metabo SSD 18 LT 200 BL Brushless Impact Driver Instructions
- June 6, 2024
- metabo
Table of Contents
PROFESSIONAL POWER TOOL SOLUTIONS
SSD 18 LT 200 BL
SSW 18 LT 300 BL
| SSD 18 LT 200 BL
1) Serial Number: 02397…| SSW 18 LT 300 BL
1) Serial Number: 02398…
---|---|---
U| V| 18| 18
no| /min, rpm| 0 – 3050| 0 – 3050
S| /min, bpm| 3750| 3900
H| –| 1/4″ (6,35 mm)| 1/2″ (12,70 mm)
m| kg (Ibs)| 1,6 (3.5)| 1,6 (3.5)
M1| Nm (in-Ibs)| 40 (354)| 50 (443)
M2| Nm (in-Ibs)| 150 (1328)| 175 (1549)
M3| Nm (in-Ibs)| 200 (1770)| 300 (2655)
ah / Kh| M/S 2| 14,0 / 1,5| 13,8 / 1,5
LpA / KpA| dB(A)| 97 / 3| 97 / 3
LwA / Km| dB(A)| 108 / 3| 108 / 3
2) 2014/30/EU, 2006/42/EC, 2011/65/EU
3) EN 62841-1:2015, EN 62841-2-2:2014, EN IEC 63000:2018
2021-04-21, Bernd Fleischmann
Direktor Produktentstehung & Qualität (Vice President Product Engineering &
Quality)
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany
Original instructions
Declaration of Conformity
We hereby declare under our sole responsibility that these cordless impact
drivers, identified by type and serial number 1), meet all relevant
requirements of directives 2) and standards 3).
Technical documents for 4) – see page 3.
For UK only:
We as manufacturer and an authorized person to compile the technical file, see
4) on page 3, hereby declare under sole responsibility that these cordless
impact wrench, identified by type and serial number 1) on page 3, fulfill all
relevant provisions of the following UK Regulations S.I. 2016/
1091, S.I. 2008/1597, S.I. 2012/3032 and designated Standards EN 62841-1:2015,
EN 62841-2-2:2014, EN IEC 63000:2018.
Specified Conditions of Use
The impact driver is suitable for driving in and removing screws.
The user bears sole responsibility for any damage caused by inappropriate use.
Generally accepted accident prevention regulations and the enclosed safety
information must be observed.
General Safety Information
** For your own protection and for the protection of your power tool, pay
attention to all parts of the text that are marked with this symbol!
WARNING – Read the operating instructions to reduce the risk of injury.
WARNING** – Read all safety warnings, instructions, illustrations, and
specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury.
Keep all safety instructions and information for future reference.
Always include these documents when passing on your power tool.
Special safety instructions
Hold the power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring.
Fasteners contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
Remove the battery pack from the machine before making any adjustments,
changing tools, maintaining, or cleaning.
Make sure that the tool is switched off before fitting the battery pack.
Ensure that the spot where you wish to work is free of power cables, gas
lines, or water pipes (e.g. using a metal detector).
Secure the workpiece to prevent slipping or rotation(e.g. by securing with
screw clamps).
Protect battery packs from water and moisture!
Do not expose battery packs to fire!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short circuit battery pack contacts!
A slightly acidic, flammable fluid may leak from defective Li-Ion battery
packs!
If battery fluid leaks out and comes into contact with your skin, rinse
immediately with plenty of water. If battery fluid leaks out and comes into
contact with your eyes, wash them with clean water and seek medical attention
immediately!
If the machine is defective, remove the battery pack from the machine.
Only screwdriving bits suitable for the impact drivers must be used.
Take care when driving in long screws – the risk of slipping.
Mount the machine on the screw only when it is switched off.
Wear ear protectors when working for long periods of time. High noise levels
over a prolonged period of time may affect your hearing.
LED light (7): do not observe the LED radiation directly with optical
instruments.
