Shenzhen X Photoelectric Technology X-X54P Projector Lamp User Manual
- June 6, 2024
- Shenzhen X Photoelectric Technology
Table of Contents
Firefly Laser Projector
User Manual
Thank you for your purchase. Please read this manual carefully before operation. It will give you general information for your safety and optimal performance.
What’s in the box
1.Laser light x 1
2.Adaptor x 1
3.Power cord x 1
4.Bracket x 1
5.Ground stake x 1| 6.Remote control x 1
7.Screws x1
8.User Manual x 1
9.Base x 1
---|---
Safety Attention
-Allowing the unit to cool for 30 minutes after 6 hours of the operation will increase the life of the light source
-This is a Class II laser light.
-This product can be used either outdoors or indoors. It is waterproof(Ip65). Do not put this near flammable objects or liquids. Do not stare into the light source
Please only use the power adapter that is included. If an extension cord is
needed, please check that the extension cord s manufactured to the
specifications needed for the environment and application that it is being
used for.
Installation
1) Cable and Plug Adapter: Connect the cable to the plug adapter. Make sure that the 2pin plug is oriented in the right way. The Flat and Keyway need to match otherwise there will be no contact. Screw the connector cap securely.
- Mounting and Positioning: Mount the laser and adjust the angle of the laser
light to your needs: The laser light should be fixed to a solid object, by
inserting it into the soil, attaching it to trees, or by placing it on the
floor or ground. It is essential to be attached securely for a safe
installation. Do not stare into the beam. Be sure that there are no
flammables or explosives nearby.
3)Power adapter: The power adapter should be installed indoors or in a proper outdoor, waterproof outlet.
4)Remote Control: Pull the plastic sheet out of the bottom of the remote before use. (This can be put back in to conserve battery life when the remote is not used for extended periods of time.)
Assembly Steps
Remote Control Instructions
1. Laser light on/off
2. There are two options: Strobe/No strobe
3. Firefly
Blue Nebula Cloud
4. **Auto**switch between Auto Color-changing mode/Manual mode
5. **+** **-**There are three options: Slow, Fast, and Static
6. If you need to use the timer, press the . The light will strobe two times
to show it has accepted the command. Then press the corresponding time you
want to set the timer.
If you want to cancel the timer, press the . The light will strobe twice to
show it has accepted the command.
Eg: Set the timer for2 hours. The laser will turn off after2 hours. The laser
light will then turn on automatically in 22hours.
FCC Caution
§ 15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
§ 15.21 Information to the user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Rating: AC100-240V,50/60Hz CALSS 2 LASER PRODUCT
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>