GENEINNO T1 Pro Underwater Robot ROV User Manual
- June 6, 2024
- GENEINNO
Table of Contents
- T1 Pro Underwater Robot ROV
- Disclaimer
- I. Introduction
- Safety Guide
- II. User Manual
- 1. APP Download
- 2. Start
- 3. Device Connect
- 4 APP Manual
- Home Page
- Device Operation
- Camera Photo settings
- Setting Menu
- Photos and videos export to PC
- 5. Bluetooth Controller
- III. T1 Pro Special Accessory Guideline
- Underwater Gripper Installation
- Device
- Lateral Thruster
- Using
- External Battery with LED
- IV. Recharge Guideline
- V. Specification
- VI. Maintenance
- Official Media
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
T1 Pro Underwater Robot ROV
Geneinno T1 Pro Underwater Robot
User Manual
V1.2 2021.12
Shenzhen Geneinno Technology Co., Ltd www.geneinno.com
Disclaimer
- Collisions and burns occurred not caused by product quality issues;
- Damage caused by unauthorized modification, disassembly, and main shell opening; Any violations of the official instructions result in injury, disease or property loss of the user;
- Damage or leaking water caused by incorrect installation, usage and operation not following the user manual instructions;
- Damage caused by the customer’s self-repair, assembly and installations not following official instructions;
- Damage caused by unauthorized circuit modifications, improper use of battery packs, non-standard chargers;
- Any damage caused by improper diving activities and underwater filming not following user manual instructions;
- Damage caused by application in harsh environment, such as in strong current, against big waves and etc.;
- Damage caused by applications in a co m p l e x e l e c t r o m ag n e t i c environment or near strong interference source, such as mining areas, transmission towers, high-voltage lines, transformer substations and etc.;
- Device malfunctions caused by applications when interfering with other wireless devices, such as high-power transmitter, image transmission device, Wi-Fi signal interference and etc.;
- Further damage caused by usage when the parts are aged or damaged;
- Damage caused by reliability and compatibility issues when used with non-certified third-party components;
- Damage caused by insufficient discharge when the battery capacity is low, or using battery with quality issues;
- Failure or damage caused by third-party products, including products provided or embedded into T1 Pro by GENEINNO at your request;
- Damage caused by unofficial technology or third-party guidance, such as incorrect product settings, installation, and firmware upgrades;
- Problems caused by operations in sensitive areas (military bases, nature reserves, marine conservation bases and etc.);
- Damage caused by force majeure, such as operation in dark currents, cave collapse, animal hunting and etc.;
- Products or parts which labels or identification codes have been replaced or deliberately daubed;
- Water droplets or water marks may appear on the product. These may be caused by testing after production, and they will not affect the use of the product.
I. Introduction
Geneinno T1 Pro is a light industrial-grade intelligent underwater robot able to dive to 175m depth. CarriedA17/A7 dual cores CPU, support H264/265 ultra-HD 4K video codec, built-in 12-million-pixel class professional camera, 3000lm led fill light in front. built-in dedicated image processing DSP, significantly improve the graphics processing capabilities of various scenes, meantime, the whole machine apply industrial-grade waterproof solution. Max speed underwater is 2m/s. With 2 lateral thrusters, 4 vertical thrusters, Using closed-loop control algorithm, can effectively achieve 360° full attitude motion control, apply functions such as underwater hovering, self- balancing, tilting, fixed depth and orientation, and one-button floating. Has a strong anti-current ability to handle with complex environments. Built-in large-capacity lithium battery guarantees long operating hours. Geneinno T1 Pro also supports omnidirectional scanning sonar, water quality detector, laser ruler, etc. peripheral devices, meets requirements including aquaculture, hull inspection, underwater sampling, salvage, rescue and various underwater exploration and operation.
© 2020-2022 GENEINNO All Rights Reserved.
Safety Guide
1. Please use our product in open water and in an environment with relatively
clear water quality. Try to avoid operating in an environment with too many
aquatic plants, too turbid, or very complicated underwater structures.
2. Make sure there are no dense radio devices or huge metal objects around
the wireless relay and turn on the antenna correctly to avoid affecting the
reception of the wireless relay signal.
3. Please use the official standard charger to charge, please charge in time
after the battery is alarmed, and do not completely use up.
4. After use, please rinse with fresh water and dry in time to avoid seawater
corrosion, and store in a dry and ventilated place.
5. The host is designed with positive buoyancy before installed buoyancy
material. It is recommended not to install buoyancy material in fresh water,
in seawater can be installed buoyancy material, please adjust the installation
position according to the actual balance of the host, subject to the best
balance the host can achieve
6. The wireless relay is designed as low-grade waterproof standards, please
do not use it directly in water or wash it directly with water.
