TANNOY VX 15Q-WH 15-12 Inch Power Dual Full Range Loudspeaker User Guide

VX 15Q-WH 15-12 Inch Power Dual Full Range Loudspeaker
User Guide

Important Safety Instructions

**| CAUTION
RISK OF ELECTRIC SHOCK!
DO NOT OPEN!**|
---|---|---

Terminals marked with this symbol carry an electrical current of sufficient magnitude to constitute a risk of electric shock.
Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installations or modifications should be performed only by qualified personnel.
This symbol, wherever it appears, alerts you to the presence of dangerous uninsulated voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user-serviceable parts inside. Refer servicing to qualified personnel.
Caution
To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Caution
These service instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Use only attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.
    Servicing is required when the apparatus has been damaged in any way, such as a power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.  The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

17.  Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU)  and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with  EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.

18. Do not install in a confined space, such as a bookcase or similar unit.

19. Do not place naked flame sources, such as lighted candles, on the apparatus.

20. Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed of at a battery collection point.

21. This apparatus may be used in tropical and moderate climates up to 45°C.

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas,  Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.

Thank you for choosing a Tannoy loudspeaker product for your application. If you would like further information about this or any other Tannoy product, please visit
our website at tannoy.com.

Unpacking the Loudspeaker

Each Tannoy VX Series loudspeaker is carefully tested and inspected prior to shipment. After unpacking, please inspect for any exterior physical damage, and save the carton and any relevant packaging materials in case the loudspeaker again requires packing and shipping. In the event that damage has been sustained in transit notify your dealer and the shipping carrier immediately.

System Requirements – Passive and Bi-amped Loudspeakers

Within the VX Series, system designers can choose from a variety of sizes, power levels, and coverage patterns to suit particular requirements. For extended bass performance,  models with the “.2” designation augment the Dual Concentric LF driver with a second matched LF driver. The “HP” designation indicates extended power handling capabilities, while the “Q” suffix indicates incorporation on the new Q-Centric WaveguideTM (QCW™) for applications requiring an asymmetrical coverage pattern. The QCW  horn can be rotated in a matter of minutes, allowing placement of the 75 x 40-degree pattern with either horizontal or vertical orientation.
VX “HP” and “Q” versions have switchable inputs to allow operation in passive or bi-amp modes.
All other VX versions are full-range speakers operating as passive systems and require only one amplifier channel.
To avoid wasting amplifier power, you should use a heavy-duty speaker cable, with a minimum wire size of 1.5 mm² (16 AWG), and preferably 2.5 mm² (14 AWG) for longer runs. Use larger wire sizes for speakers wired in parallel. For extreme cable lengths, be aware of cable impedance and resistive losses. Always observe the correct polarity.

WARNING:
VX Series loudspeakers can produce high sustained output levels for long periods of time. If users are in close proximity, these levels could lead to permanent hearing damage. Because Tannoy loudspeakers have a natural-sounding, flat frequency response and very low distortion, users may not be aware of the potential hazard. For continuous exposure to high levels, we recommend the use of a sound level meter to ensure noise levels are within safety limits. The meter should be capable of integrating levels over a period of exposure in conformance with noise control standards.

Amplifier Considerations

The VX series loudspeakers are optimized for use with the Lab Gruppen PLM+ series amplifiers or Lake LM series controllers used in combination with Lab Gruppen FP amplifiers. A full range of DSP settings to suit any configuration are provided for download on the Tannoy website. The use of third-party amplification and processing is only advised using the matrix of manual settings as well as the limiter calculator provided on the Tannoy website. VX series loudspeaker enclosures should be driven by high-quality power amplifiers designed for true professional use. Power amplifiers should be capable of delivering long-term broadband power equal to half the loudspeaker’s peak power rating at its stated nominal impedance. The use of underpowered amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters,  crossovers, and equalization points must be set in accordance with the settings provided on the Tannoy website.
This will ensure the optimum sound quality and long-term reliability as well as protection from damage.

Neutrik speakON NL4 locking input connector(s) are provided, allowing options for input and link, passive, and bi-amp operation.

