IKEA UPPSPEL Underframe Sit Stand F Table Instruction Manual

IKEA UPPSPEL Underframe Sit Stand F Table Instruction Manual

An electro-mechanically height adjustable worksurface with control interface to adjust height up and down.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved by a person responsible for their safety.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Electrical sit and stand desk

This appliance shall only be used together with the included power supply unit.
Every person who is responsible for this table at installation or employment of the table in daily use or in service and repair work should carefully read these instructions. Keep these instructions close to your sit/stand table.
Installation instructions

• The table is assembled according to separate assembly instructions.
• Connect the electrical cable to a power source.

NOTE! The electrical cable must have full mobility.

• The table is now ready for use. The motors stop automatically when the table reaches its lowest and highest position respectively.

Usage

• The table shall only be used as a gaming table with the possibility to continuously adjust the working height between sitting and standing position.
• The table shall only be used indoors and in dry premises (office environment or similar).

The table must not be overloaded – maximum load is 70KG/154lbs. The system may be run continuously for a maximum of 2 minutes. Afterwards, the motors must stand idle for approx. 18 minutes before they can be used again.

Follow these instructions when adjusting table height:

1. Make sure no objects are in the way of the table.
2. In order to move the table up/down, press the up and down arrow button respectively.
3. The display switches off when not in use for about 10 seconds. Press any button to wake the controller up.

Safety regulations

• When the table is moving up/down, keep the necessary safety distance to avoid the risk of being squeezed between the moving table top and fixed objects in the surrounding area.
• When the table is moving up/down, the user shall make sure that nobody is injured and that no object is damaged. The table top must not bump into a fixed object, causing the table to overturn. Always remove any chair before the table is moved up/down.
• The table tripod must not be altered or reconstructed in any way. In service and repair work of the table, the electrical cable must always be disconnected from the power source.
• Modifications to the legs are absolutely forbidden!
• The table must not be used as a hoisting device for persons.

Maintenance and repair instructions

• After approx. 1 week of use, check that the screws are properly tightened.
• If the table cannot be lowered or raised, check that all electrical connections are connected properly.
• If any part of the electrical system is replaced, the electrical cable must first be disconnected from the power source. Replace the electrical part and then connect the electrical cable to the power source. The table is now ready for use.

If the table still does not work, please contact your nearest IKEA store or customer service.

Manufacturer:
IKEA of Sweden AB Address: Box 702, SE-343 81 ÄLMHULT

SAVE THESE INSTRUCTIONS

Product servicing
Do not attempt to repair this product yourself, since opening or removing protective covers may expose you to dangerous voltage points or other risks.

Troubleshooting guide

NOTE!
Always disconnect the cable from the wall socket before maintenance!

Basic Setting:

Push the arrow down button until the legs have reached the lowest position and keep pressure on the button for 6 seconds more. Upon certain errors, this must be done twice in succession. Now the desk is in initial position.

Initialisation instructions:

Step 1. Continuously press the arrow down button for a few seconds until the desk reaches its lowest position.

Step 2. Continuously press the display shows arrow down button a second time until the “RST”.

Step 3. Continuously press the arrow down button a third time until the desk moves slightly downwards.

When the desk stops moving and the display shows “72”, it is ready to use.

Height Adjustment Controller

Reset process:

Step 1: Press/hold the down button for a few seconds until the table reaches its lowest position.

Step 2: Press/hold the down button a second time until the display shows “RST”.

Step 3: Press/hold the down button a third time until the table slowly lowers. Once the table stops moving and the display shows “72”, your desk is ready to use.

Lock/Unlock controller:

Lock the controller: Press and hold the symbol for 10 seconds until the display shows “LOC”.

Unlock the controller: Press and hold the symbol for 10 seconds until the display shows the actual height of the table.

Error Code Instructions

The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fills and minimise any potential negative impact on human health and the environment. For more information, please contact your IKEA store.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>