PRIMAL RC MT-203 Digital Proportional System User Manual
- June 6, 2024
- PRIMAL RC
Table of Contents
DIGITAL PROPORTIONAL SYSTEM
2.4GHZ
MT-203
SYSTEM SPECIFICATIONS
Transmitter
Model: MT-2031T
RF Output Power <10 OmW
Operating Voltage: 4.8 or 6V
Power Supply: 4 Cell /V kallnetNI-CcVNI-MH
Weight: 8oz(227g) with Alkalises
Frequency 2.4GHz| Receiver
Model: MT-203RE
Frequency: 2.4GHz
Operating Vottage:8.0-8AV(Mcd) 6.0-7.4V(Li-poly 2s)
Weight 026oz (7.49)
Dimensions: 1.38 x 1 x 0.55in (35.1 x 25.3 x 14 mm)
---|---
DIGITAL PROPORTIONAL SYSTEM
MT-203T
- CH1(Steering) Trim. Steering neutral adjustments can be made by moving the steering trim lever to the left or right. When you install a servo, always check to be sure the servo is at its neutral position. Adjust the servo horn position and linkage so both are parallel. Be sure the steering trim on the transmitter is at a neutral position.
- CH1(Steering Dual-Rate)DIR: Use this function to adjust the steering travel of your model. If the model understeers while cornering. add steering by rotating the CW side of the DIR knob. When the model oversteers, take away steering by rotating the C.CW side of the DIR knob.
- CH1(Steering)Reverse: If the servo operates in the opposite direction, moving the reverse lever for the servo reversing.
- Low Battery Indicator: If the transmitter battery voltage drops below 4.2V the LED will be flashed.
MT-203RE: Receiver+ESC for 1/18 Car
- CH1(Steering)Output: Connect the servo for steering operation.
- Battery connector: Connects to the battery. Red is a plus. Black is a minus. For Ni-cd battery 5 7cells(6.0 8.4V) or Lithium-Poly battery 2S(7.4V)
- Motor connector: Connect to the motor.
- CH2(Throttle) Operation: Forward reverse and brake are all linear. When switched to reverse operation just return the throttle trigger from the brake position to the neutral position.
- Low-battery&Heat protection: When the battery voltage drops below 5.5V or the FET is overheated. the motor will shut off and the LED will be rapid flash.
MT-203T &MT-203RE Bind:
Binding Process
- Turn the transmitter power on while pressing the bind SW.
- The transmitter Red LED will flash for 20 seconds.
- Plug the battery into the MR-202, then turn on the power while the transmitter LED is flashing.
- When the LED on the receiver unit is steady light, binding is complete.
- When the binding procedure is successful, the LED on the receiver will stay solid red when both the transmitter and receiver are turned on.
MT-203T LED Display
LED ON: Power on
LED Rapid Flash: Battery low
LED Slow Flash: Bind mode
MT-203RE LED Display
LED OFF: Indicates that the power is off or no signal reception
LED ON: Receiving signals
LED Rapid Flash: Battery low or heat protector is detected.
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (I) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>