IMOU IPC-CX2S-C Consumer Camera User Guide
- June 6, 2024
- imou
Table of Contents
Quick Start Guide
Version 1.0.1
1.251.32.17596-000
Package Content
| |
---|---|---
Caned xl| Power Adapter xl| Potted Cade xl
| |
Mottling Pate xl| Mooring Template xl| Mottos Annexe, xl
|
CISG xl| Screw anti-AndicePack xl
Camera Introduction
Disconnect the camera from the power before installation °flaking out its SD card.
Press and hold the reset button for 10 s to reset the camera.
See the table below for definitions of the camera’s LEO behaviors.
LED Indicator Status | Device Status |
---|---|
Off |
- **** Power, QED turned off
- Rebooting after reset
Solid red| Booting
Device malfunction
Flashing red| Network connection failed
Flashing green| Ready for network configuration
Solid green| Operating proudly
Flashing weer and red alternately| Updating firm: iya re
Setting up Camera
Follow the steps below to add the camera to your Imou account
Step 1 Scan the following QR code or search “Imou life” in Google Play or
App Store to download and install the app.
If you already use the app, make sure that you are using the latest version.
Step 2 Launch the app. Then create an account If you are a new user.
Step 3 Connect the camera to the Knife source with the power adapter.
Step 4 After the camera boots up, the LED indicator light flashes green
(wire-free camera) or is on solid green (wired car a).
If the LED indicator status goes wrong, reset the camera.
Step 5 Follow the on-screen prompts to add the camera_ Repeat the adding
process If you have multiple cameras.
Installing Camera
Mae is sure that the mounting surface is strong enough to hold at least three
times the weight of the camera.
Use Mounting Adhesive
Sten 1 Peel off the mounting adhesive and stick it to the bottom of the
camera.
To paste the device firmly, clean and dry the mounting weave advance.
Step 2 Press and hold the device against the installation area fo 10
Seco–Drs and then release.
Step 3 Power on the camera and then adjust its angle property,
Use Mountkg Pin
Step 1 Peel off the mcunorg template and sack It to the desired
installation area
Step 2 Dni holes into them-rang surface as the mounting template marks
and then insert wall anchors as needed.
Step 3 Stage the mounting date to the mounting surface with Included
mounting SCreYES.
Step 4 Put the antra onto the mounting plate and ensure they attract
each other.
Step 5 Pave on the camera and then adjust its angle properly.
FAQ
Q: the device cannot boot up of work as expected?
Check the EEO Micator status lithe It is not in green, press and hold the
reset lo. Eton for 10 s to reset the camera.
Q: How to connect the camera to another WWI network?
- If the camera is saline, select Dots DIMS > Nevadc Cot to change the Wi-fi connection and the App.
- If the camera cs Ohre. reset the camera. and then configure the Calera again.
Q: Connection takes too Song?
- Check if The distance between the camera and the rater, at that between the camera and the WWI PSOre rs both within 5 m (16.4 ft/during the connection.
- Check the NSA config. Raton oi the router: Seim the channel to auto, and the node to 11lign mixed.
Q: When the intro SO card is fug how is the recorded video saved?
When the micro sd card is fug. the system wr7 overwrite the previous recorded
Save the important information in time.
Q: where are the recorded videos sand?
If you have activated the cloud storage and installed a micro 513 card, the
recordings will be both saved to the card and cloud. if the cloud storage is
deactivated, the recordings are saved to the 50 card- ‘videos recorded during
live view or playback is saved on your phone,
Q: The device is offline?
Check the indicator status:
- Solid green: Check whether the router can connect to the Internet If the network is connected, restart the camera_ a Flashing red: Reset the camera, and then configure the camera again.
- Solid red: The camera Is faulty.
http://www.imoulife.com/web/support/help
For more questions, please scan the QR code below or visit: www.irnoulife.com/tweb/support /help
About the Guide
– This manual is for reference only. The operation of the actual product shall
prevail if there is any inconsistency
– All the designs and software are subject to change without prior written
notice.
– All trademarks and registered trademarks mentioned are the properties of
their respective owners.
– Please visit our website or contact your local customer service if there is
any problem when using the device.
– If there is any uncertainty or controversy, we reserve the right of final
explanation.