DARK MATTER 4028 Hyper-K Wireless Ultralight Gaming Mouse User Guide
- October 27, 2023
- DARK MATTER
Table of Contents
Hyper-K Wireless Ultralight Gaming Mouse
P/N 44028
Quick User Guide
PACKAGE CONTENTS
1x Hyper-K Wireless Ultralight Gaming Mouse
1x USB Micro Receiver
1x USB Charging Cable
1x Quick User Guide
ONLINE SUPPORT
Monoprice™ is pleased to provide free online support. For order related
issues, contact the Customer Service department through the Live Chat link on
our website www.monoprice.com or via email at
[email protected]
For technical issues, contact the Technical Support department through the
online chat button on our website
www.monoprice.com or by sending an email to
[email protected]
Check the website for support times and links.
CHARGING
-
When the internal battery charge is low, the scroll wheel LED will flash red.
-
Plug one end of the included USB Charging Cable into the mouse, then plug the other end into a USB power source. The scroll wheel LED will flash blue while charging is in progress.
You can use the mouse while it is charging. -
When charging is complete, the scroll wheel LED will flash green. If you then press the DPI Switch, it will change to a solid color corresponding to the selected DPI setting.
WIRED/WIRELESS OPERATION
To use the mouse in wired mode, simply plug one end of the included USB
Charging Cable into the mouse, then plug the other end into an available USB
port on your computer. Wired operation offers better and smoother performance
than wireless mode. If the USB Micro Receiver is not plugged into your
computer, the scroll wheel LED will flash blue during wired operation.
The mouse is automatically in wireless mode when it is not plugged into your
computer. For best results, plug the USB Micro Receiver into an available USB
port on your computer, then ensure that the mouse and the Receiver are as
close as possible to each other, with no obstructions to interfere with the
wireless signal.
DPI INDICATIONS
When not indicating charging or wired operation status, the scroll wheel LED
changes color, depending on the selected DPI setting. The following table
shows the corresponding colors for each DPI setting.
| LED Color | DPI Setting |
|---|---|
| Red | 800 |
| Green | 1600 (default) |
| Blue | 3200 |
| Yellow | 6400 |
| Purple | 12000 |
| Cyan | 16000 |
PRODUCT OVERVIEW
SPECIFICATIONS
| P/N | 44028 |
|---|---|
| Sensor | PixArt® PAW 3335 |
| DPI Settings | 800, 1600, 3200, 6400, 12000, 16000 |
| Scroll Wheel LED Colors | Red, Green, Blue, Yellow, Purple, Cyan |
| Polling Rate | Up to 1000Hz |
| Acceleration | 40g |
| Compatible Operating Systems | Windows® XP/2000/Vista®/7/8/10, macOS® |
| Button Life | 50 million presses |
| Nominal Input Power | 5 VDC, 30mA |
| Battery Capacity | 300mAh |
| Operating Time | Up to 50 hours without LED |
| Charging Time | About 3 hours |
| Dimensions (LxWxH) | 4.9″ x 2.6″ x 1.5″ (126 x 66 x 39 mm) |
| Weight | 2.5 oz. (70g) |
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Modifying the equipment without Monoprice’s authorization may result in the
equipment no longer complying with FCC requirements for Class B digital
devices. In that event, your right to use the equipment may be limited by FCC
regulations, and you may be required to correct any interference to radio or
television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Notice for ISED Canada
This device complies with ISED Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Monoprice™, Dark Matter™, the Dark Matter logo, and all Monoprice logos are
trademarks of Monoprice Inc.
USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum.
PixArt® is a registered trademark of PixArt Imaging Inc.
Microsoft®, Windows®, and Vista® are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other
countries.
Apple®, Mac®, and macOS® are trademarks of Apple Inc., registered in the U.S.
and other countries.