Tt Innovation Technology TT2235 Heyday Wireless Headset User Guide

Tt Innovation Technology TT2235 Heyday Wireless Headset User Guide

Wireless Headset

Include

• Wireless headset
• Microphone
• Aux cable
• USB-C charging cable

Pairing

• Power ON using ON/OFF switch.
• Rapid flashing white light, followed by a chime
• Use Bluetooth settings on your device to pair with HEYDAY HEADSET 01
• Slow flashing white light – pairing successful

Indicators

• Red/White Alternating – Bluetooth pairing
• Slow Flashing White – Paired
• Slow Flashing Red – Battery low
• Red – Charging
• White – Charging complete
• Ascending Tones – Powering on
• Descending Tones – Powering off
• Three Rapid Tones – Ready to pair
• Two Rapid High Tones – Paired
• Two Rapid Low Tones – Low battery
• Two Ascending Tones – Max. Volume
• Two Descending Tones – Min. Volume

Controller on Headset

• ON/OFF: Long press “O” button
• Play/Pause: Single click “O” button
• Pick up/Hang up Calls: When calling, single click “O” button
• Reject Call: When calling, long press “O” button
• Volume up: Single click “+” button
• Volume down: Single click “-” button
• Next Song: Long press “+” button
• Previous Song: Long press “-” button

Detachable microphone

• When you need to talk, please insert the microphone into the jack on the Left side
• Please face the microphone hole for better voice effect
• The microphone switch works only when the microphone is installed
• Microphone on: Push the microphone switch up（shown green）
• Microphone off: Push the microphone switch down（shown red）

Works with AUX

• Use the included Aux cable to connect the headset with other device to work in wired mode
• Once plugged with Aux cable, the bluetooth function of the headset will no longer work, until the aux cable is disconnected from the headset

Charging

• Full charge requires approximately 2-3 hours
• Charging is complete when solid white light turns on
• Plug Type-C end of charging cable into charge port
• Plug USB end of charging cable into a DC 5V USB power supply

Troubleshooting and Tips

• If the microphone can’t working properly, check the plug and microphone are correctly installed, and the microphone switch is on
• If the headset are not working correctly, turn them on/off to reset
• If the headset won’t turn on, recharge the battery and try again
• If the headset won’t charge, make sure the supply works, is 5V >1A, and not damaged
• If the headset make no sound adjust the volume
• If the headset make no sound or do not show as an available device, make sure they are not paired to another device, if so, unpair the device and re-pair the desired device
• This device does not have a pairing code. If prompted for one make sure you are connecting to the correct device. If you are, “forget” the device and re-pair.

NOTE:

• Headset will power off if not connect with the other device within 2 minutes.
• Please keep the distance between the connected devices less than 22 feet to ensure working properly

Need some help?

Can’t get it to pair? Not accepting phone calls? Just have a question?

TargetTechSupport.com

Safety

• Do not use near any water source
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth
• Do not bend the headband too much to ensure the service life of the headset and prevent accidental breakage

heyday

FCC ID: 2AVTM-TT2235 Model: TT2235 Input: 5V Max 1A Made in China
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ●Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. Target Corp.Mpls.MN,55403 Phone:1-612-304-6073

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>