Shenzhen Yifeng Intelligent Technology T2a 2-In-1 Wireless Charging Pad User Manual
- June 6, 2024
- Shenzhen Yifeng Intelligent Technology
Table of Contents
2-in-1 wireless charging pad
USER MANUAL
Model: T2a
USB-C Input:9V⎓2A 12V⎓1.5A
Output 1: Phone 15W
Output 2: Watch 3W
After charging the device on the product for 20 seconds, the indicator light
will go out. After the device is fully charged, it will still shut down.
- It is suggested to use 9V 2A, 12V 1.5A adapter.
IMPORTANT SAFETY INSTRUCTIONS
Before Using the unit, please read the user manual carefully
- Do not store device in high-temperature environment, including heat caused by intense sunlight or other forms of heat. Do not place device in fire or other excessively hot environments. Exposure to fire or temperature above 212°F (100°C) may cause explosion.
- Do not use the wireless charger in excess of its output rating. Overloading outputs above rating may result in a risk of fire or injury to persons.
- Do not expose the wireless charger to rain or snow.
- Do not modify, repair or disassemble the unity, if so, please contact the manufacturer.
Switch off the wireless charger when not in use. The wireless charger will automatically switch off when disconnected from its wall charger.
2-in-1 wireless charging pad
Applicable Devices:
- Samsung GalaxyS21 Ultra/S21+/S21/S20+/S20 /Note10+/Note10/S10e/S10/S10+/Note9/S9/S9+
- Samsung Galaxy Note 8/S8/S8+/S7+/S7/S7 Edge /Note5/S6 edge+/S6+/S6
- iPhone 12 Pro max/12 Pro/12,/11 Pro max/ 11 Pro/11/XS max/XS/XR/X/8 Plus/8/SE
- Apple Watch 6/SE/5/4/3/2.
Please Note:
- The Watch Wireless Charging Area supports Apple Watch only
- Please remove your phone case before charging if the thickness> 5 mm, or if the phone case makes your phone size longer than 164 mm.
- Only use certified QC 3.0/PD Charging Wall Adapter to charge the device, do not plug into computer USB port or any other non-certified USB port.
- Place your qi-enabled device accurately in the wireless charging area when charging.
- a QC 3.0/PD adapter is required when charging 2 devices simultaneously or want to have a fast charging effect.
- Make sure to disconnect the device from power when cleaning.
- It is normal and safe to hear a humming noise when very close to the charger. lt means that this wireless charger is adjusting its temperature to achieve a more efficient charging speed.
- If your device can not be fully charged, this may due to high environmental temperature, please recharge after the temperature is lowered. Our charger has temperature control to safe guard your device when charging.
Q&A:
If the LED light flashes and the wireless charging dock doesn’t work how can i deal with this problem?
- Make sure your device supports the Qi wireless charging function before using this wireless charger.
- Check if you use the QC3.0/PD adapter to charge the device.
- Test with other USB cables.
- Check whether your devices’ case comes with metal objects. Magnetic and metal attachments will make an LED flash and prevent charging.
Thank you for choosing our product
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>