Transport of Li-Ion battery packs:
The shipping of Li-Ion battery packs is subject to laws related to the
carriage of hazardous goods (UN3480 and UN 3481). Inform yourself of the
currently
valid specifications when shipping Li-Ion battery packs. If necessary, consult
your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact and no fluid is leaking.
Remove the battery pack from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with adhesive tape).
Reducing dust exposure:
WARNING – Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known to cause cancer,
birth defects, or other reproductive harm. Some examples of these chemicals
are:
– Lead from lead-based paints,
– crystalline silica from bricks and cement and other masonry products, and
– arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well-ventilated
area, and work
with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
This also applies to dust from other materials, such as some timber types
(like oak or beech dust), metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let dust enter the body.
Observe the relevant guidelines and national regulations for your material,
staff, application, and place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid deposits in the
surrounding area.
Use suitable accessories for special work. In this way, fewer particles enter
the environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
– do not direct the escaping particles and the exhaust air stream towards
yourself or nearby persons or towards dust deposits,
– use an extraction unit and/or an air purifier,
– ensure good ventilation of the workplace and keep it clean using a vacuum
cleaner. Sweeping or blowing stirs up dust.
– Vacuum or wash protective clothing. Do not blow, beat or brush protective
gear.
Overview
See page 2.
-
Square attachment for 1/2“ tools *
-
Hexagon socket attachment for hexagon screwdriving bits*
-
Locking sleeve*
-
Rotation selector switch / Transporting safety device
-
Trigger
-
Handle (gripping surface)
-
LED light
For working in badly lit areas. The LED light lights up when the machine is switched on. -
Button for speed and tightening torque selection
-
Battery pack *
-
Battery pack release button
-
Capacity indicator button *
-
Capacity and signal indicator *
-
Belt hook (attach as shown) *
- depending on the features/model
Initial Operation/Setting
Remove the battery pack from the machine before any adjustment or maintenance is carried out. Make sure that the tool is switched off before fitting the battery pack.
6.1 Battery pack
Charge the battery pack (9) before use. Recharge the battery pack if
performance diminishes.
Instructions on charging the battery pack can be found in the operating
instructions of the Metabo charger.
Li-Ion battery packs “Li-Power, LiHD“ have a capacity and signal indicator
(12):
– Press the button (11), the LEDs indicate the charge level.
– The battery pack is almost empty and must be recharged if one LED is
flashing.
Removing:
Press the battery pack release button (10) and pull the battery pack (9)
forwards.
Inserting:
Slide in the battery pack (9) until it engages.
6.2 Setting the direction of rotation, engaging the transporting safety device (switch-on lock)
Only operate the rotary selector switch / transporting safety device (4) when
the motor is at standstill!
Actuate the rotation selector switch / Engage the transportation lock (4).
R = Clockwise setting (drive-in screws)
L = Anti-clockwise setting (undo screws)
0 = middle position: transportation safety device (Switch-on lock) set
6.3 Switching on and off Switching on: press the trigger switch (5).
Switching off: Release the trigger (5).
6.4 Speed/tightening torque
The speed and tightening torque are connected directly. The lower the speed,
the lower the tightening torque.
The tightening torque is influenced in two ways:
-
Select maximum tightening torque.
You can select one of three tightening torque settings by pressing the button (8). The maximum tightening torques can be found in the table on page 3 (M1, M2, M3).
The lights indicate which setting is selected.
1 = min. tightening torque
2 = medium tightening torque
3 = max. tightening torque -
Stepless adjustment of the tightening torque:
The speed and tightening torque can be adjusted steplessly in any torque setting by pressing the trigger (5) firmly or lightly, thus adapting to working conditions.
Recommendation: determine the correct setting by carrying out trial screwdriving.
6.5 Changing SSD screwdriving bits Inserting screwdriving bit: Slide locking sleeve
(3) forward and insert screwdriving bit as far as the stop. Release locking
sleeve (3).