Recommended Amplifier Power

Model| VX 5.2| VX 6| VX 8| VX 8.2| VX 8M| VX 12| VX 12HP / VX 12Q| VX 12.2Q| VX 15HP / VX 15Q
---|---|---|---|---|---|---|---|---|---
Mode| Passive| Passive| Passive| Passive| Passive| Passive| Passive| Bi-amp LF| Bi-amp HF| Passive| Bi-amp LF| Bi-amp MHF| Passive| Bi-amp LF| Bi-amp HF
Impedance| 80| 80| 80| 80| 80| 80| 80| 80| 80| 80| 80| 80| 80| 80| 80
Minimum
Amplifier
Power| Continuous
RMS| _ …
13u w| 100W| 130W| 200W| 130W| 200W| 350W| 350W| 80W| 500W| 350W| 350W| 400W| 400W| 80W
Peak| 520 W| 400 W| 520 W| 800 W| 520 W| 800W| 1400 W| 1400 W| 800 W| 2000 W| 1400 W| 1400W| 1600 W| 1600 W| 800 W

Connections

VX 5.2, VX 6, VX 8, VX 8.2

VX 8M

VX 12

VX 12HP, VX 12Q, VX 12.2Q, VX 15HP, VX 15Q

Mounting and Fixing

Arraying

Small alterations to loudspeaker positions can have the effect of minimizing problematic combing frequencies. Arrays should be constructed so that the individual coverage patterns of each loudspeaker combine with minimal overlap. The design of the VXP cabinet greatly simplifies the creation of effective arrays, allowing seamless wide horizontal coverage using two loudspeakers without the need for tedious experimentation.

By placing the VXP cabinets with the 30-degree angled rear panels together, minimal dispersion pattern overlap is achieved, guaranteeing an extraordinarily smooth transition. In many applications, the 90 or 75-degree dispersion pattern may be sufficient in the horizontal plane. It is also possible to stack the cabinets vertically using the above method  (in a central cluster for example) where greater vertical dispersion is required. As shown in the above diagram, one of the VXP cabinets is inverted to allow the optimum splay angle to be achieved. The grille can be simply removed from this cabinet and be replaced for matching orientation. The grille is held in position by the two fixing screws on the top and bottom lips of the cabinet.

The Tannoy Professional hardware covered in this guide has been designed to offer quick, simple, cost-effective, and secure solutions for mounting specific Tannoy Professional loudspeakers. This hardware has been designed and manufactured with a high safety load factor for its specific role. To ensure the safest possible use of the hardware covered in this guide, it must be assembled in strict accordance with the instructions specified. The information in this Quick Start Guide relating to the assembly and the safe use of these accessories must be understood and followed.

IMPORTANT NOTE: The mounting of a permanently installed sound system may be dangerous unless undertaken by qualified personnel with the required experience and certification to perform the necessary tasks. Walls, floors or ceilings must be capable of safely and securely supporting the actual load. The mounting accessory used must be safely and securely fixed both to the loudspeaker and to the wall, floor or ceiling.

When mounting rigging components on walls, floors or ceilings, ensure that all fixings and fasteners used are of an appropriate size and load rating. Wall and ceiling claddings,  and the construction and composition of walls and ceilings, all need to be taken into account when determining whether a particular fixing arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required, must be of an appropriate type, and must be fitted and used in accordance with the maker’s instructions.

The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly, can potentially expose persons to serious health risks and even death. In addition, please ensure that electrical, mechanical, and acoustic considerations are discussed with qualified and certified (by local state or national authorities) personnel prior to any installation or flying.

Make sure that speaker cabinets are set up and flown by qualified and certified personnel only, using dedicated equipment and original parts and components delivered with the unit. If any parts or components are missing please contact your Dealer before attempting to set up the system.

Be sure to observe the local, state, and other safety regulations applicable in your country. MUSIC Tribe, including the MUSIC Tribe companies listed on the enclosed “Service  Information Sheet”, assumes no liability for any damage or personal injury resulting from improper use, installation, or operation of the product. Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and stable condition. Make sure that, where the speaker is flown, the area underneath the speaker is free of human traffic. Do not fly the speaker in areas that can be entered or used by members of the public.

