TANNOY Platinum F6/B6 Loudspeaker User Guide
- October 27, 2023
- TANNOY
Table of Contents
TANNOY Platinum F6/B6 Loudspeaker
SELECT PLATINUM F6/B6
2-Way Bookshelf and 3-Way Floorstanding 6.5″ HiFi Loudspeakers
Introduction
Thank you for selecting Tannoy loudspeakers, developed in the UK by our dedicated team of design engineers. These speakers are the choice of discriminating music lovers the world over. Musical excellence is designed into our loudspeakers from the start. Careful selection of the very best components combined with strict quality control procedures in the production process ensures this level of excellence is maintained.
To gain maximum performance from your loudspeakers, please take time to read this document in full before the installation. Loudspeakers are electromechanical devices that ‘run in’ through use; performance will therefore improve after an initial period of 24 hours of use. Once they have been further run in over a longer period, there will be clear enhancement of the stereo imaging, mid-band quality, and bass performance characteristics. We are confident that you will continue to enjoy your new Tannoy loudspeakers for many years to come.
Amplifier Choice
Consult the product specification page as this clearly shows the acceptable power range for the amplifier matching to your speakers. The high peak power handling of Tannoy loudspeakers permits responsible use with more powerful amplifiers.
As with all loudspeaker systems, the power handling is a function of voice coil thermal capacity. Care should be taken to avoid overdriving any amplifier, as this will cause output overload resulting in ‘clipping’ or distortion within the output signal. This will cause damage to the speakers if done for any extended period. Generally, an amplifier of higher power that is running hard, but free of distortion, will do less damage to the loudspeaker than a lower-power amplifier continually clipping. Remember also that a high- powered amplifier running at less than 90% of output power generally sounds a great deal better than a lower-powered example struggling to achieve 100%. An amplifier with insufficient drive capability will not allow the full performance of the loudspeakers to be realized.
Unpacking
To unpack the loudspeakers from their boxes remove tape from the top then fold the flaps right back before inverting the carton and contents. Lift the carton clear of the contents then remove all inner packaging. It is strongly recommended that you store all the packaging to allow protected transportation in the future.
Installation
The F6 floor-standing model comes with rubber feet to minimize resonance and coloration. Ensure that the speaker is placed on level ground to prevent tipping. The B6 bookshelf speakers should be located securely on stands or a shelf in an appropriate position to place the high-frequency unit roughly at ear height when seated in the chosen listening position. Positioning recommendations for stand-mounted speakers can be found under the section entitled Positioning and Fine Tuning.
Connection
The positive (plus) terminal on the amplifier’s left channel (marked + or
colored red) must be connected to the positive HF terminal on the left
speaker. The left speaker is the one on the left as you look at the stereo
pair from your listening position. The negative (minus) terminal on the
amplifier’s left channel (marked – or colored black) must be connected to the
negative HF terminal on the left speaker. Repeat this connection process for
the right speaker. Remember that the positive (+ or red) on the amplifier must
be connected to the positive (+ or red) on the speaker and the negative (- or
black) to negative. Select a signal source, such as a CD player; switch on the
amplifier and slowly turn up the volume control to check that both
loudspeakers are reproducing bass and treble information.
Positioning and Fine Tuning
To get the best results from your new Tannoy loudspeakers, it is worthwhile to spend a little time finding the optimum setup configuration. Begin by angling the speakers towards your chosen listening position, usually, this is on the center line of the room, so that when seated you can just see the inner side panel of each speaker. The front of the loudspeaker should not be obstructed in any way.
The loudspeakers should be located between 1.5 to 4.5 meters (5 ft to 15 ft)
apart – with the listening position set slightly further away than the
speakers are apart. Avoid positioning the loudspeakers in the corners of the
room, as this will have a negative effect on performance. For optimum
performance, we would recommend ideally maintaining a distance of at least 0.5
meters (20 inches) from the rear wall, and 1 meter (39 inches) from the side.
However, there is no absolute right or wrong as it is much down to personal
preference and the differing sizes and acoustic properties of the listening
environment. The speakers may be located close to the rear wall, in which case
bass will be increased at the expense of definition, and stereo soundstaging
will be compromised.
Specifications
SYSTEM
- Frequency response 40 Hz – 20 kHz (-6 dB) 50 Hz – 20 kHz (-6 dB)
- Recommended amplifier power 20 – 150 W 20 – 80 W
- Power handling (IEC) 75 W continuous, 300 W peak 40 W continuous, 160 W peak
- Sensitivity 87 dB (1 W @ 1 m) 86 dB (1 W @ 1 m)
- Impedance 8 Ω
Components
- Transducers
- 1 x 6.5″ (165 mm) LF driver, paper cone
- 1 x 6.5″ (165 mm) MF driver, paper cone
- 1 x 1″ (25.4 mm) HF driver, silk dome diaghragm
- 1 x 6.5″ (165 mm) LF driver, paper cone
- 1 x 1″ (25.4 mm) HF driver, silk dome diaghragm
- Crossover type 3 way 2 way
- Crossover frequency 350 Hz and 2.5 kHz 2.5 kHz
- Type Hard wired passive, low loss
Enclosure
- Type Rear ported reflex
- Connectors 2 x 4 mm 24 ct Tannoy customized binding posts
- Dimensions HWD 1078 x 300 x 235 mm (42.4 x 11.8 x 9.3″) 360 x 230 x 235 mm (14.1 x 9.1 x 9.3″)
- Net weight 17.1 kg (37.7 lbs) 6.6 kg (14.6 lbs)
- Construction 19 mm (3/4″) MDF with plywood internal bracing, heavily damped
- Finish Burgundy/white/black finish with high acoustic transparency zipper grille
Accessories (not included)
Optional mounting stand
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Documents/Resources
TANNOY Tannoy Platinum F6/B6 [pdf] User Guide TANNOY, SELECT, PLATINUM, F6, B6, 2-Way, Bookshelf, and, 3-Way, Floorstanding, 6.5 HiFi Loudspeakers.
Related Manuals/Resources
UniFi Smart Flood Light User Guide Protect Smart Flood Light.
WILLIAMSAV Convey Video Basic User Guide
Convey Video Basic Connection Guide 10300 Valley View Road Eden Prairie, MN
55344 techblue@williamsav.com 800-328-6190.
Caddx Turtle V2 User Guide
Caddx Turtle V2 User Guide Operation Diagram Turtle V2 Quick operation
guide Parameter Connection.
iiglo 1152544 Pet Feeder User Guide
1152544 Pet Feeder User Manual
Manuals+
- home
- privacy
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>