Pull-on the screwdriver bit to check that it is correctly seated.
Removing screwdriving bit: Slide locking sleeve
(3) forward and remove the screwdriving bit.
Only use screwdriving bits with such plug-in ends:
The screwdriving bit used must match the screw.
Damaged screwdriving bits must not be used.
6.6 Change screwdriving bit for SSW …
Inserting screwdriving bit: Fit the tool on the square attachment (1)
until the limit stop.
Removing screwdriving bit: Pull the tool from the square attachment (1).
The screwdriving bit used must match the screw.
Damaged screwdriving bits must not be used.
Use
Mount the machine on the screw, ensuring it is aligned straight.
The screwdriving process consists of 2 parts: insertscrew and tighten the
screw with the impact mechanism.
The tightening torque depends on the impact duration.
With an impact duration of approx. 5 seconds, the maximum tightening torque
has been reached.
The torque curve depends on the type of application:
With a hard screwdriving application (screw-couplings in a hard material such
as metal), maximum tightening torque is already reached after a short impact
duration (a).
With a soft screwdriving application (screwcouplings in a soft material such
as wood), a longer impact duration (b) is required.
Recommendation: determine the correct impact duration by carrying out trial
screwdriving.
Caution! For small screws, the maximum torque can be reached already
after 0.5 seconds impact duration.
– This is why the duration of the screwdriving process must be monitored
exactly.
– Set an (8) suitable tightening torque using the button (see chapter 6.4).
– Adjust the tightening torque by pressing firmly or lightly on the trigger
(5), ensuring that the screw is not damaged or that the screw head does not
tear off.
Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfill the requirements and specifications listed
in these operating instructions.
See page 4.
A Chargers
B Battery packs with different capacities
Use only battery packs with a voltage suitable for your power tool.
C Screwdriving bits
For a complete range of accessories, see
www.metabo.com or the catalog.
Repairs
Repairs to electrical tools must ONLY be carried out by qualified
electricians!
Contact your local Metabo representative if you have Metabo power tools
requiring repairs. For addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Environmental Protection
Observe national regulations on environmentally compatible disposal and on the
recycling of disused machines, packaging, and accessories.
Battery packs may not be disposed of with regular waste. Return faulty or used
battery packs to your Metabo dealer!
Do not allow battery packs to come into contact with water!
Only for EU countries: never dispose of power tools in your household waste!
According to European Directive 2012/19/EU on Waste from Electric and
Electronic Equipment and implementation in national law, used power tools must
be collected separately and recycled in an environmentally-friendly manner.
Discharge the battery pack in the power tool before disposal. Prevent the
contacts from short-circuiting (e.g. by protecting them with adhesive tape).
Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
n0 = No-load speed
S =impact frequency
H = machine tool holder
m = weight (with the smallest battery pack)
M1 = min. tightening torque
M2 = medium tightening torque
M3 = max. tightening torque
Measured values determined in conformity with EN 62841.
Permitted ambient temperature during operation:
-20 °C to 50 °C (limited performance with temperatures below 0 °C). Permitted ambient temperature for storage: 0 °C to 30 °C direct current
The technical specifications quoted are subject to tolerances (in compliance
with relevant valid standards).
Emission values
These values make it possible to assess the emissions from the power tool and
to compare different power tools. The actual load may be higher or lower
depending on operating conditions, the condition of the power tool, or the
accessories used.
Please allow for breaks and periods when the load is lower for assessment
purposes. Arrange protective measures for the user, such as organizational
measures based on the adjusted estimates.
Vibration total value (vector sum of three directions) determined in
accordance with EN 62841:
ah = Vibration emission value (screwdriving with impact)
Kh = uncertainty (vibration)
Typical A-weighted sound levels:
LpA= sound-pressure level
LWA= acoustic power level
KpA, KWA = Uncertainty (noise level)
Wear ear protectors!
Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>