nocs NS1100 AIR Hybrid Active Noise Cancelling Earbuds User Guide
- June 6, 2024
- nocs
Table of Contents
Personal Sound.
Hybrid Active
Noise Cancelling.
NS1100 AIR
Scan to download the app
To personalize your sound, and control all features you need to download the
Nocs Design App to your iOS or Android device.
Technical Specifications
Features
- Bluetooth 5.0
- Sound Codecs: SBC, AAC codec
- Driver Type: Electrodynamic, 9.2 mm diameter
- Driver Sensitivity: 102 ±3dB
- Impedance: 16 Ohm
- Frequency Range: 20 – 20,000 Hz
- IPX5 – nano-coating (Dust and splash/sweat resistant)
- MEMS Mic: 4 Enabling Hybrid ANC
Inputs and Outputs
USB-A to USB-C cable for charging.
On-Device Controls
1 Multi-function button on each earphone – touch interface.
Battery Life
Up to 8 hours. 30 hours with charging case at moderate volume.
Charging Time
Earphones: approx. 2h
Charging Case (USB-C): 2h
Battery Size Earphones
Right (Primary): 55 mAh
Left (Secondary): 55 mAh
Charging Case
400 mAh
Let’s get you all setup
Quick Start
Place the earphones in the charging case to charge before your first-time use.
Charge the case using the USB-C cable and any 5V/1A power supply. The charging
time is approximately 2 hours.
After use, please place the earphones back into the charging case, it will
turn off automatically and save battery.
When the NS1100 is charging, the LED will light on in red, and off when fully
charged. When the case is in charge, the LED will flash in white, and light on
all 4 LEDs when fully charged.
Introduction
Take the earphones out of the case. The master side of the earphones will
flash the LED white to indicate it’s in pairing mode. Turn on Bluetooth on
your device for searching.
Select “Nocs NS1100 AIR” on the Bluetooth searched device list, the earphones
will connect to your device.
Download the Nocs Design App from App Store or Google Play Store depending on
your device.
Start the App and choose Nocs NS1100 AIR in the list to connect.
Perform the 3 minutes hearing test in the Nocs Design App and activate
Personal Sound.
NS1100 AIR will automatically turn on when it is taken out of the case, and
turn off when placed back into the case.
For manually turning on the NS1100 AIR, please touch and hold the earphones
touch sensor button for 3 seconds, for manually turning off, please touch and
hold the earphones touch sensor button for 5 seconds.
NS1100 AIR remembers previously connected devices. When turned on, NS1100 AIR
attempts to reconnect to previously connected devices.
Bluetooth Pairing
Take the earphones out from the charging case or touch and hold the touch
sensor button for 3 seconds to power on. The LED on the master side of the
earphones will flash white to indicate it’s in pairing mode.
When pairing, please keep the NS1100 AIR and Bluetooth device in a 1-meter
range and make sure the earphones are turned on.
Check the Bluetooth device found list on your device and search for new
Bluetooth devices if you don’t see “Nocs NS1100 AIR” (Bluetooth product name),
and then select the Nocs NS1100 AIR.
The LED will stop flashing when the earphones are successfully paired.
After the first time pairing the earphones and the paired Bluetooth device
will automatically reconnect when available. Turn the NS1100 AIR on by taking
them out from the charging case.
For manually turning on, please touch and hold the earphone touch sensor
button for 3 seconds, for manually turning off, please touch and hold the
earphone touch sensor button for 5 seconds.
TWS Pairing
Triple tap two times on both sides of the earphones to enter into TWS
pairing mode.
How to use the touch control
| Left Earphone | ← |
|---|---|
| Function: | Left Side Operation: |
| ANC mode switch | Single tap |
| Answer / End call | Single tap |
| Previous track | Double-tap |
| Voice activation | Touch and hold for 2 seconds |
| Reject call | Touch and hold for 2 seconds |
| Right Earphone | → |
|---|---|
| Function: | Right Side Operation: |
| Play / Pause | Single tap |
| Answer / End call | Single tap |
| Next track | Double-tap |
| Voice activation | Touch and hold for 2 seconds |
| Reject call | Touch and hold for 2 seconds |
Is there a problem?
Troubleshooting
The earphones are not connected to each other:
Triple tap two times on both sides of the earphones (either one side first or
triple-tap twice on each side at the same time – the sequence doesn’t matter),
then it will re-pair to each other. The pairing list will be cleared and reset
back to default.
If you are having a problem of a stable connection: Try removing the Nocs
NS1100 AIR from the pairing list on your device by selecting “forget” and then
pairing with the device again.
If the earphones don’t turn off when placed in the charging case:
It means the case needs to be charged. Please turn off the earphones manually
and charge your case.
Hardware Reset
Touch and hold any of the earphones for 11 seconds to reset the earphones.
hello@nocsdesign.com
Nocs AB
nocsdesign.com
FCC ID: A48-NS11
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>