Tevo shox recon User Manual

Tevo shox recon User Manual

WHAT’S IN THE BOX?

INSTALLING THE CONTROLLER BATTERIES (not included)

open the battery cover on the back of the controller by unscrewing the screw with the screwdriver included. Place 3 x 1.5V “AA” batteries (not included) into the controller’s battery compartment as per the pie below:

CHARGING THE SHOX RECON BATTERY

1. charge the drone battery fully before first use
2. use the usb charger to charge the drone battery. when the usb charger is plugged into a usb power source the charger light will glow red. when the battery is fully charged, the charger will stop glowing red.

NOTE: this charger Is exclusive to the shoX recon. do not use It with any other devices.

INSTALLING SPARE BLADES

the shoX recon comes with replaceable spare blades in case the original blades become damaged.

1. please make sure to match the spare blades to the originals when installing. See marking on the blade to match.

2. use the screwdriver to unscrew the damaged blade and remove ii to install the replacement blade. make sure to secure screw the replacement blade in place.
3. make sure to use the correct replacement blades for each side. incorrect blade placement will affect the drone’s flight and control.

INSTALLING BLADE PROTECTORS

1. install all 4 blade protectors before flying the drone. failure to do so could result in serious damage to the blades and drone.
2. insert blade protectors as shown below and make sure they are firmly in place

CONTROLLER FUNCTIONS

1. power switch
2. left control lever
3. right control lever
4. speed setting
5. acrobatic flips
6. headless mode
7. reset trim settings
8. take-off
9. land
10. leftward trim adjust
11. rightward trim adjust
12. backward trim adjust
13. forward trim adjust

USING THE APP

1. download and install the “shoX recon” app from the app store or google play store, depending on your device. go to the app store/google play store, search for’ shoX recon’ app and download to your device. once the app Is downloaded you are able to fly the shoX recon with the controller and have five (first person view) or control the flight of the drone with the app itself.
2. turn on the wifi on your device and ensure the drone is switched on. enable your devices’ wifi. turn on the drone. once you see, ‘shoX recon’ app appear as a wifi connection option, select this, then go straight to the “shoX recon” app. once the app is open, on the home page, push the ·calibrate” Outzen and then the ·start” Outzen on the home screen. the drone lights will be flashing. once the drone lights stop flashing you will be paired. you will notice the view on your device will be that of the drone’s camera.

the order in which you ‘pair’ the drone is important. if you want to fly the drone with the controller, then turn on the drone and controller and pair these together before turning on your wifi to connect the app. once these are paired, you can turn on your wifi and connect the drone. to fly the drone with the app, pair the drone with the app first. then the app becomes the controller and the controller is not able to be used. see controls below:

1. back
2. set flight path
3. VR mode
4. flip view
5. gravity sensor mode
6. calibration
7. headless mode
8. menu
9. change speed
10. N/A
11. take photo
12. shoot video
13. switch to optical lens
14. view photo album
15. take-off/land
16. emergency landing
17. switch control mode
18. left control lever
19. right control lever

NOTE: when using the ‘shoX recon” APP to fly/control the shoX recon, the flying range is 30m.
NOTE: the optical lens is not a camera. It functions only as a positioning system.

FLYING PRECAUTIONS

1. the drone will not take-off if the battery is low or flat
2. flying the drone with a chipped or broken blade can cause more damage and/or injury
3. remove the drone battery from the drone when not in use
4. remove batteries from the controller when not in use
5. it is strongly recommended

GETTING STARTED

• ensure all drone and controller batteries are fully charged and correctly inserted.
• ensure the drone legs and blade protectors are attached correctly.

pairing the drone to the controller:

1. plug in the drone battery, turn the drone on and place on flat surface. drone lights will be flashing.
2. turn on the controller. the controller will beep once. move the left control stick up and down. once the drone lights stop flashing, pairing is complete.

NOTE: it is recommended to calibrate drone (press calibration button once in app) after the pairing the process and prior to flight.