7. Before using/charging, please check all waterproof connectors if any
liquid left such as water, please make it clear before connect. It is
recommended to connect the wireless relay first, then connect to the host, the
system will boot, when finish using, only needs to disconnect the cable and
the host.
8. Please carefully check the motor and propeller make sure it clear before
use, do not put your fingers or other body parts into the thruster net cover
when the product is working, please clean the surface attachments of the motor
and propeller after the machine is off, and wash with fresh water.
9. Aged 16 and below must be under surveillance of adults when use this
product, please control the speed while using, avoid excessively fast movement
in case scratches or damage equipment.
10. Do not place heavy objects on this product, do not expose it to the sun,
and do not store it in a very humid/corrosive environment.
11. Please connect the host and the wireless relay and connect to the APP,
follow the instructions to calibrate the compass, and check that the video,
data transmission and control are normal, then put it in the water. According
to the use environment, should set sea water or fresh water in the APP to
avoid affecting the water depth data.
© 2020-2022 GENEINNO All Rights Reserved.
II. User Manual
1. APP Download
- Scan QR code to download “Geneinno”APP.
- Search “Geneinno” in IOS APP Store or Google Play to download our APP or visit “www.geneinno.com” to download APP from “Support/APP Download” for Android phones.
- Open APP, Please register as a Geneinno member and log in.
2. Start
- Connect the two ends of buoyancy cable separately to T1 PRO and the
wireless relay, and then tighten the fastening nut.
Note: Check whether the O-ring on the waterproof connectors missing or damaged. If missing or damaged, please replace it in time.
3. Device Connect
- Open APP choose T1 Pro, click “Device not connected” icon, jump to the Wi-Fi setting page, find and connect the Wi-Fi named GENEINNO-5G- XXXX/GENEINNO-XXXX, default code is: 88886666
- After Wi-Fi connected, back to APP main interface, click “Device connected” icon to enter the control interface.
© 2020-2022 GENEINNO All Rights Reserved.
4 APP Manual
Home Page
Product Type: Currently selected device model
Menu: APP upgrade, firmware upgrade, Bluetooth handle, about and help
options
Model Display: Current product picture display
Connection Status: Current connection status and entrance of operation
interface
Device: Select the device to be connected
Community: Forum
Underwater City: Underwater picture/video sharing society
My: User Center
© 2020-2022 GENEINNO All Rights Reserved.
Device Operation
Return to homepage: Return to APP main page
3D Real-time posture and compass: Robot navigation attitude and compass
direction display
LED switch and lumen adjust: Control robot LED light switch and
brightness adjustment
Depth lock: Control robot to maintain current depth automatically
Direction lock: Control robot to maintain current direction automatically
Control wheel (Forward/Backward/Left/Right): Control robot forward,
backward, left and right movement
Control wheel(Up/Down/Lateral): Control the robot to dive up/down and
move laterally (lateral movement requires lateral thruster)
Speed gear: Control the robot’s speed, L for low speed, M for medium
speed, H for high speed
Posture recovery: One click to return to level posture
Tilt up/down: The highest tilt-up/down angle is 60°
Camera settings: Settings of image, photo shot and video record
Shutter: Shutter of photo shot and video record
Shot/Record switch: Switch of photo shot and video record
Float to surface : one-click to dive up to water surface
Custom depth : control robot to dive to input depth
Custom heading : control robot to rotate to input direction
Slow start switch : to start robot’s thruster from low speed
Float to surface: Float to the surface with 1-click
Custom depth: Auto-dive to input depth value, in unit of meters
Custom heading: Automatically adjust to the input navigation direction
value, in unit of degree (°)
Slow start switch: speed setting of propeller speed increase, the
propeller accelerates slowly after it is turned on
Auto balance: Auto balance status
Bluetooth controller: Bluetooth controller connection status
Running time: Robot running time in each power on
Depth: Current depth information
Water temperature: Current water temperature information
Live-stream delay: Indicating WI-FI signal status
Battery: Host battery remaining capacity
System settings: System settings, you can view robot information and
modify the host parameters
Camera Image settings
- White Balance: Enable in Auto or Manual mode. In manual mode, could adjust image RGB color style (default value 48/17/33)
- Sharpness Enable in Auto or Manual mode. In manual mode, could adjust image sharpness (default value 100).
- Saturation: Enable image saturation manual set, default value 50.
- Contrast: Enable image contrast manual set, default value 50.
