Polo Leader Electronic PL-620UB Windows Precision Touchpad User Manual
- June 6, 2024
- Polo Leader Electronic
Table of Contents
Polo Leader Electronic PL-620UB Windows Precision Touchpad
Note:
- The Bluetooth-L.E interface is only supported to Windows 10 and 11.
- This touchpad is programmed with Windows Precision Touchpad Protocol to support touchpad features to Windows 10 and 11.
- Warning! Please don’t install an extra Bluetooth driver to Windows 10 and 11.
- Please charge the device’s battery completely before using the first time.
Introductions
MANO-720 UB provides Bluetooth and USB interfaces for wireless and wired connection to Windows 7, 10 and 11; it supports the Windows precision touchpad protocol to meet the specifications of Windows touchpad, it also integrates mouse button and scroll functions for user can manipulate touch-pad and mouse features simultaneously in all applications.
Features
- Compatible with Microsoft Windows Precision Touchpad Protocol.
- Support Bluetooth and USB interfaces.
- Bluetooth connection distance can up to 10 meters or above.
- Ergonomics designed housing to reduce wrist joint injuries effectively.
- Integrates mouse and touchpad feature together.
- Light indicators to display status of mouse button and device connection.
- Built-in rechargeable lithium-ion battery can recharge than 300 time.
Specifications
- Support Microsoft Windows 10,11’s Precision Touchpad Protocol
- Dimensions: 162.5mm x 123.0mm x 6.1~ 9.3mm
- Touch-Area: 7.0 Inch (Diagonal Length Dimensions)
- Interfaces: Bluetooth BLE V5.0 and USB V2.0
- Power Consumption: 20mA±10% @Bluetooth, 30mA±10% @USB
- System Support: Windows 7, 10 and 11
- Weight: 122 gm.
Note: The first time you use this touchpad, it is recommended for you to go to the Windows 10, 11 touchpad settings page to learn the default gesture func-tions and instructions. In this settings page, you can change the cursor speed and the scroll speed to match your operating habits. About others feature settings please refer to the touchpad settings page in Windows 10/11.
Operations
-
Power Switch
Turn power switch to off, touchpad can use USB to connect to a host. Turn power switch to on, touchpad can use Bluetooth to connect to a Windows 10/11 host. -
Pairing Button
Follow below steps to pair Bluetooth to a Windows 10/11 host:
-
Micro-USB Plug:
- Used for USB cable to connect to a Windows host.
- Used for input USB power to charge device’s battery.
-
Mouse Button Indicator
Light is on when a mouse button below is in pressed. -
Bluetooth Indicator
- Blue light is on when touchpad is connected to a host via Bluetooth. . Blue light is flash when the touchpad is waiting for Bluetooth pairing.
-
USB Indicator
Green light is on when touchpad is connected to a host via USB -
Battery Status Indicator
- Red light is flash when the touchpad’s battery power is in low.
- Green light is on when the touchpad’s battery is in charge.
-
Mouse Button Shortcut
Mouse Button shortcut can operate only by 1-finger tap.
Tap a shortcut to make its button to pressed, re-tap it to release. -
Edge Scroll
Put a finger on Edge Scroll, then sliding up/down to operate roll function. -
Mouse Button Zone
The low-corner 2 zones are used for mouse left and right buttons function.
Note:
- Shortcut function is disabled when gesture or cursor moving is operating.
- Tap or gesture operation will make all of mouse button to release.
- Press pairing button above 4 seconds can do the Bluetooth pairing operation.
- After idle for 15 seconds, all of pressed mouse button will to release.
- In Bluetooth connection, touchpad will into sleep mode after idle for 15 minutes.
- Sliding a finger on touch-area a few seconds can wake touchpad up.
Windows 10 Touchpad Settings
Follow below steps can go to the touchpad setting page, and can redefine
gesture function for your favorites. 
Gesture Function
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio com-munications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television recep-tion, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 0.5 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a
separation distance of at least 0.5 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.