Mousetrapper Alpha Ergonomic Mouse and Keyboard User Guide
- October 27, 2023
- MouseTrapper
Table of Contents
Getting started with Mousetrapper Alpha
Valid from firmware 4.3.23
User Guide
Connecting Mousetrapper
Bluetooth connection
Slide the power switch on the underside to ON. Once the Mousetrapper is
discoverable, you will see a flashing blue light. Pair your Mousetrapper via
the computer’s luetooth
menu. Once it is paired to the computer, the blue light will flash rapidly and
then stop flashing.
Cable connection
Connect the supplied cable to the socket on the left side of your
Mousetrapper, and connect the other end to a USB port on the computer.
Charging
The battery in the Mousetrapper needs charging when the battery indicator
flashes red. Connect the Mousetrapper using the supplied USB cable and allow
it to charge. During charging the LED will flash green and turn solid green
when fully charged.
Changing from Mac to PC configuration
The product is configured for PC on delivery. To configure it for Mac, press
the lower right and lower left buttons (Copy and Paste) at the same time as
you click on the control pad for 3–4 seconds. The LED will flash fast in pink
to confirm the setting. Repeat the procedure to change back into PC mode. The
LED will flash slow in pink to confirm the PC mode setting.
Basic tips
Firmware updates
Make sure you keep your Alpha updated with the latest firmware. To update the
firmware, launch MT Keys with the cable connected. Click the cloud in the
upper part of MT Keys and follow the instruction. During the update process
the LED will flash red and green. Do not disconnect the cable during this
process.
Scrolling
To scroll using the control pad, place your finger on the right edge of the
control pad. There is no need to press on the control pad; simply slide your
finger up or down the edge, depending on which way you want to scroll.
Bluetooth devices
The Mousetrapper Alpha can be paired to two separatedevices at the same time.
One on Channel 1 and one onChannel 2. This means that you for instance can
switch between your computer and your smart tv or phone.
To switch between the channels press Fn and Ch.1/ F1 or Ch.2/F2 at the same
time. When pairing the LED will flash blue for Channel 1 and double flash blue
for Channel 2.
The Alpha remembers and reconnects up to four devices. When pairing to a
fifth, the oldest will be cleared from memory.
To clear all bluetooth devices in memory press Fn and Del at the same time as
you click on the control pad. The LED will rapidly flash pink to confirm that
the memory is cleared.
Customising
MT Keys
You can customise the functions of the buttons around the control pad as well
as the keys F1 to F11. To do this, you need to download the software MT Keys
either via www.mousetrapper.com/mtkeys or via Microsoft Store if you have
Windows 10. Then follow the instructions to install the software. An image of
the product will appear once MT Keys is installed and the USB cable is
connected to your Mousetrapper. Position the cursor over the button you want
to customise. Click on it by lightly pressing on the control pad once. You
will now see a pull-down menu that lets you assign whichever action you want
to that button.
You can choose between functions such as adding an extra left-click, creating
shortcuts and inserting text by pasting it in.
Responsible party name: Mousetrapper North America Inc.
www.mousetrapper.com
info@mousetrapper.com
Hereby declares that the
Product: Mousetrapper (Wireless HID mouse/keyboard)
Model name: Alpha MTV12
Modification Statement:
Changes or modifications to the equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Class B Interference Statement:
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement:
This portable device with its antenna complies with FCC/IC RF exposure limits
for general population / uncontrolled exposure. The antenna used for this
device must not be colocated or operating in conjunction with any other
antenna or transmitter.
CAN ICES-3 (B)/NMB-3(B)
Interference Statement (RSS-GEN Section 8.4):
This Device complies with Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
DISCLAIMER AND LIMITATION OF LIABILITY
This product (the Product) has been manufactured by or on behalf of Trapper
Data AB, Swedish Reg. No. 556872-7597 And its group companies (Trapper Data).
As between Trapper Data and the user, the following shall – to the fullest
extent permitted by applicable law – apply: The Product is provided “as is”
without warranty of any kind (either express or implied), including but not
limited to any implied warranties of merchantability and fitness for a
specific or general purpose and those arising by statute or by law, or from a
cause of dealing or usage of trade. Trapper Data shall have no obligations
whatsoever to repair, replace or service the Product in any manner or to
provide the user with any future upgrades to the Product, if any. The user is
solely responsible for the use of the Product. In no event, regardless of
cause, shall Trapper Data be liable for any direct, indirect, special,
incidental, punitive or consequential damages of any kind, whether arising
under breach of contract, tort (including negligence), strict liability or
otherwise, and whether based on agreement or otherwise, even if advised of the
possibility of such damages. Trapper Data makes no claim or representation
that the Product will prevent, cure, or mitigate any medical condition,
disease, injury, pain or discomfort for all users.
References
- Mousetrapper | Undvik smärta med en ergonomisk datormus.
- Software - Mousetrapper
- Mousetrapper | Undvik smärta med en ergonomisk datormus.
- Mousetrapper | Avoid pain with an ergonomic mouse.
- Software - Mousetrapper
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>