver

Plug-in Alarm Receiver

Power Plug: plug the receiver into a socket
Volume: 4 adjustable volume levels
Melody: 35 optional melodies
Zone Number: flash for several seconds when the sensor be activated

Speaker

Speaker: Sound for several seconds when the sensor be activated

Solar Wireless Motion Sensor

Solar Wireless Motion Sensor

Sensor Eye: Detects heat movements
Solar Panel: Charges the built-in battery of the sensor

Drain Hole: Used to drain out the rainwater(please note the drain hole must be facing down when you install the sensor)

Charge Jack

Charge Jack: Used to connect the additional solar panel or DC 5V power adapter
ON/OFF: Sensor on/off

ATTENTION PLEASE

The KIT includes a USB charging cord without a AC adapter which is used to manually charge the solar sensor before use or after pro- longed low light conditions causing low battery.

Please kindly connect the charging cord with your own USB plug(such as the direct USB outlet, the phone’s USB plug or computer’s USB, etc.).If needed, please charge the sensor for 4 hours with the USB charging cord as below:

KIT includes

2. Operation Instructions

Step – 1
Plug the receiver into an outlet

Step - 1

Ring tone prompt and the zone number
will light up one by one for 3 times meaning
the receiver works properly.

Step – 2
Turn on the Wireless Motion Sensor:
Press the ON/OFF button 4 times

Step - 2

(bleep prompt meaning normal operation)

Step – 3
Activate The Wireless Motion Sensor
(wait about 30 seconds after you turn on the sensor)
1st Method: Press the ON/OFF button twice

Step - 3

(The light of the ON/OFF button will flash once meaning
the motion sensor was activated and sent the wireless signal)

2nd Method: Walk through in front of the sensor to activate

2nd Method

(The light of the ON/OFF button will flash
once meaning the motion sensor was activated and sent the wireless signal;then the motion
sensor will automatically reset after a few seconds ready for next trigger)

Step – 4
Press “Melody” once to choose the melody for this sensor, total 35 optional melodies.

Step - 4

Step – 5
Same operation if you have the additional sensor, and please refer to part 3 of the manual for other settings.

Step – 6
Installation

Wireless Motion Sensor

Wireless Motion Sensor

Installation Notes:

1. Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind.

installation

2. Please point the sensor towards a open field (not towards the trees or bushes)

Please point the sensor

3. Please adjust the sensor a little down(never upwards)

adjust the sensor

4. Please point the sensor eye towards to the engine or exhaust pipe if detecting vehicles.(the working principle of the senor is detecting the movements with heat sources)

3. Other Settings

(1) How to add additional sensors to the receiver
(up to 4 sensors can be added to one or multiple receivers)

Step – 1
Plug the receiver into an outlet

Step – 2

Press and hold the “Volume” button for 5 seconds, release the button when one of the zone number flashing and a beep prompt

Step - 2

Step – 3
Note:
Activate the sensor.
Please have the sensor close to the plug- in receiver when programming. (within 30FT )

Activate the sensor

Step – 4

Activate the sensor again to confirm the sensor has been added to the receiver already.

Step – 5

Press”Melody”button to choose the melody for this sensor. total 35 optional melodies .

Step – 6

Same steps to add more sensors to the plug-in receiver.
(For example: add the 2nd sensor to the receiver)
Press and hold the “Volume button” for 5 seconds
—–release the button when the Zone 2 flashing slowly
(zone 1 lights up meaning one sensor has been added to zone 1 already)—-activate the 2nd sensor once
—-Zone 2 flashing quickly and a ring tone prompt meaning the 2nd sensor has been added to the receiver.

Note please: the receiver has 4 zones and up to 4 sensors can be added to 1 receiver.(the receiver will have a long beep prompt if you operate to add more than 4 sensors to 1 receiver)

(2) How to delete the sensors of the receiver

Step – 1
Plug the receiver into an outlet
Step – 2
Press and hold both the “Volume” button and “Melody” button for 10 seconds and release the buttons when you hear a long beep prompt;
Note: all the sensors will be deleted by this operation.

delete the sensors of the receiver

(3) How to adjust the volume

Step – 1
Plug the receiver into an outlet
Step – 2
Press the “Volume” once to adjust the volume of the receiver.
(total 4 adjustable volume levels)

adjust the volume

(4)How to change the melody for the sensors

(total 35 optional melodies, you can match a different melody for each sensor)
Step – 1
Plug the receiver into an outlet
Step – 2
Activate the sensor first, and then press the “Melody” button to choose the melody for this sensor
Repeat steps for other sensors which have been added to the receiver already.

(5) How to adjust the sensitivity of the sensor

The sensor has 3 adjustable sensitivities(Low,Medium,High)
Step – 1
Turn off the sensor first
Press the ON/OFF button 3 times to turn off the sensor
(it will long beep prompt)

Step – 2
To select Low sensitivity- – – – turn on the sensor by pressing the ON/ OFF button 3 times.
To select Medium sensitivity- – – – turn on the sensor by pressing the ON/ OFF button 4 times.
To select High sensitivity- – – – turn on the sensor by pressing the ON/ OFF button 5 times.

4. Technical Parameters

Plug-in Alarm Receiver

Plug-in Alarm Receiver

Technical parameters

Technical parameters

Wireless Motion Sensor

Wireless Motion Sensor 45mm

Technical Parameters

Technical parameters

After-sale Service:
E-mail: contact@saferhomee.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals