HANNSpree HL162CPB LCD Monitor User Manual

HANNSpree HL162CPB LCD Monitor User Manual

SAFETY NOTICE

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference.
4. Only use attachments/accessories specified by the manufacturer.

WARNING

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only

PRECAUTIONS

• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
• Do not place the monitor on an unstable cart, stand, or table. If the  monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
• Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
• Unplug the unit during a lighting storm or when it will not be used for long period of time. This will protect the monitor from damage due to power surges.
• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
• Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
• Do not attempt to service the monitor by yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
• The wall socket shall be installed near the equipment and shall be easily accessible.

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitor and do not indicate a problem.

• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
• You may find slightly uneven brightness on the screen depending on  the desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours.
• If the screen suddenly flashes erratically or the backlighting fails, please contact your dealer or service center for repair. Do not attempt to repair the monitor yourself.

BEFORE YOU OPERATE THE MONITOR

FEATURES

• 39,62cm / 15.6” Wide Screen TFT Color LCD Monitor
• Crisp, Clear Display
• Ergonomic Design
• Space Saving, Compact Case Design

CHECKING THE CONTENTS OF THE PACKAGE

The product package should include the following items:

LCD Monitor

• Monitor
  

• Protective Cover
  

Cables and User manual

• Type-C Cable
  

• HDMI to Mini HDMI Cable
  

• Type-A to Type-C Cable
  

• Warranty Card
  

• Quick Start Guide
  

• Energy Label
  

SUPPORT HOLSTER STENTS

INSTALL

(For reference only)

POWER

POWER SOURCE:

charge a connected notebook. If the included power adapter is connected to the monitor, then the monitor can.

Note: Power Delivery Output : DC 5V 2A

MAKING CONNECTIONS

CONNECTING TO A PC

You can setup your monitor with the below suggested connections. Ensure your monitor is off during this process.

1. Connect one end of the Type-C cable to the back of the monitor and connect the other end to the computer’s Type-C port.

2. Connect one end of the Type-C cable to the back of the monitor and connect the other end to the Power Adaptor.

3. Connect one end of the HDMI cable (optional) to the back of the monitor and connect the other end to the computer’s HDMI port.

4. Connect the audio cable between the monitor’s audio input and the PC’s audio output (green port).

5. Turn on your monitor and computer
   

6. Earphone

7. Type-C

8. Type-C

9. Mini HDMI

10. Micro-USB

OPERATING INSTRUCTIONS

GENERAL INSTRUCTIONS

Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.

• The power cord should be connected.
• Connect the Signal cable from the monitor to the HDMI card.
• Press the power button to turn on the monitor. The power indicator will light up.
  
  

FRONT PANEL CONTROL

Power Button:

1. Press this button to switch ON of monitor power， Press 3S switch OFF of monitor power.
2. When the monitor is working, Press [Power Button] to enter the source selections.
3. When opening the OSD menu, Press [Power Button] to Return.

Power Indicator:

• Blue: Power On mode.
• Red: Power Saving mode.

MENU / ENTER:

Turn the OSD menu on or Enter to the next menu..

Adjust ╋ －:

1. Adjust Brightness and volume when the OSD is off.
2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated.

NOTES

• Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping box and packing materials, as they will come in handy if you ever have to ship your monitor.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.

HOW TO ADJUST A SETTINGS

BRIGHTNESS/ CONTRAST

BRIGHTNESS| Adjust the brightness value of the display according to your preference. Select 「BRIGHTNESS」 option to adjust the brightness value.
---|---
CONTRAST| Adjust the contrast value of the display according to your preference. Select 「CONTRAST」 option to adjust the contrast value.
ACTIVE CONTRAST| Optimal setting for high contrast images or videos. The dark and light areas of the image are automatically detected, and the contrast is enhanced to provide a clearer, sharper image. Also, you may select the 「ACTIVE CONTRAST」 option.
PRESET MODE| Select the preset mode according to your preference: PC/ MOVIE/ GAME/ ECO [The availability of this function depends upon the selected model]
RESPONSE TIME| Setup the display response time through the Response time function. Available settings are MINIMUM, INTERMEDIATE, and MAXIMUM. [This feature is limited to specific models only.]

IMAGE SETTING

IMAGE RATIO| Setup the image ratio of screen through the aspect ratio function. Available settings are Wide Screen / 4:3
---|---
SHARPNESS| Select the「SHARPNESS」option to adjust the sharpness of the display.

