Nwe Brands PSBTS95LT Wireless Pixel Party Dancing Lights Speaker User Manual
- June 6, 2024
- Nwe Brands
Table of Contents
Nwe Brands PSBTS95LT Wireless Pixel Party Dancing Lights Speaker
Specifications
- Model Number ：PS-BTS95LT
- Product Weight ：487g
- Product Size ：13013063MM
- Material： ABS
- Horn Size（Speaker driver） ：52MM
- Microphone size ：4013
- Product channel: Wireless Pixel Party
- Dancing Lights Speaker
- BT Version： V5.0+BR+EDR+BLE
- BT Protocol ：A2DP 1.0 AVRCP 1.5 AVDTP 1.0 AVCTP 1.4 HFP 1.5 GAVDP 1.0
- Working Distance（BT range）： 10-15M
- Input voltage： DC5V
- Input current: 1A
- Charging time: ≥4H
- Output power: 5W
- Working Time（Middle Sound with the led light）： 4-6H
- Standby time:： 25H
- Battery type :18650
- Battery voltage: 3.7-4.2V
- Battery capacity： 2400mAH( 2 pcs 1200mAh )
- Frequency response: 30-18KHZ
- Speaker impedance :4Ω
- Sensitivity: 500MV
- SNR (Signal to Noise Ratio): 74dB
- Distortion: ≤3%
- Audio format: WAV/MP3
- Support Function ： BT、 USB、TF、TWS
- Maximum supported memory card capacity: 32GB
- FM frequency range:： 88-108MHZ (optional function)
Function Description:
-
short press to play / Pause、Press and hold for 3 seconds to check the battery capacity, and press and hold 5S to turn on or off the colored lights. Double-click to enter TWS mode; When you call, press once to answer, then press again to hang up.
-
Short press to volume down, long press to change into last song
-
Short press to volume up, long press to change into next song
-
Power button, long press: switch on and off, short press: color light mode switch; double click: switch mode.
-
MICRO 5P charging port
-
LED indication: blue light flashes slowly when playing music, flashes quickly when Bluetooth and radio search working, the red light is turn on when charging, and the green light is turn on when it is full
Built-in MIC entrance -
USB card port, support MAX 32G flash,Compatible with WAV/MP3 files
-
TF card port, support MAX 32G flash,Compatible with WAV/MP3 in high fidelity
TWS instructions: When both speaker are in the Bluetooth search state,，double – click the power buttons to enter the TWS mode. After hearing the tone, the two machines start to pair. After the connection is successful, the secondary unit blue light is always on, and the host continues to search until the connection is completed
FM instruction: Insert the LINE in cable to use as the FM external antenna. double-click the power button to enter the FM function, then press the play button to start searching. The search process blue light flashes quickly, and the channel is automatically saved after the search is completed. Press and hold the volume plus or minus button to switch the audio channe
Tips： There is a warning sound when playing, it is power low, please charge the speaker (Charging voltage: 5V, charging currency ≥ 1A )
This device complies with part 15 of the FCC Rules. Operation is subject to
the condition that this device does not cause harmful interference (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
FCC ID: 2AZPE-PSBTS95LT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>