Guangdong Bekey Technology AT1682 WiFi Converter Instructions
- June 6, 2024
- Guangdong Bekey Technology
Table of Contents
Guangdong Bekey Technology
AT1682 WiFi Converter
Instructions
Wireless Range
Mobile phone setup
2.4G
-
Plugin your wifi extender and wait for the 30s
Until the lights( 2. 4G ) both on means able to start setting ‘
If Abnormal please reset:
Press and hold the “Reset/WPS” or “Reset” key for 8 seconds and then release it. Wait until the 2.4G lights are on to indicate a successful reset -
Connect your extender SSID
Both are available
NOTE
Please remember to turn off your mobile network data. You have no access to Internet until you finish all setting steps, If your phone prompts that the network cannot be connected, click to continue -
Open your browser web page (Google&Firefox Browser Recommended)
*NOTE
Pis open the browser.
entering 192.168.188.1
in the address bar and visit.
If access fails, please check if the correct SSID(wifi -xx0x) s connected and the mobile data of the phone is turned off. -
Enter the default password: admin
-
Scan and select your host router to connect
-
Enter the password of your host router
*NOTE
Pis make sure of the right password (special characters are not allowed, like,”blank,<,>) -
Set your Extender SSID and password
*NOTE
If you don’t want to modify, you can proceed to the next step -
Check again and confirm the wireless information
*NOTE
After the check, click “Start Connect ” and wait for 30-60s, the extender will connect to the router -
Wait for the repeater to connect to the router successfully.
After the setting is completed. Please check the signal indicator. It is lit up, it menu that the relay in successfully. Please connect to the internal otherwise recommended. Please wait 47 seconds. sohowifi pro-2.4G/sohowifi -
The “Extender” indicator lights on means successful connection.
*NOTE:
-
Reselect and reconnect to your extender wifi
Re-select and reconnect to your extender wifi hotspot (The new wifi name defaults to the original wifi name plus pro-2.4G
Wireless Range
Mobile phone setup
2.4G
-
Plugin your wifi extender and wait for 30s
Until the 2 lights(2.4G ) both on means able to start setting
*If Abnormal please reset
Press and hold the “Reset/WPS” or “Reset” key for 8 seconds and then release it. Wait until the 2.4G lights are on to indicate a successful reset. -
Connect your extender SSID
Both 2.4G
*NOTE
Please remember to turn off your mobile network data. You have no access to Internet until you finish all setting steps, If your computer prompts that
the network cannot be connected, click to continue -
Open your browser webpage (Google &Firefox Browser Recommended)
NOTE
Pis open the browser, enter 192.168.188.1 in the address bar, and visit. If access fails, please check if the correct SSID(wifi -0XXX) is connected.
-
Enter the default password: admin
-
Scan and select your host router SSID
-
Enter the password of your host router
NOTE
Pls make sure of the right password (special characters are not allowed,like,” blank,<,>) -
Set your Extender SSID and password
NOTE
If you don’t want to modify it, you can proceed to the next step. -
Check again and confirm the wireless information
NOTE
After check, click “Start Connect ” and wait for 30-60s -
Wait for the repeater to connect to the router successfully.
After the setting is completed. Please check the signal indicator. It is lit up, it menu that the relay in successfully. Please connect to the internal otherwise recommended. Please wait 47 seconds. sohowifi pro-2.4G/sohowifi -
The “Extender” indicator lights on means successful connection.
** *NOTE
**
Reselect and reconnect to your extender wifi
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.21 Information to the user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>