COLOR SETTING

WARM NATURE (6500K) COOL| Adjust the color temperature value of the display according to your preference: WARM /NATURE/ COOL. USER
---|---
USER| Move the cursor to the User option and select it,

1. To adjust the red, enter the「R」 option and adjust the level. 2. To adjust the green, enter the「G」option and adjust the level. 3. To adjust the blue, enter the「B」 option and adjust the level.

LOW BLUE LIGHT| Select the「Low Blue Light」option to adjust the low blue light of the display.

OSD SETTING

LANGUAGE| Select「LANGUAGE」option to change the language of the OSD. Enter the option and select a language.
---|---
TRANSPARENCY| Select「TRANSPARENCY」option to adjust the transparency of the OSD. Enter the option and adjust the level.
H-POSITION| Select「 H-POSITION」option to adjust the horizontal position of the OSD. Enter the option and adjust the level.
V-POSITION| Select「V-POSITION」option to adjust the vertical position of the OSD. Enter the option and adjust the level.
TIME OUT| Select「Time Out」option to set the OSD time out from 5 to 100 seconds. Enter the option and adjust the level.

RESET

RESET| Select the「RESET」option to reset to the monitor’s default setting. This will erase the current settings.
---|---

EXTRA

INPUT SELECT| From the Signal Selection menu, select the「INPUT SELECT」 option to activate the automatic signal search function.
---|---
VOLUME| Select the 「VOLUME」option to change the volume level. Enter the option and adjust the level. [This function applies only to models with incorporated audio.] ● By high volume, risk of hearing damage exists.
MUTE| Select the「MUTE」option to switch the function On or Off.
DDC/CI| Select the 「DDC/CI」option to switch the function On or Off.

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL

TECHNICAL SUPPORT (FAQ)

Q & A FOR GENERAL PROBLEMS 

• Check if the Power Switch is in the ON position.
• Power Cord should be connected

No Plug & Play|

• Check if the PC system is Plug & Play compatible.
• Check if the Video Card is Plug & Play compatible.
• Check if any plug pins on the HDMI connector are bent

The display is too dark or too bright|

• Adjust the Contrast and Brightness Controls.

Picture bounces or a wave pattern is present in the picture|

• Move electrical devices that may cause electrical interference.

The power LED is ON (Blue) but there’s no video or no picture.|

• Computer Power Switch should be in the ON position.
• Computer Video Card should be snugly seated in its slot.
• Make sure monitor’s video cable is properly connected to the computer.
• Inspect monitor’s video cable and make sure none of the pins are bent.
• Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key

Missing one of the primary colors (RED, GREEN, or BLUE)|

• Inspect the monitor’s video cable and make sure that none of the pins are bent

Screen image is not centered or sized properly.|

• Adjust pixel frequency CLOCK and PHASE or press hot-key

Picture has color defects (White does not look white)|

• Adjust RGB color or select color temperature

The screen resolution needs to be adjusted|

• Use Windows 7/ Windows 8 / Windows 10 Right click anywhere on desktop and select Properties>Settings>Screen Resolution. Use the slider to adjust the resolution and click Apply.

No sound is outputted from monitor’s built-in speaker|

• Make sure the sound volume adjustment can be clearly identified. *Make sure the System > Silence option in the monitor menu is on.

Addendum related to Windows 7 / Windows 8 / Windows 10

When you encounter display problem under Windows 7/ Windows 8 / Windows 10, you need to do the following

1. Make sure your PC computer (Hardware requirement) can support Windows 7/ Windows 8 / Windows 10.
2. Make sure your video card can run Windows 7/ Windows 8 / Windows 10.
3. If your video card can support Windows 7/ Windows 8 / Windows 10, need to install the latest Windows 7/ Windows 8 / Windows 10 driver of your video card.

Suggest to do the following:

1. Install the latest Windows 7/ Windows 8 / Windows 10 video driver of your video card.
2. Try to use the recommended display resolution that is supported by the monitor.
3. If the recommended display resolution is not working, try the second recommended display resolution.

58,4cm / 23” (16:9)
60cm / 23.6” (16:9)
62,5cm / 24.6 (16:9)
68,6cm / 27 ” (16:9)
70cm / 27.5” (16:10)| 1920×1200@60Hz| 1920×1200@50Hz

And if you still have display problem after doing the above procedure, please visit Hannspree support and Service Website: http://www.hannspree.eu/en/monitors
Windows is a registered trademark of Microsoft Corporation.