Speakers create a magnetic field, even if not in operation. Therefore, please keep all materials that can be affected by such fields (discs, computers, monitors, etc.) at a safe distance. A safe distance is usually between 1 and 2 meters.

Technical Specifications

| VX 5.2 (-WH)| VX 6 (-WH)| VX 8 (-WH)| VX8M
---|---|---|---|---
System
Frequency response| 87 Hz – 35 kHz -±3 dB
6S Hz-45 kliz-10 dB| 92 It- 35 kHz ±3 c113
80Hz -45 I:Hz-10dB| 85 Hz – 35 kHz ±3 dB
62 Hz – 45 kHz -10dB| 85 Hz -351tHz -1-3 dB
62 Hz-45 kHz-10 dB
Nominal dispersion| 120° H x 90°V @ -6dB points| 90° conical @ -6dB point| 90°conical -6dEt point| 90e conical -6d13 point
Directivity factor (Q)| 7.3| 5.6| 6.8| 6.8
Directivity index (DI)| 8.6| 7| 7.9| 9.2
Power handling (IEC)
Passive
Bi-amp| 130W continuous, 520 W peak| 100 W continuous, 400 W peak| 130 W continuous, 520W peak| 130 W continuous, 520 W peak
Sensitivity| 90dB(1 W@lm)| 91 dB(1W@1 m)| 92 dB(1 m)| 92 d8(1WrI m)
Maximum SPL
Passive
Bi-amp| 111 dB continuous, 117 dB peak| 111 dB continuous, 117 dB peak| 113 dB continuous, 119dB peak| 113 dB continuous, 119 dB peak
Impedance Passive Bi-amp| 8 Ω
–| 8 Ω
–| 8 Ω
–| 8 Ω
–
Crossover Type| Passive with dynamic HF protection| Passive with dynamic HF protection| Passive with dynamic HF protection| Passive with dynamic HF protection
Components| 1 x 5″ (125 mm) IF driver
1 x 5″ (125 mm) constant directivity
Dual Concentric| 1 x 6″ (150 mm) constant directivity
Dual Concentric| 1 x 8″ (200 mm) constant directivity
Dual Concentric| 1 x8″ (200 mm) constant directivity
Dual Concentric
Enclosure
Connectors| 2x Neutrik speakON’ NL4
1 x barrier strip terminals| 2x Neutrik speakON NL4
1 x barrier strip terminals| 2x Neutrik speakON• NL4
1 x barrier strip terminals| 2 x Neutrik speakON’ NL4
Wiring
Passive Bi-Amp| Pins 1+/ 1- Input, Pins 2+/ 2- Link| Pins 1+ / 1- Input, Pins 2+ / 2- link| Pins 1+/ 1- Input, Pins 2+/ 2- Link| Pins 1+/ 1- Input, Pins 2+/ 2-Link
Dimensions H x W x| 334 x 181 x201mm
(13.1 x7.1 x7.9″)| 334 x 226 x 216 mm
(13.1 x8.9 x 8.5″)| 389 x 281 x 276 mm
(15.3 x 11.1 x 10.9″)| 389 x 281 x 316.7 mm
(15.3 x 11.1 x 12.5″)
Net weight| 4.4 kg (9.7lbs)| 5.0 kg (11.0 Ibs)| &1 kg (17.8 lbs)| 8.6 kg (18.9 lbs)
Construction| 12 mm (1/2″) plywood, vented and
internally braced| 12 mm (1/2″) plywood, vented and
internally braced| 15 mm (1/4″) plywood, vented and
internally braced| 15 mm (1/4″) plywood, vented and
internally braced
Finish| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M6 x 2 yoke bracket inset
(4 mm alien key)
M6 x4 inserts
Compatible with industry
standard brackets| M6 x 2 yoke bracket insert
(4 mm alien key)
M6 x 4 inserts
Compatible with industry
standard brackets
Blanking plate for optional VTH
pole mount| M10 x 2 yoke bracket insert
(6 mm alien key)
M10 x 2 flying inserts
Compatible with industry
standard brackets
M6 x 4 inserts
Blanking plate for optional VIII
pole mount
1 x Integrip carrying handle| MI0 x 3 flying inserts
(portrait mounting)
1 x Integrip carrying handle
Integral pole mount for standard
35 mm poles
Accessories
| Multi-Angle Wall Mount
Multi-Angle Wall Mount-WH
Yoke Horizontal VX 5.21VX 6
Yoke Horizontal VX 52/VX 6 – WH| Multi-Angle Wall Mount
Multi-Angle Wall Mount-WH
Yoke Horizontal VX 52/W 6
Yoke Horizontal VX 52A0( 6 – WH Top Nat| Multi-Angle Wall Mont
Multi-Angle Wall Mount-WH
Yoke Horizontal VX8
Yoke Horizontal VX8 – WH
Yoke Vertical VX8N)(82
Yoke Vertical VX8NX8.2 – WH
VTH Top Hat|
| VX 8.2 (-WH)| VX 12 (-WH)| VX 12HP (-WH)| VX 12Q (-WH)
---|---|---|---|---
System
Frequency response| 80 Hz – 35 kHz ±3 dB
60 Hz-45 kHz-10 dB| 70 Hz – 25 kHz -±3 dB
55 Hz – 38 kHz -10 d8| 80 Hz – 25 kHz -±3 dB
60 Hz – 30 kHz -10 dB| 80 Hz – 25 kHz 1-3 dB
60 Hz – 30 kHz -10 dB
Nominal dispersion| 90′ conical ti -6dB point| 90° conical g -6d B point| 75° conical @ -6dB point| 75° H x40′ V @ -6dB points
Directivity factor (Q)| 8.1| 9.6| 10.1| 13
Directivity index (Dl)| 9.2| 9.8| 10| 11.1
Power handling (IEC)
Passive
Bi-amp| 200 W continuous, 800 W peak| 200W continuous, 800 W peak| 350 W continuous, 1,400 W peak
LF: 350 W continuous, 1,400 W peak
HF: 80 W continuous, 320W peak| 350 W continuous, 1,400 W peak
LF: 350 W continuous, 1,400 W peak
HF: 80 W continuous, 320 W peak
Sensitivity| 93 dB(1Witalm)| 97 d8(1 W641 m)| 97 dB(1 Vigi, 1 m)| 97 d13(1 W @ 1 m)
Maximum SPL
Passive
Bi-amp| 116 dB continuous, 122 dB peak| 120dB continuous, 126 dB peak| 123 dB continuous, 129 dB peak
LF: 124 dB continuous, 130 dB peak
HF: 125 dB continuous, 131 dB peak| 123 dB continuous, 129 dB peak
LF: 124 dB continuous, 130 dB peak
HF: 127 dB continuous, 132 dB peak
Impedance Passive Bi-amp| 8 Ω
–| 8 Ω
–| 8 Ω
8 Ω
8 Ω| 8 Ω
8 Ω
8 Ω
Crossover Type| Passive with dynamic HE protection| Passive with HF protection| Passive / Bi-amp switchable| Passive/ 8i-amp switchable
Components| 1 x8″ (200 mm) LF driver
1 x 8″ (200 mm) constant directivity
Dual Concentric| I x 12″ (305 mm) constant directivity
Dual Concentric| 1 x 12′ (305 mm) constant directivity
PowerDual| 1 x 12″ (305 mm) constant directivity
PowerDual with Q-Centric waveguide
Enclosure
Connectors| 2 Neutrik speakON• N14
1 x barrier strip terminals| 2x Neutrik speakON’ NL4
1 x barrier strip terminals| 2x Neutrik speakON N14
1 x barrier strip terminals| 2x Neutrik speakON• NL4
1 x barrier strip terminals
Wiring
Passive
Bi-Amp| Pins 1+/ 1- Input, Pins 2+/ 2- Link| Pins 1+ / 1- Input, Pins 2+ / 2- Link| Pins 1+ / 1- Input, Pins 2+/2- link
Pins 1+/ 1-1S, Pins 2+/ 2- HF| Pins 1+/ 1- Input, Pins 2+/ 2- Link
Pins 1+ / 1- LF, Pins 2+ / 2- HE
Dimensions 11 x W x D| 591×281 x 276mm
(233 x 11.1 x 10.91| 487 x 371 x 361 mm
(192 x 14.6x 14.2″)| 487 x 371 x 361 mm
(19.2 x 14.6 x 142′)| 487 x371 x 361 mm
