BOSCH GIC 120 C Professional Cordless Inspection Camera Instruction Manual

GIC 120 C Professional

Original instructions

Safety instructions

**** All instructions must be read and observed.
The safeguards integrated into the inspection camera may be compromised if the inspection camera is not used in
accordance with these instructions. STORE THESE INSTRUCTIONS IN A SAFE PLACE.

Have the inspection camera repaired only by a qualified repair person and only use identical replacement parts. This will ensure that the safety of the inspection camera is maintained.
Do not operate the inspection camera in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Sparks can be created in the inspection camera which may ignite the dust or fumes.
Remove the rechargeable battery from the inspection camera before carrying out any work on the inspection camera (e.g. assembly, maintenance, etc.) as well as when transporting and storing the inspection camera.
Remove the batteries from the inspection camera when not using it for longer periods. The batteries can corrode and self-discharge during prolonged storage.
Do not direct the light beam at persons or animals and do not stare into the light beam yourself (even from a distance).
Check the work area before using the inspection camera. No part of the inspection camera may come into contact with electrical cables, moving parts, or chemical substances. Interrupt the electric circuit of electrical cables running through the work area. These measures reduce the risk of explosions, electric shock, and damage to property.
Wear appropriate personal protective equipment like protective goggles, protective gloves, or a protective mask, if there are substances harmful to health in the work area. Sewers or similar areas can contain solid, liquid, or gaseous substances that are poisonous, infectious, corrosive, or otherwise harmful to
health.
Pay particular attention to cleanliness if you work in areas with substances harmful to health. Do not eat during work. Avoid contact with substances harmful to health, and clean hands and other body parts that could have come into contact with them with hot soapy water after work. This reduces the danger to health.
Do not stand in water if you are using the inspection camera. Working in water poses a risk of electric shock. u Do not open the battery. There is a risk of short-circuiting.
In case of damage and improper use of the battery, vapors may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapors may irritate the respiratory system.
If used incorrectly or if the battery is damaged, flammable liquid may be ejected from the battery. Contact with this liquid should be avoided. If contact accidentally occurs, rinse off with water. If the liquid comes into contact with your eyes, seek additional medical attention. Liquid ejected from the battery may cause irritation or burns.
The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.
When the battery is not in use, keep it away from paper clips, coins, keys, nails, screws, or other small metal objects that could make a connection from one terminal to another. A short circuit between the battery terminals may cause burns or a fire.
Only use the battery with products from the manufacturer. This is the only way in which you can protect the battery against dangerous overload.
Only charge the batteries using chargers recommended by the manufacturer. A charger that is suitable for one type of battery may pose a fire risk when used with a different battery.

Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water, and moisture.
There is a risk of explosion and short-circuiting.
Keep the magnetic accessories away from implants and other medical devices, e.g. pacemakers or insulin pumps. The magnets in the accessories generate a field that can impair the function of implants and medical devices.

Keep the magnetic accessories away from magnetic data storage media and magnetically-sensitive devices. The effect of the magnets in the accessories can lead to irreversible data loss.

Product Description and Specifications

Please observe the illustrations at the beginning of this operating manual.
Intended Use
The digital inspection camera is suitable for inspecting areas
that are dark or difficult to access. It is also suitable for moving and removing small and light objects (e.g. small screws) after fitting the supplied accessories on the camera head.
The digital inspection camera must not be used for medical purposes. It is likewise not intended for removing pipe blockages or installing cables.

Product Features
The numbering of the product features refers to the representation of the inspection camera on the graphic pages.

(1) Handheld device
(2) Magnification button
(3) On/off button
(4) Gallery/settings button (1st level) OK/delete button (2nd level)
(5) Up is Up™ button (1st level) Button for scrolling forwards (2nd level)
(6) Actuator for photo or video recordings or playing videos (gallery mode)
(7) Lighting/brightness button (1st level) Button for scrolling backward (2nd level)
(8) Button for switching between photo and video mode (1st level) Back button (2nd level)
(9) Display
(10) Top flap
(11) Slot for Micro-SD card
(12) Connection for Micro-USB cable
(13) Camera cable
(14) Camera head
(15) Illumination light in the camera head
(16) Camera lens
(17) Rechargeable battery)
(18) Release button
(19) Micro-USB cable
(20) Micro-SD card
(21) Camera connection
(22) Locking mechanism for the camera cable
(23) Magnet
(24) Hook
(25) Mirror
(26) Battery adapter cover
(27) Battery adapter cap
(28) Port

A) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
Display Elements (Selection)

(a) Selected photo or video mode
(b) Status bar
(c) Selected magnification
(d) Selected lighting/brightness
(e) State of charge of rechargeable batteries/non-rechargeable batteries
(f) Symbol for switching between photo and video mode
(g) Symbol for gallery mode/settings mode
(h) Switching between color rendition/black and white rendition
(i) Brightness of display setting
(j) Date/time setting
(k) Time of automatic switch-off setting (auto-off function)
(l) Setting for lighting duration of the display
(m) Current memory space assignment of a Micro-SD card

Technical Data

Smallest bend radius of the camera
cable| mm| 25
Camera head diameter| mm| 8.5
Display resolution| | 320 × 240
Approx. operating time| h| 2B)/6C)
Weight according to EPTA-Procedure 01:2014| kg| 0.64
Dimensions (length × width × height)| mm| 217 × 90 × 49
Environmental conditions| |
– Recommended ambient temperature during charging| °C| 0 to +35
– Permitted ambient temperature during operation D)| °C| –10 to +50
– Permitted ambient temperature during storage without a rechargeable
battery| °C| –20 to +70
– Permitted ambient temperature during storage with a rechargeable
battery| °C| –20 to +50
Recommended rechargeable batteries| | GBA 10,8V…
GBA 12V…
Recommended chargers| | GAL 12.