ERROR MESSAGE & POSSIBLE SOLUTIONS

CABLE NOT CONNECTED:

1. Check that the signal-cable is properly connected, if the connector is loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.

INPUT NOT SUPPORT :

Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table.

FACTORY PRESET TIMING TABLE:

MODE| RESOLUTION| HORIZONTAL FREQUENCY (KHz)| VERTICAL FREQUENCY (Hz)
---|---|---|---
1| 640×400 @70Hz| 31.469| 70.087
2| 640×480 @60Hz| 31.469| 59.940
3| 640×480 @70Hz| 36.052| 70.004
4| 640×480 @67Hz| 35.000| 66.667
5| 640×480 @72Hz| 37.861| 72.809
6| 640×480 @75Hz| 37.500| 75.000
7| 720×400 @70Hz| 31.469| 70.087
8| 800×600 @56Hz| 35.156| 56.250
9| 800×600 @60Hz| 37.879| 60.317
10| 800×600 @72Hz| 48.077| 72.188
11| 800×600 @75Hz| 46.875| 75.000
12| 832×624 @75Hz| 49.725| 75.000
13| 1024×768 @60Hz| 48.363| 60.004
14| 1024×768 @70Hz| 56.476| 70.069
15| 1024×768 @75Hz| 60.023| 75.029
16| 1152×870 @75Hz| 68.681| 75.062
17| 1152×864 @75Hz| 67.500| 75.000
18| 1280×720 @60Hz| 45.000| 60.000
19| 1280×960 @60Hz| 60.000| 60.000
20| 1280×960 @75Hz| 74.592| 74.443
21| 1280×768 @60Hz| 47.776| 59.870
22| 1280×768 @75Hz| 60.289| 74.893
23| 1280×1024 @60Hz| 63.981| 60.020
24| 1280×1024 @75Hz| 79.976| 75.025
25| 1360×768 @60Hz| 47.712| 60.015
26| 1366×768 @60Hz| 47.852| 59.964
27| 1440×900 @60Hz| 55.469| 59.901
28| 1440×900 @75Hz| 70.635| 74.984
29| 1400×1050 @60Hz| 64.744| 59.948
---|---|---|---
30| 1600×900 @60Hz| 55.540| 59.978
31| 1680×1050 @60Hz| 65.290| 59.954
32| 1920×1080 @60Hz| 67.500| 60.000

(Video mode)

We ensure that the monitor can be lighted under interlace signal mode, but we can not guarantee the image quality.

APPENDIX

SPECIFICATIONS

LCD Panel

| Driving system| TFT Color LCD
---|---|---
Size| 39.62cm / 15.6” Diagonal
Pixel pitch| 0,17925mm(H) × 0,17925mm(V)
Video| H-Frequency| 30KHz – 83KHz
V-Frequency| 56Hz – 75Hz
Display Colors| 262K
Max. Resolution| 1920 × 1080 @60Hz
Plug & Play| VESA DDC2BTM

Power consumption

| ON Mode| 7W (Typical)
Power Saving Mode| ≤0.5W
OFF Mode| ≤0.3W
Audio output| Rated Power 1.0 W rms (Per channel)
Input Terminal| Type-C HDMI
Maximum Screen Size| Hor. : 344.16mm Ver. : 193.59mm
Power Source| 100–240V 50–60Hz

5V~2.0A

Environmental Considerations| Operating Temp:5° to 35°C Storage Temp.: -20° to 60°C Operating Humidity: 20% to 80%
Dimensions| 356.77 (W)×224.92(H)×10.1(D) mm

14.04 ”(W)×8.85 ”(H)×0.4 ”(D)

Weight (N.W)| 730g (1.6 lb)

The above specification is subject to actual product specification and is subject to change without prior notice

NOTES:
The Maximum Resolution will depends on the display card supporting. Related issue can refer to http://www.hannspree.eu/en/monitors. FAQ section.

This device complies with requirement of EMC directive 2014/30/EU with regard to Electromagnetic Compatibility, and 2014/35/EU and 93/68/EEC with regard to Low Voltage directive.

Socket-outlet shall be near the equipment and shall be accessible.

Trademark Notice:

HANNspree products incorporate High-Definition Multimedia Interface (HDMI TM) technology.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

RECYCLING INFORMATION

We, at HANNspree care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.

These devices contain recyclable materials, which can be re-decomposed and re- integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly encourage you to contact the provided information to recycle this product.

For more information, please visit http://www.hannspree.eu/

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>