(19.2 x 14.6 x 1421
Net weight| 14.8 kg (32.6 lbs)| 16.5 kg (36.3 lbs)| 20 kg (44.0 lbs)| 20 kg (44.01bs)
Construction| 15 mm (34″) plywood, vented and internally braced| 15 mm (34-) ensure/ 18 mm (3/4″) front, plywood, vented and
internally braced| 15 mm 041 enclosure / 18 mm (3/41 front, plywood, vented and
internally braced| 15 mm ensure / 18 mm (141
front, plywood, vented and internally braced
Finish| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M10 x 4 flying inserts
M10 x 2 yoke bracket inserts
2 x Integrip carrying handle
Blanking plate for optional VIH
pole mount| MIO x 8 flying inserts (portrait or
landscape mounting)
M10 x 8 yoke bracket inserts
2 x Intergrip carrying handles
Blanking plate for optional VT11
pole mount
Compatible with industry
standard brackets
M6 x 4 inserts| MIO x 8 flying inserts (portrait or
landscape mounting)
MIO x 8 yoke bracket inserts
2 x Intergrip carrying handles
Blanking plate (or optional VTH
pole mount
Compatible with industry
standard brackets
M6 x 4 inserts| M10 x8 flying inserts (portrait or
landscape mounting)
MIO x8 yoke bracket inserts
2 x Intergrip carrying handles
Blanking plate for optional VTH
pole mount
Compatible with industry
standard brackets
M6 x 4 inserts
Accessories
| Yoke Horizontal VX8.2
Yoke Horizontal VX8.2 – WH
Yoke Vertical VX8NX82
Yoke Vertical VX8NX8.2 – WH
VTH Top Hat| Yoke Horizontal VX12
Yoke Horizontal VX12 – WH
Yoke Vertical VX12NX12.2
Yoke Vertical VX12NX12.2 – WH
VTH Top Hat| Yoke Horizontal VX12
Yoke Horizontal VX12 – WH
Yoke Vertical VX12A0(122
Yoke Vertical VX12MO22 – WH
VIH Top Hat| Yoke Horizontal VX12
Yoke Horizontal 9)(12 – WH
Yoke Vertical VX12NX12.2
Yoke Vertical VX12NX122 – WH
VTH Top Hat
| VX 12.2Q (-WH)| VX 15HP (-WH)| VX 15Q (-WH)
---|---|---|---
System
Frequency response| 70 Hz – 25 kHz -±3 dB
55 Hz – 30 kHz -10 dB| 70 Hz- 25 kHz 1-3 dB
58Hz -30 kHz -10 dB| 70 Hz – 25 kHz ±3 dB
58 Hz -30kHz -10 dB
Nominal dispersion| 75° H x 40°V @ -6dB points| 75° conical g -6dB points| 75° H x 40°V @ -6dB points
Directivity factor (Q)| 13| 9.7| 12
Directivity index (Dl)| 11.1| 9.9| 10.8
Power handling (IEC)
Passive
Bi-amp| 500 W continuous, 2,000 W peak
LF: 350 W continuous, 1,400 W peak
MF/HF: 350 W continuous, 1,400 W peak| 400 W continuous, 1,600 W peak
LF: 400 W continuous, 1,600 W peak
HI: 80 W continuous,320W peak| 400 W continuous, 1,600 W
LF: 400 W continuous, 1,600 W
HF: 80 W continuous, 320 W peak
Sensitivity| 99 dB (1W @1 m)| 99 dB (1 Wgi 1m)| 99dB(1 m)
Maximum SPL
Passive
Bi-amp| 126 dB continuous, 132 dB peak
LF: 123 dB continuous, 129 dB peak
HF: 127 dB continuous, 133 dB peak| 125 dB continuous, 131 dB peak
LF: 126 dB continuous, 132 dB peak
HF: 125 dB continuous, 131 dB peak| 125 dB continuous, 131 dB peak
LF: 126 dB continuous, 132 dB peak
HF: 127 dB continuous, 132 dB peak