A) Free of condensation
B) With non-rechargeable batteries
C) With the rechargeable battery at 100 % brightness of the light in the camera head
D) Limited performance at temperatures <0 °C

Assembly

Power supply
The inspection camera can be operated either with commercially available non- rechargeable batteries or with a Bosch lithium-ion rechargeable battery.

Operation with battery adapter (see figure A)
The batteries are inserted into the battery adapter.
The battery adapter is intended only for use in designated Bosch inspection cameras and must not be used with power tools.
To insert the non-rechargeable batteries, slide the cover (26) of the battery adapter into the port (28). Place the batteries into the cover as per the illustration on the cap (27). Slide the cap over the cover until you feel it click into place and it is flush with the handle of the inspection camera.
To remove the batteries, press the release buttons (18) on the cap (27) and pull the cap off. Pull out the cover (26) from inside the port (28).
Always replace all the batteries at the same time. Only use batteries from the same manufacturer and which have the same capacity.

Remove the batteries from the inspection camera when not using it for longer periods. The batteries can corrode and self-discharge during prolonged storage.
Operation with rechargeable battery (see figure B)
Use only the chargers listed in the technical data. Only these battery chargers are matched to the lithium-ion batteries of your inspection camera.

Note: The use of rechargeable batteries unsuitable for your inspection camera can lead to malfunctions or damage to the inspection camera.
Note: The battery is supplied partially charged. To ensure full capacity of the battery, completely charge the battery before the first use.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging process does not damage the battery.
To insert the charged rechargeable battery (17), slide it into the port (28) until you feel it click into place and it is flush with the handle of the inspection camera.
To remove the battery (17), press the release buttons (18) and pull it out of the port (28). Do not use force to do this.

State of charge of rechargeable battery/non-rechargeable battery
If the state of charge of the rechargeable batteries/non-rechargeable batteries is low, the  symbol will first appear in the display. When the symbol is empty,  you have to replace the rechargeable battery/non- rechargeable batteries or charge the rechargeable battery. Inspections are no longer possible.

– Memory space assignment/formatting of Micro-SD card (m)
Status bar
The status bar (b) is shown on the display for approx.
2 seconds each time a button is pressed. It shows:
– The selected recording mode (a)
– Date and time
– The selected magnification (c)
– The selected brightness (i)
– The state of charge of the rechargeable battery/non-rechargeable batteries (e)
Transferring images and videos
Transferring images and videos is only possible with an inserted Micro-SD card (20).
The inspection camera can be connected to a computer using a Micro-USB cable (19), to transfer images and videos.
Note: The USB port cannot be used with Apple products (e.g. MacBooks). Data transfer functions only via the MicroSD card in this case.
A symbol in the display of the inspection camera shows that it is connected to a computer.
The inspection camera is displayed on the computer as an external drive.
The rechargeable battery of the inspection camera cannot be charged via the connection (12).

Connecting a micro USB cable for data transfer
Open the top flap (10) and put the Micro-USB cable (19) into the connection (12) in the correct position.
After the data has been transferred, remove the Micro-USB cable and close the top flap again.

Working Advice
Check the environment that you want to inspect, paying particular attention to obstacles or hazardous areas.
Bend the camera cable (13) so that the camera head can be easily introduced into the environment to be inspected.
Carefully introduce the camera cable.

Adjust the brightness of the camera illumination light (15) so that the image is easily recognizable. When photographing highly reflective objects, for example, you can achieve better results in lower light.
If objects to be inspected look blurred, then reduce or increase the distance between the camera head (14) and the object.
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Store the machine only within a temperature range between
−20 °C and 50 °C. As an example, do not leave the battery in the car in summer.
A significantly reduced operating time after charging indicates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Errors – causes and corrective measures

Error indicator in the display
The camera cable is not fitted| Fit camera cable.
Micro-SD card not or
not correctly inserted| Insert Micro-SD card
and push in all the way.

Maintenance and Service

Maintenance and Cleaning
Do not immerse the handheld device (1) in water or other liquids.
Always keep the inspection camera clean. Clean the inspection camera and all accessories particularly thoroughly after you have worked in areas with substances harmful to health.
Wipe off any dirt using a damp, soft cloth. Do not use any detergents or solvents.
Clean the camera lens (16) in particular regularly and make sure to check for any lint.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com 
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.
Malaysia

Robert Bosch Sdn. Bhd. (220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my

www.bosch-pt.com.my
You can find further service addresses at: www.bosch- pt.com/serviceaddresses
Transport
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. The batteries are suitable for road transport by the user without further restrictions.
When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labeling must be observed. For reparation of the item being shipped, consulting an expert for hazardous material is required. Dispatch battery packs only when the housing is undamaged.  Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Disposal

The inspection camera, batteries/rechargeable batteries, accessories, and packaging should be sorted for environmentally friendly recycling.
Do not dispose of the inspection camera or batteries/rechargeable batteries with household waste.

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>