JastexM JLM1-2000 OBD Tracker Instructions
- June 6, 2024
- JastexM
Table of Contents
von-S51 ⌊von Series⌋ ****
JastecM Co Ltd 15948439
www.iastecm.com
Instruction
Please read this manual carefully before use. We won’t take any responsibility for any consequences caused by the user’s negligence by not following the instruction.
Please note
- The warranty does not cover mechanical or electric damages resulting from drowning
- The warranty does not cover the device that has been tampered with by the Warranty beneficiary or any other person in any way. including reconfiguration repair wilful constructional variations modifications and adjustments
- Do not either attach or detach the device while the engine is on
- Beware of chemical products
- Proper service temperature is between -20-•70t
- Do not apply any physical impact to the device and cable
- Please apply rated voltage
- Please park the vehicle in a state place for installation
- Please beware of surrounding while attachinmn giclotaching a device for your safety
- Please keep checking the device attached regularly for service Continuity
- The device’s standby power may affect your vehicle battery condition
Specification
| Processor | 32Bit ARM Cortex-M4(1024KB Flash. 192KB SRAM |
|---|---|
| Memory | Internal Memory 8MB |
| Status | 3-LEDs Indicator (ECU, NETWORK, GPS) |
| Protocol | ISO 9141-2,150 14230-4(KWP-2000), ISO 15765-4(CAN) |
| Interface | SAE J1962 Standard OBD-II 16PIN Connector |
| Support | SAE J1979 Mode $01-$0A |
| Network | LTE Cat.M1 B2,B4,85,812,B13,B25 |
(B2 – Tx: 1850-1910MHz,Fax: 1930-1990MHz)
(B4 – Tx: 1710-1755MHz,Rx: 2110-2155MHz)
(B5 – Tx: 824-849MHz,Rx 869-894MHz)
(B12 – Tx: 699-716MHz,Rx 729-746MHz)
(B13 – Tx: 777-787MHz,Rx 746-756MHz)
(825 – Tx: 1850-1915MHz, Rx 1930-1995MHz)
SIM Type| Embedded SIM (MFF2 Type)
GPS| Modem Built-in GPS, GPS, GLONASS (GPS: 1575.42MHz) (GLONASS:
1597.5-1605.8MHz)
Sensor BMX160, 9-axis Accelerometer + Gyroscope+ Magnetometer
Voltage| DC 12V – 24V
Consumption| Max Power : s4000mW, Sleep : s60mW
Dimensions| 46mm(W)x 25mm(D) x 65mm(H)
Weight| 44g
Dperating Temp -20 – +70°C
Storage Temp| -40 – +80°C
LED Statue
T he lowest order of priority is indicated for multiple statuses
Function| Status|
UI
---|---|---
RED
(ECU)| Y.GREEN (Network)| BLUE
(GPS)| Beep
Boot Sequence| Device Booting| ON| ON| ON|
Device Booting Complete| OFF| OFF| OFF|
OBD| Engine OFF (RPM Under 300)| Blink (0.5s)| | | x
Engine ON (RPM over 300)| ON| | | X
OBD Connection Error
(Ps! Setting Error or ECU Not Response)| Blink (1s)| | | X
Key-Fob or Periodic wake-up| Blink (1s)| | |
GPS| GPS Connection| | | ON| X
GPS not Connection| | | OFF| X
Network| Network Connection| | ON| | X
Network not Connection| | OFF| | X
Data Transmitting (LTE)| | Blink
(0.1s)| X|
eSIM Error| Blink (0.5s)| Blink (0.5s)| | Beep (0.1sX1)
Dangerous
Driving| Sudden Acceleration/Deceleration| | | | Beep (0.5sX2)
Impact| | | | Beep (0.5sX1)
Hibernate| OFF| OFF| OFF| X
Extension cable Components
Devices
Manual
Available separately
Installation
- Please turn on the engine before installation
- Locate the OBD port (Usually located on the left of the steering wheel and underneath your dashboard)
- If you are having difficulty covering the fuse box after installation, please detach the OBD port and push it toward the fuse box
- If an installation is a complete LED light will be turned on
- Start your engine after fixing the device
Warranty
- Device Info
- Model: JLM1-2000
- FCC Certification : 2ASMR-JLM1-2000
-
Warranty Period
1 year after purchase -
Coverage
- Immediately and effectively notify Guarantor about determined device’s defects and cease any using it.
- The Warranty does not cover: Damages due to the user’s fault or lack of knowledge
- Return and change
- Returns are only accepted within a week. It must also be in the original packaging.
- For the change of mind return, the shipping fee will be charged
- Miscellaneous
- For those who cannot confirm the purchase date, the warranty start date will correspond to the activation date.
- Repair fee will be charged for the following cases
– Damage due to the user’s fault or lack of knowledge
– The device that has been tempered with reconfiguration, repair, willful constructional variations, modifications, and adjustments
– Damages caused by acts of God, floods, fires, lighting or other natural disasters, wars, unexpected events, inappropriate voltage, defective supply materials or other external factors;
– Defects resulting from the usage of improper or non-genuine supply materials;
- Contact
82-1599-8439
Warning Statement
FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Part 15.105 statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication ns.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged ed to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
RF Exposure Statement
This equipment should be installed and operated with a minimum of 20 cm
between the radiator and your body.
This transmitter must not be collocated or operating in conjunction with any
other antenna or transmitter unless authorized to do so by the FCC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>