Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light Instruction Manual

June 6, 2024
Gateway Plastic Hardware Lighting

gateway - logo Plastic Hardware Lighting
X77538 WiFi LED Tap Light
Instruction Manual

WIFI LED TAPE LIGHT

Installation Instructions Smart Tape Light
Remote color chasing
Adhesive 3M tape build into back surface
Easy peel and stick installation
Model No.: X77538

IMPORTANT SAFETY INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or
install the product.

PACKAGE CONTENTS:

  • (1)16.4ft tape light
  • (1)Controller
  • (1)Remoter
  • (1)User guide

21967

ASSEMBLY INSTRUCTIONS

Note; the product is designed to be mounted to a smooth, non-moving surface.

  1. Plan out how you will route the tape light (B) onto making sure there are 16.4 ft available If any cuts are to be made following the ‘CUTTING TAPE LIGHT instructions below
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 8

  2. Determine the best location for the controller Peel the adhesive’s protective strip off sticking the Tape light to the mounting surface. See Fig. 2
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 2

  3. Locate the receiver so that the R Receiver ‘is visible to the remote control
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 3

  4. Plug the connection interface of the receiver (C) into tape light(B) and to make full contact, avoid the current cannot passing, resulting in the lighting is not bright
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 4

  5. And then plug the power connection hole of the receiver (C) into a power supply (D) and fully tighten the threaded connector to keep water Out
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 5

  6. Plug power adapter (D) into a wall socket
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 6

  7. use the remote control (A) for independent ON/OFF control of multiple colors presets, or you can switch to any mode you hike on the remote control Please remove the plastic tab from the battery door before use
    Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 7

  8. To replace remote control battery (E), follow directions on the back of the remote control (A) to slide the battery drawer out Replace the battery (+side up), and slide  battery back in

Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - ASSEMBLY
INSTRUCTIONS 8

WARNING:

These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Prod­ ucts should be installed in accordance with these instructions, current electrical codes and/or the current National Electric Code (NEC)

CUTTING TAPE LIGHT

Note: Tape light can be cut once, if needed, at a specific cutting mark as illustrated below. Once the 16.4.ft length is cut, only the end with the connected power lead can be used. The tail end is not usable unless connected with the connector (see the CONNECTING TAPE LIGHT” below).

  1. Determine the nearest cutting line that is best suited for the specific installation. The cutting lines are located every 3.93′ (see figure 1)
  2. Using a pair of side cutters or quality scissors, make sure the cut is square, measured to the nearest cutting increment that will fit in the space. As accurately as possible, double-checking which cutting line is for the space, cut directly along the cutting line (see figure 1)

Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - CUTTING TAPE
LIGHT

WARNING:

  • Disconnect power at source prior to attempting installation

  • This product is not a toy and contains small parts. Close supervision is needed when used near children

  • The remote control contains a CR2025 battery (button battery).
    If swallowed, it can cause severe injury or death in just2 hours. Seek medical attention immediately

  • Do not dispose of batteries in a fire. Batteries may explode or leak. Remove exhausted batteries from the product lease dispose of batteries properly

  • Never fold tape light. Never bend past the bend radius of 60° whether powered off or lighted

  • Never operate tape light while it is coiled on a reel

  • Route and secure cords so that they will not be pinched or damaged in any way. Do not use staples, nails, or other sharp objects to mount the tape hight or cords as this may damage the outer jacket of the product

  • Do not install near or around flammable or corrosive materials. Do not cover product

  • This product is intended for dry-location use only. Do not locate in damp or wet locations or where water may be present

  • When adding additional tape height segments, use only the same tape hight extension segments. Non-Linkable

  • Only use the power adapter included with the kit. Do not operate with any other power supply

  • The National Electrical Code (NEC) does not permit cords to be concealed where damage to insulation may go unnoticed To prevent fire danger do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible for examination. Cords should be visually examined periodically and immediately replaced when damage is noted

FCC Compliance Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

  1. This device may not cause harmful interference
  2. This device must accept any interference received, including interference that may cause undesired operation

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user s encouraged to try to correct the interference by one or more of the following measures

  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and the receiver
  • Connect the equipment into an outlet different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help

This equipment should be installed and operated with a minimum distance of 20 cm between
the radiator and your body.

Maintenance

Do not use chemical solvents or harsh abrasives to clean tape light

QUICK GUIDE TO CONNECT YOUR STRING LIGHTS TO THE TUYAAPP

https://smartapp.tuya.com/tuyasmart

DOWNLOAD THE TUYA APP BY SCANNING THE QR CODE BELOW.
You can also download the T app by search­ ing Tuya” in either the Apple Store or Google Play

REGISTER A TUYA ACCOUNT
Open the Tuya app and tap Register Follow the onscreen instructions to create an account. Sign into your new account once setup

ADD THE DEVICE TO YOUR TUYA ACCOUNT
a) Once you have successfully signed in select Add Device
b) Select Lighting’ from the left-hand side menu and then select ‘Light Source (WL.Fi
c) Select the Wi-Fi network you would like the light string to be connected to. Enter the appropriate password to the desired Wi-Fi network
d) Plug in the light string into an electrical socket. Click and hold the Power’ button on the light controller for 5 seconds until all the bulbs begin flashing. Once flashing, go back on the app and select that you confirm all the bulbs are flashing
e) The app will begin searching for the light string
f) Once the light string appears on-screen select it and then select Done”
g)At this point, you can change the device name to any name you prefer

LINKING THE TUYAACCOUNT TO ALEXA
a) On the Alexa App Home Page, click on the Home page Menu and select Skills and Games
b) Select the magnifying glass icon and type in ‘Tuya
c) Select the Tuya app in the search results
d) Click on Enable to Use”
e) You will be redirected to an account link page Type in your Tuya account and password
f) Once signed-in, tap Link Now to successfully link your Tuya account

Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light -
TUYAAPP

LINKING THE TUYAACCOUNT TO GOOGLE HOME

a) On the homepage of Google Home App, click the button in the upper left-hand corner, select + select ‘Setup device’ under the list of Add and Manage’, and then click Have something already  set up

b) Find ‘Tuya” in the list. In the new window, select your Tuya account’s the region, type your Tuya account and password, then tap Link Now After you assign rooms for devices, your devices will be listed in the Home Control page

Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - GOOGLE HOME
2

Controller instructions

The default setting of the WIFI controller has 1 buttons function in the sequence of RGBW (sequence RGBW+WW for RGB version).
If you want to switch to a different model, follow the steps below, you can choose any model you like and enjoy it

  1. Press and keep5 seconds, and the configuration modes will appear
  2. Turn on the WW lights
  3. Turn on the ww+Cw lights
  4. Turn on the CW lights
  5. Turn on the Cw+WW lights
  6. Single colors darken
  7. 7color jump
  8. 3color jump
  9. 7 color fade
  10. OFF

Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light -
Controller

REMOTE CONTROL OPERATING INSTRUCTIONS:

Gateway Plastic Hardware Lighting X77538 WiFi LED Tap Light - REMOTE
CONTROL

Dimming (Brighten) Or Increase Color. Change Speed.| Dimming (Darken) Or Decrease Color. Change Speed.| 6 Mode Switch.| ON/OFF
Keep Press and keep 5 seconds, and configuration modes will appear.
---|---|---|---
Red| Green| Blue| Cool White
Hot Pink| Prasinous| Dark Blue| Warm White
Orange| Light Cyan| Purplish Grey| CCT Increase
Light Yellow| Natural Purple| Green Yellow| CCT Decrease
Yellow| Cyan| Purple| Music Mode

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals