SENSITECH T11013100 Temperature Ultra Monitor User Manual

June 6, 2024
SENSITECH

USER MANUAL
For
TEMPLATE ULTRA BLE

NOTICE OF PROPRIETARY PROPERTY
This document and the information contained in it are the proprietary property of Sensitech. It may not be copied or used in any manner nor may any of the information in or upon it be used for any purpose without the express written consent of an authorized agent of Sensitech Inc.

REVISION HISTORY:

REV DESCRIPTION DWN APVD DATE
2 Initial Release JZL TNS 03AUG21
3 Updated Disclaimer; Remove Watermark Draft stamp JZL TNS 16SEPT21
4 Updated FCC and IC Disclosure JZL TNS 20SEPT21
5 Updated Radiation Exposure JZL TNS 23SEPT21

Introduction

Purpose

This document describes the usage of a TEMPLATE ULTRA BLE device.

Scope

The intended audience is valued customers.

Description

The TEMPLATE ULTRA BLE is a BLE-enabled sensor data logger designed for the transportation industry. It is primarily intended to be used to record and store accurate temperature data as well as transmit the data to a Bluetooth- enabled smartphone or tablet device via a mobile application. The device also supports a secondary legacy download mechanism as well utilizing a USB file system to auto-generate a PDF when plugged into a computer.

The following is a brief summary of its features:

  1. BLE 5.1 Enabled
  2. Internal battery
  3. Temperature Sensor
  4. USB for secondary download
  5. LCD Display
  6. User Interface

Manufacturer Information
Company Name: SENSITECH Inc.
Address: 800 Cummings Center, Beverly, MA USA
Importer Information
Company Name: XXXXXXXXXX
Address: XXXXXXXXXXXXX

Radio Frequency Characteristics

1.4.1. Operating Frequencies
2.4GHZ

Output Power Characteristics

1.5.1. Output Power
0 dbm

Physical Appearance

User Interface

The user interface consists of the following:

  1. Three LEDs (red, green, blue)
  2. Two buttons(Start/Stop)
  3. One LCD Display

2.1.1. LEDs
The LEDs are intended to allow quick and easy-to-read status to be conveyed to the end-user. The user can immediately know the status of the unit during startup and operation.
2.1.1.1. System Startup Sequence
During startup, and If configured the Green LED blinks at 1hz for 4 secs.
2.1.2. Buttons
There are two buttons on the device:

  1. Start – a configurable press delay is added, usually configured to be held for three seconds before it starts.
  2. Stop– a configurable press delay is added usually configured to be held for three seconds before it stops.

2.1.3. LCD
There is an LCD on the device:

During Startup, if there is a hardware failure found during the self-test, an X will display on the LCD and the Stop sign will appear.

Using the Device

Starting the device:

To start the device, press the START button. If the Start Key feature is enabled, the START button must be held down for 3 seconds. The device may only be started from sleep mode.

Stopping the device:

There are 2 methods for stopping the device.

  1. To stop the device, press the STOP button. If the Stop Key feature is enabled, the STOP button must be held down for 3 seconds to stop.
  2. In enabled, Plug the Monitor into a USB port on a computer or printer.

Software

This unit reports data over a BLE connection via a mobile app. This data is accessible via several web-based platforms that target various industries. Please contact customer support for more information.

Disclaimers

| RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
---|---
|

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion

| Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas
| A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
| Do not dispose battery along with the household waste.
| There are no user-serviceable parts inside, the battery cannot be replaced by the end-user, and will
result in damaging the device.
|

To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the device.
  2. Increase the separation between the equipment and device.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that my cause undesired operation.
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this
the device could void the user’s authority to operate the device.
5.1.1 FCC Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment.

IC

This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
5.2.1. IC Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment.

CE

The full text of the EU declaration of conformity is available upon request.
© SENSITECH INC.
T11012860 User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals