ENVION TPP240 UV Air Purifier User Manual
- June 6, 2024
- ENVION
Table of Contents
ENVION TPP240 UV Air Purifier
Thank you for purchasing the Therapure® 240 air purifier. With UV light
andcleanable HEPA-Type filtration to clean the air, the Therapure® 240 air
purifier will greatly improve the quality of the air in your home, office or
other environments. We want you to be fully satisfied with your Therapure®
240. That’s why your Therapure® 240 comes with a one-year limited warranty.
Once you’ve experienced the purity of Therapure® 240 air, visit us at our
website to find out more ways to improve the quality of your air and your life
with our premium products and upgrades.
Please be sure to read the following instructions carefully to ensure optimal
performance and safety.
www.envion.com
Therapure® by BONECO North America Corp. P.O. Box 9159
Van Nuys, CA 91409-8291
800.875.8577
SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING: RISK OF ELECTRICAL SHOCK
Safety precautions should always be used when operating this or any electrical
appliance. Decrease the risk of electrocution, electric shock, injury or fire
by reading and following all the warnings below. Use only as described in
this Therapure® 240 manual. To reduce the risk of electric shock, do not
attempt to service the product in any way other than in the manner described
in the “Cleaning & Maintenance” section of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THE AIR PURIFIER.
- This product operates at 120V AC, 60Hz only.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- Do not operate the product in any greasy environment, such as in the kitchen. This product is not intended to filter oil or grease from the air.
- Do not use the Therapure® 240 air purifier in bathrooms or other humid environments. Do not use near fireplaces or in areas where flammable or combustible vapors or products may exist.
- Always unplug the power cord from the electrical outlet when the purifier is not in use, before cleaning, inserting or removing parts or before moving to another location.
- Never run the air purifier unless it is fully assembled.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does no fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
- Always turn off all controls before unplugging the Therapure® 240 air purifier from the outlet.
- Attempting to service the Therapure® 240 air purifier in any way that is not described in this owner’s manual will cause the warranty to be voided and could cause serious personal injury to the user and/or result in considerable damage to the unit.
- Do not place the cord near a heated surface.
- Do not operate this product with a damaged cord or plug. Discard the product or return to an authorized service facility for examination and/or repair.
- Never use the power cord to pick up, carry, drag, pull, or lift the Therapure® 240 air purifier. Do not pull the cord against or around sharp corners and edges. This could result in injury to the user or damage to the cord.
- Always remove the plug from its power outlet by holding onto the plug itself and pulling gently.
- Never pull on the cord itself to unplug it from its power outlet.
- Use care when operating the Therapure® 240 air purifier by keeping all foreign objects, fingers, body parts, hair, loose clothing and jewelry away from openings.
- Never touch the Therapure® 240 air purifier or its plug when your hands are wet.
- The Therapure® 240 air purifier is an electrical appliance. Adult supervision is required when operating the Therapure® 240 in the presence of children.
- To reduce the risk of fire or electric shock, do not use this air purifier with any solid-state speed control devices.
IMPORTANT WARNINGS
UV Lamp Notice
UV Light is harmful to bare skin and eyes and can cause temporary or cleanable
loss of vision. Never look directly at the UV lamp while it is illuminated;
doing so could cause loss of vision! Only view illumination through the window
at the front of the unit. To prevent exposure to ultraviolet light, disconnect
the power to the unit before servicing any part of the Therapure® 240 air
purifier.
UV Lamp Disposal
If the UV lamp breaks, turn off the unit. Do not operate the unit with a
broken lamp. Do not use a vacuum to clean up breakage. Sweep debris into a
plastic bag and dispose of properly. Contact your local waste management
authority for instructions regarding recycling and the proper disposal of old
lamp(s). To order a replacement lamp, call 1.800.875.8577 or go to
www.envion.com.
Mercury Notice
Because the Therapure® 240 contains a light bulb and light bulbs contain
mercury, Envion is required to provide the following warning:
WARNING: This product can expose you to Mercury, a chemical which is
known to the state of California to cause birth defects or other reproductive
harm. For more information visit
www.P65Warnings.ca.gov.
Do not place your used lamp(s) in the trash. Disposal of any item containing
mercury must be in accordance with any hazardous waste disposal or recycling
laws and regulations of your state. This product complies with the maximum
allowabl concentration of ozone of 0.050 parts per million by volume (ppmv)
in a 24-hour period. The Health Canada Guideline 2010 recommends that the
maximum exposure limit, based on an averaging time of 8 hours, is 0.020 ppmv
or less when tested in sealed, controlled room approximately 30 m3 TPP240
PRODUCT BENEFITS
- 24 hr. Timer to set run time.
- Effectively reduces smoke, pollen, dust.
- 3 speed fan setting–lets you select the desired cleaning level.
- ION boost refreshes the air.
MAIN PARTS
- Locking Latch
- Air Inlet Grill
- Cleanable HEPA-Type filter
- UV Lamp Cover
- UV Lamp
- Control Panel
- Speed Button: 3 fan speed settings: (low, medium and high).
- Power Button
- Timer Button
- LED Display
- UV Indicator Light Bar: Lights up when UV feature is turned ON.
- Clean Filter Indicator: Lights up when it’s time to clean the filter. Press Timer + Power Button for 3 seconds to reset filter indicator.
- ION Button
- UV/VOC Button
- Air Outlet Grill
- Base of Unit
OPERATING THE THERAPURE® 240
Before using the Therapure® 240 air purifier, please read the following important information.
Electrical Ratings:
- 120V Setting: 120Vac, 60 Hz
- Power consumption: 55 watts at high fan speed,
- Net weight: 10.3 lbs.
- Dimension (LxWxH): 9.6” x 7.9” x 26.25”
Replacement Parts:
Lamp – TPP2400
Filter – TPP240F
Locate a level surface on which to place the Therapure® 240 air purifier near a 120V outlet (follow warnings in the “SAFETY INSTRUCTIONS” and “IMPORTANT WARNINGS” sections of this manual). Position your Therapure® at least one foo(12 inches) from the wall. Plug in the unit.
Safety
- Do not place near fans.
- Keep both sides of the unit at least 1 foot away from a wall.
- Do not place the unit near curtains.
- Placing the unit close to the source of air pollution is an effective way to improve indoor air quality.
Note:
DO NOT run the Therapure® 240 with a broken filter. Replace the filter if the
filter has a tear or a hole in it. If the filter is damaged or needs
replacement, please visit the Therapure® website at
www.envion.com to order for a replacement filter. Or
call 1.800.875.8577.
Controls/Settings
- Power Control – To operate the Therapure® 240 air purifier,press the “ON/OFF” button to turn on the air purifier, press the button again to turn off the air purifier.
- Timer Control – The Therapure® 240 air purifier can be programmed to turn off after a preset amount of time. Press the “TIMER” button to program the timer. Each press will add one hour up to a total of 24 hours. Keeping the button pressed will automatically increase to 24 hours, 1 hour at a time, after that it will turn back to off.
- ION Generator – Press the ION Generator button to turn on the ions. Press it again to tur off the ions.
- Speed Control – The Therapure® 240 has three different speeds of cleaning, LOW, MED and HI. Press “SPEED” button to cycle the settings and select the fan speed you desire. The speed state will be shown on the LED display.
- +UV Control – Press the UV/VOC control button “UV/VOC” to turn on the UV lamp Press it again to turn off the UV and VOC.
- Clean Filter Indicator Light – The Therapure® Clean Filter Indicator Light will turn on each time the filter needs to be cleaned.
- Reset Filter Control – Press down the “TIMER” and “ON/OFF” button for 3 seconds, the clean filter light will flash 3 times and then the clean filter light will turn off, indicating the unit has been reset.
CLEANING & MAINTENANCE
Keep the Therapure®240 functioning properly by cleaning the Cleanable HEPA-
Type filter every four weeks of use. More frequent cleaning will be necessary
if the unit is located in an area with a high level of airborne contaminants
(excessive amounts of smoke, pet dander, etc.). Exposing the Therapure® 240 to
candle/oil/fireplace soot and smoke is not recommended and will require more
frequent cleaning.
Note: Always make sure the Therapure® 240 is turned off and unplugged
before cleaning.
- Vacuuming will restore performance of the Cleanable HEPA-Type Filter. However, the filter may appear stained. This is normal and does not affect performance in any way.
- Do not use water or any household cleaners or detergents to clean the Cleanable HEPA-Type Filter.
- The inlet grill may be cleaned (after unit is turned off and unplugged) with a vacuum or a slightly damp cloth.
Cleaning the Cleanable HEPA-Type Filter
- Release the inlet grill by pressing on the locking latch (see diagram of Main Parts).
- Remove the inlet grill from the unit as shown below.
- Grasp the left and right frames of the Cleanable HEPA-Type Filter through the indentations on the sides of the filter enclosure and remove the filter.
- To clean the Cleanable HEPA-Type Filter, use the brush or crevice attachment with a vacuum cleaner. Run the attachment along the inlet and outlet side of the filter, cleaning between the crevices as much as possible. Do not use water or an household cleaners or detergents to clean the Cleanable HEPA-Type Filter.
- Once the Cleanable HEPA-Type Filter has been cleaned and checked for any possible damage, replace the filter back in the reverse direction described here. Plug in the unit and hold down Time + Power On button for 3 seconds. The clean filter light will go off and your cleaning maintenance is done.
Cleaning External Surfaces
- Turn off and unplug unit.
- Use a washcloth slightly dampened with a little water and dishwashing soap to wipe the outer case surfaces.
- Do not allow water to slip into the internal parts as this could damage your unit and result in electrical shock and injury to you.
- Allow the unit to thoroughly dry before use.
UV Lamp
The lifetime of the UV lamp is up to 12 months of continuous, effective
operation. After this time, the bulb may remain illuminated, but its
effectiveness is greatly reduced. For maximum effectiveness, please replace
the UV bulb annually.
If the lamp stops functioning or needs replacement, please visit our web site
at www.envion.com to order a replacement lamp. Or
call 1.800.875.8577.
Caution:
- Do not touch the glass part of the lamp. Oil from fingertips will decrease the effectiveness of the lamp.
- Never operate the unit without a filter or with a damaged filter. UV lamp cover must be installed at all times. The UV light from the UV lamp will result in severe damage to eyes and could cause blindness.
UV Lamp Notice Warning:
UV Light is harmful to bare skin and eyes and can cause temporary or cleanable
loss of vision. Never look directly at the UV lamp while it is illuminated-
doing so could cause loss of vision!
Before replacing the UV lamp, make sure the Therapure® 240 air purifier is turned off and unplugged. Let the lamp cool down for 5 minutes before replacing it.
Replacing the UV Lamp:
- Release the inlet grill by pressing on the locking latch (see diagram of Main Parts).
- Remove the two bolts used to fix the UV lamp cover and remove the cover out from the unit.
- Unscrew the old UV lamp from the lamp base of the unit.
- Install the new UV lamp into the lamp base of the unit.
- Install the UV lamp cover with the two bolts on the unit.
- Install the inlet grill on the unit.
TROUBLESHOOTING
ONE-YEAR LIMITED WARRANTY
Your Therapure® 240 air purifier is warranted to be free from defects in
materials and workmanship for one year from the original purchase date. Should
the product have a defect in materials or workmanship, we will repair or
replace it without charge to you (a shipping and processing fee will apply).
To obtain service under warranty, simply call our customer service center
toll-free at 800.875.8577 | M-F 7-4 PST / 7-3 Sat.
This warranty does not cover damage caused by accident, misuse or any use
other than as intended and described in this product manual, or damage
resulting from failure to maintain and clean this product as specified in this
product manual. Thi warranty applies only to the original purchaser of the
Therapure® 240 air purifier.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER
EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties, so
the above limitation may not apply to you. While this warranty gives you
specific legal rights, you may also have other rights which may vary from
state to state.
Contact Info for Warranty Service:
Therapure® by BONECO North America Corp.
P.O. Box 9159 | Van Nuys, CA | 91409-8291
1.800.875.8577 | www.envion.com
© 2019 BONECO North America Corp. All Rights Reserved. Patents Pending.
The energy efficiency of this ENERGY STAR qualified model is measured based on
a ratio between the model’s CADR for dust and the electrical energy it
consumes, or CADR/Watt.
ARBITRATION AGREEMENT
PLEASE READ THIS AGREEMENT CAREFULLY. YOU ACCEPT THE TERMS OF THIS AGREEMENT
BY RETAINING THE PRODUCT(S) SHIPPED IN CONNECTION WITH THIS AGREEMENT (THE
“PRODUCTS”) FOR MORE THAN THIRTY (30) DAYS AFTER RECEIPT. IF YOU DO NOT AGREE
TO THE TERMS OF THIS AGREEMENT, YOU MAY RETURN THE PRODUCT TO COMPANY WITHIN
THIRTY (30) DAYS OF RECEIPT FOR A FULL REFUND. THIS ARBITRATION AGREEMENT
(“AGREEMENT”) CONTAINS A MANDATORY ARBITRATION PROVISION THAT AFFECTS YOUR
LEGAL RIGHTS AND REMEDIES BY PROVIDING THAT DISPUTES BETWEEN YOU AND THE
MANUFACTURER, DISTRIBUTOR AND/OR SELLER OF THIS PRODUCT (COLLECTIVELY,
“COMPANY”), MUST BE RESOLVED THROUGH BINDING ARBITRATION AND NOT IN COURT. IT
ALSO PROVIDES THAT ANY DISPUTE CANNOT BE RESOLVED IN A CLASS ACTION OR OTHER
PROCEEDING WHERE YOU REPRESENT OTHER PERSONS OR OTHER PERSONS REPRESENT YOU,
AND THAT NO CLASS OR REPRESENTATIVE ARBITRATIONS ARE PERMITTED. PLEASE
CAREFULLY READ ALL TERMS IN THIS AGREEMENT.
RESOLUTION OF CLAIMS OR DISPUTES.
Any claim or dispute between you and Company (or any of Company’s subsidiaries
or affiliates) arising out of or relating in any way to the Product or this
Agreement shall be resolved through final, binding arbitration. This
arbitration obligation is reciprocally binding on both you and the Company
and applies regardless of whether the claim or dispute involves a tort, fraud,
misrepresentation, product liability, negligence, violation of a statute, or
any other legal theory. Both you and Company specifically acknowledge and
agree that you waive your right to bring a lawsuit based on such claims or
disputes and to have such lawsuit resolved by a judge or jury.
LIMITATION OF LEGAL REMEDIES.
All arbitrations under this Agreement shall be conducted on an individual (and
not a class-wide) basis, and an arbitrator shall have no authority to award
class-wide relief. You acknowledge and agree that this Agreement specifically
prohibits you and the Company from commencing arbitration proceedings as a
representative of others or joining in any arbitration proceedings brought by
any other person. The parties agree that no class or representative actions of
any type are permitted.
ARBITRATION PROCEDURES.
a. Before instituting an arbitration, if you have any dispute, we strongly
encourage you to contact the Company to try to resolve the matter by calling
800-875-8577, although you are not
required to do so.
b. The arbitration of any claim or dispute under this Agreement shall be
conducted in accordance with the expe-dited procedures set forth in the JAMS
Comprehensive Arbitration Rules and Procedures as those Rules exist on the
date you receive the Product, including Rules 16.1 and 16.2 of those Rules.
These rules and procedures are available by calling JAMS or by visiting its
web site at www.jamsadr.com. The arbitration of any claim or dispute under
this Agreement shall be conducted by an arbitrator who has at least five years
of experience conducting arbitrations.
c. The arbitration of any claim or dispute under this Agreement shall be
conducted in the State of California or the location in which you received
this Agreement. For claims of $10,000 or less, you may choose whether the
arbitration proceeds in person, by telephone, or based only on submissions.
d. The Company shall pay costs for the arbitration of claims, including any
JAMS Case Management Fee and all professional fees for the arbitrator’s
services. The Company shall pay the fees and costs of its own counsel, experts
and witnesses and shall not be able to recoup them from you even if you do not
prevail in the arbitra-tion. Unless otherwise provided by law, you acknowledge
and agree that you shall pay the fees and costs of your own counsel, experts
and witnesses.
CHOICE OF LAW.
The arbitration provisions of this Agreement and any arbitration conducted
pursuant to the terms of this Agreement shall be governed by the Federal
Arbitration Act (9 U.S.C. Secs. 1-16). In this respect, the parties
acknowledge that this Agreement involves a transaction conducted in interstate
commerce. Otherwise, this Agreement and the rights of the parties hereunder
shall be governed by and construed in accordance with the laws of the State of
California, exclusive of conflict or choice of law rules.
SEVERABILITY.
If any provision of this Agreement is declared or found to be unlawful,
unenforceable or void, such provision will be ineffective only to the extent
that it is found unlawful, unenforceable or void, and the remainder of the
provision and all other provisions shall remain fully enforceable.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>