Whipr Base Unit Instruction Manual
- June 6, 2024
- whipr
Table of Contents
Whipr Base Unit
Paddle. Ski. Row +
THE WORLD’S ONLY PORTABLE MULTI-SPORT ERG MACHINE
Whipr Base Unit
Model: EQBSU-U00-BL1 or EQBSU-U00-BK1
Instruction Manual
Includes: Base Unit, Stabilizing Bracket (for door), Strap Anchor, Ground
Anchor, Webbing Strap, Carry Bag(Needs 3 AA Batteries – Not Included)
- Install 3 AAA batteries. Batteries are located in the bottom of the unit. They can be installed by snapping off the plastic cover by pulling on both sides.
- Turn power on by pushing and holding button on the far left (the one with the circle and vertical line in it).
- After turning power on, you will need to select the desired sport mode. To select the mode, you will press the 2nd button on the left (the one with the 3 horizontal lines). You will then press the button in the middle (the one with the circle). The modes will be highlighted on the right. You will push the up or down button to select the desired mode. The options are: ROW, KAYAK, SWIM, OPEN, SUP, SKI. After selecting the mode, press the 2nd button again (the one with the 3 horizontal lines).
- Resistance Mode – should now be selected from the wheel located at the back of the unit (1-10…1 being the easiest and 10 being the most difficult).
- You are now ready to begin your exercise.
- You can reset your workout any time by pressing the middle button (the one with the circle in it).
The Display Stats include the following:
Strokes/Minute, Distance, Time, 500 Meter Split Time, Projected Time, Calories, Average Watts Securing the Unit – some modalities require the Base Unit to be secured. There are 3 ways to secure the unit. Door – Securing the unit by using the attached inflatable anchor that goes under a door. The door should be a standard 3.5cm width door with up to a 2cm gap.
- Stabilizing Bracket needs to be attached to the base unit – this easily can be done by locking the tabs on the bracket into 2 slots located on the bottom corners of Base Unit.
- Slide the Bracket and Inflatable rubber anchor under the door.
- Inflate the rubber anchor by pushing the larger of the 2 rubber balls on the Base Unit. You will need to keep pushing it until the anchor and bracket are fully secure and very tight under the door.
When you are finished and would like to remove the Base Unit from the door crack, you can push the smaller rubber ball and the anchor will deflate. After removing from under the door, the Bracket can be taken off easily by pulling gently and removing from the grooves on the Base Unit.
Strap Anchor – The strap holder can rotate to be horizontal or vertical
- Before attaching the strap anchor, make sure the plastic panel that the bladder folds into is securely attached to the base unit. Also make sure the bladder is evenly placed in the square box(connects by magnets located within the top of the bladder).
- The lug bolts on the strap anchor easily locks into place on the back of the Base Unit.
- Take the loop end of the strap and place through anchor hole.
- Wrap around object.
- Place buckle through loop and tighten..
Ground Anchor
To use ground anchor, put in ground and wrap strap around anchor. See video links also: https://www.youtube.com/watch?v=7fCmaVLTanY https://[whipr.com](http://whipr.com)/collections/whipr-ecosystem/products /whipr-base-unit
FCC DISCLAIMER
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canada IC DISCLAIMER
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
- For WIFI product, it should be added: This equipment complies with FCC’s and IC’s RF radiation exposure limits set forth for an uncontrolled
environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>