Zhongshan Yangguo Electronic Technology Smart X 3-Axis Smartphone Stabilizer User Guide
- June 6, 2024
- Zhongshan Yangguo Electronic Technology
Table of Contents
Smart X
Product List
Before use, please check the package carefully as per the product list. In case of missing, please contact the customer service or your agent.
- Phone Stabilizer *1
- Tripod *1
- Type-C Cable *1
- User Manual *1
App and Tutorial
Download App
Please download our official APP for gimbal stabilizer by scanning below QR
code or searching “AOCHUAN” on your mobile app store.
The APP is available for both IOS and Android systems.
https://www.2vm.net.cn/l_1096/163089246193328
Watch tutorial video
Youtube/Facebook/Instagram: Search and follow”AOCHUAN Gimbal”,get product tutorials, and explore the creative world together.
Unfold and fold the gimbal stabilizer
-
Unfold the gimbal stabilizer
Firstly unfold the arm of the SMART X gimbal, then fit your mobile on the clip, next adjust its level. No need to unlock, easy to use. -
Fold the gimbal stabilizer
Unfold the gimbal as per the yellow arrow. Firstly adjust the arm of the gimbal in parallel with the LED display panel, then rotate the mobile clip until it can be buckled in the hole.
Introduction of SMART X
Introduction of the operation panel
-
Instruction of Modes
PF: Semi-follow mode
F: Full follow mode
L: Lock mode
POV: Selfie mode
Battery life instruction
When the battery is 5% left, the PF indicator will continually flash twice in a little while.
-
Joystick: move up and down, left and right
Single-click: switch to PF/F/L/POV mode
Double click: return to the center position
Triple-click: inception -
Hold down: power on/off
Single-click: switch to fill-light of stage 1/2/3/off successively
Double click: check the battery life -
Single-click: camera / video
Double click: switch to horizontal/vertical panel
Battery charging and replacement
Battery charging
Connect the equipped Type-C cable with a power adapter via a USB port and with
a gimbal stabilizer via a Type-C port.
When the LED display is lit up, it indicates charging status. When [ ] symbol
appears on the LED display, it indicates full battery
Battery replacement
The SMART X gimbal uses a magnetic battery cover. To replace Li battery,
please open the magnetic cover and remove the used
battery. 18650 Li-battery can be purchased on AOCHUAN’s official store.
SMART X is equipped with an original AOCHUAN battery. For first use, please activate the battery by fully charging it, so as to ensure its normal use.
Parameters
| Product Size | 26812565mm (unfolded size) |
|---|
15810855mm (folded size)
Product weight| 295g
Maximum carrying weight| ≤250g
Working hours| 7-9 hours
Charging time| About 2.5 hours
Operation voltage| 3.7V
Power input| 5V/2A
Operation temperature| 0℃~45℃
Li-battery| 3.7V/2600mAh
Matched phone size| 55-90mm
Angle precision| 0.1°
Mechanical pan angle| 310°
Mechanical roll angle| 330°
Mechanical tilt angle| 345°
Controllable pan angle| 310°
Controllable roll angle| 330°
Controllable tilt angle| 76°
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Customer Support
Zhongshan Yang Guo Electronic Technology Co., Ltd.
Address: NO.9 Huayuan Road, Xiaolan Town, Zhongshan City, Guangdong, China.
Tel: 400-609-8883
Website: www.yg-free.com