FLYING INSTRUCTIONS

after successfully pairing the shoX recon with the controller, complete the following steps before starting your drone:

1. setting headless mode flight direction
   as shown in figure 1, pull the two control sticks to the bottom left at the same time. the lights on the drone will flash slowly to signify that this step is successful. please see “headless mode” operation on page 8 for flight instructions.

2. calibrating the gyroscope
   place the drone on a flat, even surface. as shown in figure 2, pull the 2 control sticks to the bottom right at the same time. the lights on the drone will flash slowly to signify that this step is successful.

NOTE: the gyroscope may require recalibration if the drone has been dropped or experienced any hard collisions.

FINE TUNING

MODE SETTINGS

the shoX recon has 3 speed modes: low speed, medium speed, high speed.

low speed: this setting is recommended for beginner drone pilots. to select this mode, press the “speed setting” button on the controller until you hear one beep to signify that you are in “low speed” mode.

medium speed: this setting is recommended for novice drone pilots. to select this mode, press the “speed setting” button on the controller until you hear two beeps to signify that you are in “medium speed” mode.

high speed: this setting is recommended for expert drone pilots. to select this mode, press the “speed setting” button on the controller until you hear three beeps to signify that you are in “high speed” mode.

HEADLESS MODE

headless mode will allow you to use a different flying direction for the drone, which is the direction the controller is facing, as opposed to the direction the front camera is facing. this direction will remain the forward and backwards motion of the drone, as well as the side to side motion, regardless of drone’s camera facing (see page 9).

after initialling headless mode, the lights on the drone will start flashing. this is to signify that headless mode has been activated. this also sets the direction of headless mode, which is the direction the controller is facing. to exit headless mode, press the “headless mode” button again.

OUT-OF-RANGE PROTECTION

the shoX recon will start a slow landing procedure should ii lose signal with the controller or app, to reduce the risk of an accidental fall or loss of the drone. loss of signal between the control method and drone can occur under these circumstances:

– the remote control loses power or the app is closed or crashes
– Obstacles between the control method and drone interfere with and block the signal
– the signal is interrupted by electromagnetic waves
– the drone is outside of the control range

EMERGENCY STOP

in the event of a hard collision or crash, the drone will engage emergency stop and automatically shut down. this is to prevent any further potential damage to the drone and/or object of collision. please be mindful of this when flying the drone at higher altitudes, because the drone will fall in the event of an emergency stop and could sustain damage and/or potentially damage anything it falls on.

TROUBLESHOOTING

WARNINGS

• shoX recon is designed for ages 12+
• adult supervision is advised
• the user is responsible for the correct operating & use of this product, make sure to not cause injury to any person or damage to property
• only operate the drone according to the instructions in this manual
• this product can be damaged by contact or collision with a fixed object, accidental damaged is not covered by the warranty
• liability for any damage or loss due to incorrect use lies with the user
• always ensure your flight area is free of all obstacles before taking off
• do not fly the drone closer than 1.5 metres to yourself & others
• do not operate in crowded areas
• do not touch the drones motors during or after flying as they can be hot
• never touch the blades when they are rotating
• remove all butleries from the drones and controllers when not in use
• never overcharge the drone batteries
• never leave unattended while charging
• rechargeable batteries must be removed from the controller before being recharged
• do not attempt to recharge non-rechargeable batteries rechargeable batteries are only to be charged under adult supervision
• do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium} batteries
• do not mix old and new batteries
• only batteries of the same or equivalent type as recommended are to be used
• batteries must be inserted with the correct polarity
• exhausted batteries are to be removed from the controller
• the supply terminals are not to be short-circuited
• the battery in the drone should never be exposed to any form of high temperature or disposed of in a fire
• do not dispose of any parts of the drone or controller in your normal rubbish, all parts should be taken to your local recycling centre

WARRANTY

your shoX recon warranty covers manufacturing defects only. should you encounter an out-of-box failure please return the product in the original packaging with receipt, to the store of purchase so that ii can be assessed.

any evidence of the product being flown, crashed or damaged in any way, or returned incomplete, or without original packaging and receipt, will render the warranty void.

warranty period is 6 months from date of purchase

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>