BOSS B6RGB 6.5 Inch 165mm 2-Way Amplified Marine/Powersports Roll Cage/Waketower Speaker Pods User Manual
- June 6, 2024
- Boss
Table of Contents
B6RGB
USER’S MANUAL
6.5″ ((165mm) 2-WAY AMPLIFIER MARINE/POWERSPORTS
ROLL CAGE/WAKETOWER SPEAKER PODS
FEATURES BUILT-IN AMPLIFIER, MULTICOLOR ILLUMINATION, AND WIRELESS RF
REMOTE CONTROL
Introduction
Your new B6RGB waketower speakers are high-powred fully-waterproof2 way systems featuring 6.5” drivers and a1″ PEI dome toweeter.
understands that wake tower systems are used in many different types of installations. Our versatile mounting solutions gives you the ability to attach our wake tower speakers to mounting tube diameters of 1.5”- 2” (38 – 51mm)
What is included?
Before you begin installation please check that your system contains the following contents:
- (2) Waketower speakers
- (4) M6 locknuts
- (4) M6 flat washers
- (4) M6x60mm screws
- (4) 2″ mounting aluminum bands for 2″ and 1.875″ installation.
- (4) 1.75″ mounting aluminum bands for 1.75″ and 1.5″ installation.
- (4) 130x14x2mm rubber mounting pads
- (4) 120x14x1mm rubber mounting pads
- (2) 48x30x2mm rubber mounting pads
- (1) Remote control
- (1) Keychain tag
- (1) 3.5mm stereo wire
- (1) Power wire harness
Safety considerations when installing
Please remember that these are heavy products, that will be installed in a boating environment. These vehicles can travel at high speeds and be unstable. So please consider this and use extreme caution.
- Do not mount the speaker in a location were someone may either walk into or strike their head. During a turbulent ride please make sure that you do not loose footing and fall or hit the unit, it may cause injury.
- Secure the wires to the speaker in multiple locations along their route to your audio source so there are no hanging loops of wire. Having unsecure wires in any lighting conditions can cause entanglement and injury.
- Tighten the aluminum bands with rubber inserts using care. Do not over compress the rubber inserts. After installation is complete please recheck all bolts and tight further if needed before taking your boat or vessel out for an audio adventure.
- Do not install these speakers where they may block the view of the pilot and prevent safe operation of the vessel or vehicle.
B6RGB
2-Way Full Marinized
Marine Waketower Speker System
Congratulations on your purchase of a Marinewaketower Speaker System.
It has been engineered to bring you the highest level of performance. Its quality will afford you years of listening pleasure.
Thank your for making your choice for marine audio entertainment!
Specificatioons
Mid Bass Driver: 6.5” (165mm) poly injection cone rubber surround
Tweeter: 1” (25mm) PEI dome tweeter
Crossover network: Built-in
Impedance: 4 Ohms
Frequency Response: 140Hz – 20kHz
Sensitivity: 93dB (1 watt/1 meter)
Dimensions: 7-3/16” (W) x 9-7/8” (H) x 7-5/16”(D) (182(W) x 250 (H) x 186
(D) mm)
Weight (in gift box): 10.8 Ibs (4.9kg)
Amplifier:
Input Impedance: 10kΩ
Frequency Response: 20Hz – 20kHz
Bluetooth:
Version: V5.0 w/ EDR A2DP
Range: 33ft (10m)
Network Name: BOSS Audio Systems B6RGB
All specifications subject to change without notice.
It is strongly recommended that you work with an assistant to install these speakers.
Installation instruction
| STEP1 | STEP2 |
|---|
The two screws can be unbolted to loosen the metal base of the mounting band
to adjust the mounting angle. Make sure to put all components of the mounting
hardwares in a safe location.| The two screws can be unbolted to loosen the
metal base of the mounting band to adjust the mounting angle. Make sure to put
all components of the mounting hardwares in a safe location.
STEP3
| STEP4
Place the front rubber pad on the metal base of the mounting band.| Place the
supplied rubber strip around the cage bar to prevent scratching. Push the
aluminum band over the cage bar. Align the aluminum bands with the metal base
of mounting bands on the waketower speaker.
STEP5
| STEP6
Secure the aluminum bands to the metal base using a pair of M6 x 60mm screws, M6 flat washers, and M6 locknuts as illustrated. The locknut should be installed in to the hex shaped recess on one end of each band. Hand-tighten, allowing just enough freedom to rotate the waketower speaker around the cage bar.| B6RGB waketower speaker installation completed.
Bluetooth connection
Please be sure the Bluetooth is turned on at your device. When the device is in Bluetooth range, it will connet Bluetooth automatically and will be disconnected automatically when it is out of Bluetooth range.
Wire diagram
Remote control functions
-
Power on / off
Tums the illumination on or off -
Dynamic Mode Adjustment (+)
Switches from static to dynamic mode and selects the dynamic mode (up) -
Dynamic Speed Adjustment (-)
Switches from static to dynamic mode and decreases dynamic mode speed -
Static Color Adjustment (+)
Switches to static mode and selects the color (up) -
Static Color Adjustment (-)
Switches to static mode and selects the color (down) -
Brightness Adjustment (-)
Decreases the illumination intensity -
Brightness Adjustment (+)
Increases the illumination intensity -
Dynamic Speed Adjustment (+)
Switches from static to dynamic mode and increases dynamic mode speed -
Dynamic Mode Adjustment (-)
Switches from static to dynamic mode and selects the dynamic mode (down) -
Demo Mode
The unit flashes Red, Green, and Blue.
System dimensions
All specifications subject to change without notice.
BOSS Audio Systems
3451 Lunar Court – Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support: www.bossaudio.com/support
iPod” and iPhone” are registered trademarks of Apple, Inc., in the U.S. and
other countries.
The Bluetooth” word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by BOSS Audio
Systems is under license. Other trademarks and trade names are those of their
respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>