- Brightness: Enable image brightness manual set, default value 50.
- Live resolution Enable live stream resolution switch, default 1080P.
- Image flip: Enable manual image flip in vertical and in horizontal.
- Simultaneous Video: Enable the same shutter for both the main camera and the external camera.
- Restore Default Settings: Restore image default settings.
- SD card format: Erase all files in SD card, including photos and videos.
© 2020-2022 GENEINNO All Rights Reserved.
Camera Photo settings
- Burst: Enable burst mode, capture multiple photos, and could set the burst number and time interval.
- Exposure Time: Enable in Auto or Manual mode. In manual mode, could adjust exposure time (default value 20ms).
- ISO: Enable in Auto or Manual mode. In manual mode, could adjust image ISO value.
Camera Record settings
- Record resolution: Set in 4K or 1080P.
- Video coding: Support video coding in H265/H264, video saved as MP4 format by default.
- File time length: Range from 0-30min, unsegmented division when time length is 0
- Video bit rate: Range from 5MB to 20 MB. Video bit rate could impact video file size and record quality.
- OSD Set watermarks in photos and videos. Watermarks are enabled by default. Could disable them by clicking the icon to dark. It is on when the icon is highlighted.
© 2020-2022 GENEINNO All Rights Reserved.
Setting Menu
- Album: Open the ROV and external camera albums
- Auto-balance: Enable/disable auto balance
- Compass calibration: start compass calibration
- Environment setting: the option for fresh/salt water, select salt water or fresh water, which has effect on depth accuracy only
- US/Japan hand switch US/Japan hand control mode switch
- Unit setting: set unit to the Metric system or British System
- More info: more information display
- User guide: user guidance for starters
- Firmware version: firmware version display
- Storage: display of ROV storage status in the machine
- Restore to factory settings: restore machine to factory settings
Album check and file download
Check and downoad Photos and videos on Mobile device
Press “Album” icon to enter the ROV and local album, to check and save files, could delete or download multiple photos and videos by long press.
Photos and videos export to PC
Windows: First, connects your PC to Geneinno T1 Pro WIFI, then open a browser
on PC,
enter http://192.168.8.8/media to enter the device file system. Photos are in
the photo storage folder, Videos are in the video storage folder. Right click
on the file and click `Save as’to download the selected files. Mac:
The Mac connects to Geneinno T1 Pro WIFI, and then open the Finder application
on the Mac. After opening the application, press the command+K key on the
keyboard and enter SMB:// 192.168.8.8 in the server address, then enter the
storage folders to download files.
5. Bluetooth Controller
a. Switch On: Flip the left switch to “On”, hold the Home button (2 seconds)
till LED1 and LED2 are flashing, controller is power;
b. Controller connection: After the controller enters the connection mode,
open the menu on the right side of the APP homepage, choose “Bluetooth
Controller “, click to search Bluetooth controller , it can find the Bluetooth
controller (GENEINNO-XXXX), click “Connect”, after the connection is
successful, the controller LED1/2 will always be on;
c. Switch Off: Flip the left switch to “Off”, controller will power off. If
the controller is not connected for 3 minutes after power on, the controller
will automatically shut down; after 5 minutes without any operation since
Bluetooth controller connected, the controller will automatically shut down.
d. Recharge: Pull down the right joystick of the Bluetooth controller , when
LED1/2 become off, the controller is in low battery state and needs recharge,
LED1/2 are always on when charging. When LED3/4 are flashing, LED3/4 are
always on, the controller is fully charged.
III. T1 Pro Special Accessory Guideline
Accessory Buoyancy Block Installation
- Align the mounting hole with the hole on bracket, with the arrow of buoyancy block upward.
- Install the wing screw through the hole, insert from the outside to the inside, and tighten the nut by hand.
Note: External battery needs 4 blocks; other devices do not need to install buoyancy blocks.
Underwater Gripper Installation
- Match the mounting bracket of the underwater gripper to the mounting hole at the bottom of the host, and fix with screws.
- Insert the connector of the underwater gripper into the extension port, and tighten it clockwise.
Device
After underwater gripper plugged in, APP will automatically identified and showing the icon on the interface, it can operate by click the icon.
© 2020-2022 GENEINNO All Rights Reserved.
Lateral Thruster
Installation
-
Unscrew the sealing metal cover of the extension port of the intelligent
underwater robot counterclockwise. Match the slot of thruster to the slide rail in the bottom of the host, slide the thruster according to direction indicated by the arrow. -
Fix by screws when it is in right position.
-
Insert the connector of the thruster into the extension port . Tighten it clockwise.