Impedance Passive Bi-amp| 8 Ω
8 Ω
8 Ω| 8 Ω
8 Ω
8 Ω| 8 Ω
8 Ω
8 Ω
Crossover Type| Passive I Bi-amp switchable| Passive / Bi-amp switchable| Passive/ 8i-amp switchable
Components| I x 12″ (305 mm) constant directivity PowerDual
with Q-Centric waveguide
1 x 12′ (305 mm) IF driver| 1 x 15″ (380 mm) constant directivity PowerDual| 1 x I (380 mm) constant directivity PowerDual
Enclosure
Connectors| 2x Neutrik speakONNL4
1 x barrier strip tenninals| 2x Neutrik speakO• NL4
1 x barrier strip terminals| 2x Neutrik speakON• NL4
1 x barrier strip terminals
Wiring
Passive Bi-Amp| Pins 1+/ I- Input, Pins 2+ / 2- Link
Pins 1+ / 1- LF, Pins 2+ / 2- HF| Pins 1+/ 1- Input, Pins 2+ / 2- Link
Pins 1+ / 1- LF, Pins 2+ / 2- HF| Pins 1+/ 1- Input, Pins 2+/ 2- Link
Pins 1+ / 1- LF, Pins 2+ / 2- HF
Dimensions H x W x| 781 x 371 x 361 mm
(30.7 x 14.6 x 142′)| 591 x 451 x 421mm
(23.3 x 17.8 x 16.6″)| 591 x 451 x 421 mm
(233 x 172x 16.61
Net weight| 305 kg (67.2 lbs)| 25.5 kg (562 lbs)| 25.4 kg (55.91bs)
Construction| 15 mm (3/4″) enclosure/ 18 mm (14″) front,
plywood, vented and internally braced| 18 mm (3/4″) enclosure / 18 mm (Ye) front,
plywood, vented and internally braced| 18 mm (3/4″) enclosure / 18 mm (1r) front,
plywood, vented and internally braced
Finish| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M10 x8 flying inserts (portrait or  landscape mounting) MIO x 8 yoke  bracket inserts 2 x Intergrip carrying  handles Blanking plate for optional VTH  pole mount| M10 x 8 flying inserts (portrait or  landscape mounting) M 10 x8 yoke  bracket inserts 2 x Intergrip carrying  handles Blanking plate for optional VTH  pole mount Compatible with industry-standard brackets M6 x 4 inserts| M10 x 8 flying inserts (portrait or  landscape mounting) M10 x 8 yoke  bracket inserts 2 x Intergrip carrying  handles Blanking plate for optional VT11  pole mount Compatible with industry-standard brackets Al6 x 4 inserts
Accessories
| Yoke Horizontal VX12.2
Yoke Vertical VX12A9022
Yoke Vertical VX12M(122 – WH
YIN Top Hat| Yoke Horizontal VX15
Yoke Vertical VX15
VTH Top Hat| Yoke Horizontal VX15
Yoke Vertical VX15
VTH Top Hat

Other important information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
2. Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under  “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under  “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

Hereby, Music Tribe declares that this product is in compliance with Directive
2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation
519/2012 REACH SVHC and Directive 1907/2006/EC, and this passive product is not applicable to EMC Directive 2014/30/EU, LV Directive 2014/35/EU.
The full text of the EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark

References

• Music Tribe
• Music Tribe
• Tannoy | Home
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>