Ningbo Everflourish Smart Technology EFEMP410WLUL Cord Extension Set Instruction Manual
- June 6, 2024
- Ningbo Everflourish Smart Technology
Table of Contents
Ningbo Everflourish Smart Technology EFEMP410WL-UL Cord Extension Set
Instruction Manual
Cutout and Mounting Steps
- Select the desired location of a countertop or desktop. If used on a countertop, the device must be at least 10″ from the stove top and other heating sources.
- The selected location must be at least 0.79 inch (20mm) away from the edge of the countertop or similar surface.
- The mounting surface must be between 0.79 inch (20mm) and 2.16 inch (55mm) thick.
Installation Instructions
- Lay blue painter’s tape on the surface of the wood.
- Mark the position of the hole and drill through the tape into the wood. Painter’s tape is a better choice than all-purpose tan tape because it adheres less strongly and is easier to pull off.
- Cut a 3.9 inch to 4.0 inch hole in surface of countertop.
- Feed the power cord through the hole in the countertop first, followed by the main unit, pushing down until gasket rests on countertop.
- Feed the power cord through the locking flange and turn flange counterclockwise until locked in place against the underside of the countertop.
- Plug the main unit into a wall outlet underneath the countertop. To open the pop up socket, firmly press down on the cover. To close the device, push down on the cover until the unit locks back into place.
Technical Specifications
3 receptacles 2P+E 15A
2x USB: type A+C 3.0A with Quick Charger 3.0
Wireless Charger 10W
With overload protection
14AWGx3C SJT PVC cable, length 6ft
15A/125V~, Max.1875W, 60HZ
Use Specifications
Stock and use temperature: 23°F (-5°C) to 104°F (40°C)
NOTE:
- Please read this manual carefully before assembly and save it for reference:
- Only for indoor use;
- Please keep the product in a dry environment, and environment temperature cannot exceed 95°F (35°C)
- Device connected to AC socket must have ground connection.
- If the rating of the appliance (voltage, power, temperature, frequency etc.) exceeds the below SPECIFICATION, it may damage the appliance.
- In case of failure of the product, do not use it again or open it for repair without permission.
- This product cannot be treated as unclassified municipal waste and should be recycled by a separate collection facility.
- Please contact the local government for information about food chain and damage your life and health.
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules. Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Note: this equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 and part 18 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and any other radio device.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Manufacturer: Ningbo EverFlourish Smart Technology Corp., Ltd
Address: 77 Wuxiang East Road, Yinzhou, Ningbo, 315111, China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>