Note: The connector has an anti-reversal insertion design, please pay attention when inserting, please do not rotate when inserting, to avoid damage to the pin and its internal structure.
Using
- Install and connect the Lateral Thruster to underwater robot first, and then power on the robot. Use a tablet or smart phone to connect, and enter the control page in the Geneinno APP.
- Operate the right joystick to control the horizontal movement, the left and right direction is the movement direction of the T1.
External Battery with LED
Installation
-
Unscrew the sealing metal cover of the waterproof connector of the
intelligent underwater robot counterclockwise. Match the slot of battery to the slide rail in the bottom of the host. Slide the battery according to direction indicated by the arrow. -
Push the tail lock to the right to lock the position of the support, the bearing does not move back and forth.
-
Push the lock in place, install the screws to locate.
-
Insert the connector of the battery into the waterproof connector. Tighten it clockwise.
Note: The connector has an anti-reversal insertion design, please pay attention when inserting, please do not rotate when inserting, to avoid damage to the pin and its internal structure.
© 2020-2022 GENEINNO All Rights Reserved.
IV. Recharge Guideline
- You can check the battery information of the host on the operation interface, also can be checked by the battery indicator light on the wireless relay. Please charge in time when the battery is low, use the standard charger and connector to charge the host, charging time is about 3 hours, wireless relay is about 2 hours. The indicator on charger showing red light when it’s charging, turn green when it finish charge.
- Charging should be in the dry place on shore, please do not let the charging connector come into contact with water.
- Please use the standard dedicated charger to charge the external battery.
-
Underwater robot Charging: Connect the charger connector to the host signal/charging port tightly.
-
Wireless Relay Charging: Connect the charger connector and the wireless relay signal/charging port tightly.
-
External Battery with LED Charging: Connect the charger connector to the external battery connector with the special charger tightly. For charging the external battery with LED, please use the standard dedicated charger only. Note: The special charger for external batteries can only charge external batteries, and is not allowed to charge any other devices.
© 2020-2022 GENEINNO All Rights Reserved.
V. Specification
Wireless Relay
Wi-Fi Frequency
|
5GHz+2.4GHz
Antenna
|
Dual antenna
Battery Capacity
|
10.8V/3200mAh/34.56Wh
Working
|
6H
Charging Time
|
3H
App Operation
OS
|
IOS 9.0 or above and Android5.0or
Underwater Gripper
Gripping Force
|
6kg/60N
Maximum Opening Distance
|
60mm
Total Length
|
559mm
Length
|
397mm
Weight
|
660g(air) 120g(water)
Note: with buoyancy material
External Battery with LED
Dimensions
|
472mm*φ36mm
Weight
|
1650g(air), 400g(water)
Battery Parameters
|
4400mAh/97.68Wh/22.2V
Battery Life
|
4h
Charing Time
|
6h
Lateral Thruster
Dimensions
|
112mm*φ78mm
Weight
|
205 g
Maximum
|
thrust output 1.2kg
Maximum
|
Current 3.8A
VI. Maintenance
1. After each use in sea water, please soak the underwater robot in fresh
water for at least 1 hour and run it in fresh water for 10 minutes
2. Keep each port and connector dry and clean, always tighten the protective
cover if necessary. Salt and humidity will corrode the conductors of the
connectors. Please wash with running water, and use absorbent cotton or
handkerchief to wipe off the excess water.
3. After each use, check whether the propeller is entangled with seaweed,
fishing line and other foreign objects. Start the fuselage and check whether
the propeller can rotate normally.
4. Rinse the sand and gravel regularly, soak the underwater robot in fresh
water for at least one hour, and shake the underwater robot upside down to
drain the sand and gravel from the drainage holes until clear water flows out.
5. Check the buoyancy cable regularly. If it is found to be worn or broken,
please replace it in time.
6. Please store the underwater robot in a dry environment with a temperature
range of 5°C to 25°C.
7. If you need to store the machine for a long time, please keep the battery
level between 50%-60%. Please keep the battery level between 50% and 60% if
you charge it every 90 days. If the storage time is more than 90 days, you
must recharge it. If you don’t charge it in time, it may cause the battery to
be over-discharged and damaged. This kind of damage is unrecoverable.
After-sale service
More information please check in Geneinno APP Help selection. If you need
other after sales support or technical issue, please contact
support@geneinno.com or check our website “Service & Support”,
https://www.geneinno.com/support This manual is subject to update without
prior notice
© 2020-2022 GENEINNO All Rights Reserved.
Official Media
Shenzhen Geneinno Technology Co.,LTD www.geneinno.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>