Gaggenau 9001923390_A Free Standing Dishwasher Instruction Manual

: June 6, 2024
: Gaggenau

Table of Contents

Gaggenau 9001923390_A Free Standing Dishwasher
IMPORTANT SAFETY INSTRUCTIONS
Before you begin
Installation Procedure
Dishwasher Connection
Customer Service
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Gaggenau 9001923390_A Free Standing Dishwasher

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Read all of the instructions carefully before using the appliance. To reduce the risk of fire, electric shocks and personal injuries when using the appliance, follow the basic safety precautions, including the following safety instructions.

Safety definitions
Here you can find explanations of the safety signal words used in this manual.

WARNING: This indicates that death or serious injuries may occur as a result of non-observance of this warning.
CAUTION: This indicates that minor or moderate injuries may occur as a result of non-observance of this warning.
NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.
Note: This alerts you to important information and/or tips.

General information
To reduce the risk of fire, electrical shock, or serious injury, observe the following.

This appliance is provided with installation instructions and this use and care manual. Read and understand all instructions before using the appliance.
Keep the manual and the product information in a safe place for future reference or the next owner.
Do not connect the appliance if it has been damaged in transit.
Product damage and/or injury could result from the use of unqualified service technicians or non-original parts. All repairs should be performed by an authorized service provider using only original equipment factory replacement parts.
NSF/ANSI 184 Certified residential dishwashers are not intended for licensed food establishments.

Safe Installation
Follow these safety instructions when installing the appliance.

These instructions are intended for use by qualified installers only. The dishwasher must be installed by a qualified technician or installer.
The dishwasher drain hose must be installed with a portion of it at least 33″ (84 cm) off the floor; otherwise, the dishwasher may not drain properly.
This dishwasher is not for outdoor use. It is intended for indoor residential use only, and should not be used in commercial food service establishments.
This dishwasher is designed to be enclosed on the top and both sides by cabinetry.
NEW INSTALLATION – If the dishwasher is a new installation, ensure all connections are properly made before the dishwasher is moved into place.
REPLACEMENT – If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary.
This appliance complies with CAN/CSA-C22.2 No. 167/UL 749. It is the responsibility of the owner and the installer to determine if additional requirements and standards apply in specific installations.

WARNING: Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. Hydrogen gas is explosive.

Before using a dishwasher that is connected to a hot water system that has been unused for two weeks or longer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is explosive, do not smoke or use an open flame during this time.

Electrical safety
Follow these safety instructions to avoid electrical shock. ¡ The dishwasher must be properly grounded before operating. This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dishwasher.

DO NOT use an extension cord
DO NOT reuse an old power cord; only use the cord provided.
Make sure that the dishwasher is connected to a suitable ground in compliance with all local codes or, in the absence of a local code, with the NATIONAL ELECTRICAL CODE in the United States or the CANADIAN ELECTRIC CODE C22.1-latest edition in Canada as well as any provincial/state or municipal or local codes that apply
Installations requiring hard wiring and terminal block The accessory terminal block/junction box model, SMZPCJB1UC, designed for permanent wire connection, is not included but can be ordered through Customer Service by calling 1-800-944-2904. Follow the instructions included in the kit.

WARNING
Avoid Electrical Shock

Do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized.
To avoid possible injury or property damage, care should be exercised when the dishwasher is installed or removed to reduce the likelihood of damage to the power cord.

WARNING Avoid Fire Hazard

Make sure electrical work is properly installed and checked by qualified electricians.
Make sure there are no loose electrical connections. Make sure all electrical connections are properly made. Loose and improperly installed electrical connections can result in overheating!

Wall outlet connections

Only use the provided power cord for wall socket connections.
DO NOT attach an extension cord or any type of modified cord or adapter to this appliance.
DO NOT cut or splice the power cord.
DO NOT alter the power cord in any way.

Permanent wire connections (in addition to the warnings above)

Only use the junction box power cord, sold as Accessory kit #SMZPCJB1UC.
Carefully review the terminal block installation instructions.
DO NOT remove, alter or bypass the terminal block.

State of California Proposition 65 Warnings
This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:

STATE OF CALIFORNIA PROPOSITION 65 WARNING:

WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Before you begin

Before you begin
Before you begin
Read these instructions before you begin to install your appliance.

Inspect the Dishwasher
After unpacking the dishwasher and before installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately. Cosmetic defects must be reported within 30 days of installation. NOTE: Do not discard any bags or items that come with the original package until after the entire installation has been completed.

Parts Included
After unpacking all the parts, check for any damage in transit or missing parts.

Tools and Parts Needed
Gather these tools and additional parts before beginning the installation of your appliance.

Tools

Pre-install Checklist
Ensure that the following requirements are met when planning the installation of your appliance.

WARNING: Avoid Scalding or Electric Shock Hazard

Make sure the water supply and electrical supply are shut off before installation or service.
Do not allow the electrical and supply lines to touch. ¡ Select a location as close to the sink as possible for easy access to water supply and drain lines.
Be sure the unit is installed close enough to the sink so the drain hose length does not exceed 92″ (2337 mm) and so that a portion of the drain hose is raised at least 33″ above the floor level.
Ensure that the enclosure is square and the opening is at least 34 1/8″ (867 mm) high and 23 5/8″ (600 mm) wide.
Check that the opening in the cabinet is large enough for routing the electric cable, water line, and drain hose, and if not, create a new opening. See “Installation Preparation”,
If the opening is wood, be sure it is sanded smooth. If it is metal, be sure it is covered by a protective gasket.
Be sure that your water heater is set at 120° F (49° C) and the water pressure measures at 15-145 psi (1-10 bar)
Determine the mounting method based on the → “Mounting Brackets”, Page 8 .
Only use the included hardware for the installation. If you are replacing a dishwasher, dispose of old hose and other equipment properly.
To avoid scratching the floor, have floor protection ready for when the dishwasher will be slid into the cabinet

Electrical Requirements
Ensure that the following electrical requirements are met.

Dishwasher electrical rating

Volts 1 20
Hertz 60
Ampere s 12
Watts 1,440 (max)

Electrical Supply
The customer has the responsibility of ensuring that the dishwasher electrical installation complies with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated 15 or 20 amps.

Cabinet Requirements
Ensure that the cabinet space for the installation meets the required dimensions.

If the dishwasher is to be installed in a corner, ensure that there is adequate clearance to open the door as shown.

Installation Preparation
After locating the proper place for your dishwasher, create an opening to allow for water, drain and electrical lines on the appropriate side.

Cut a rectangular hole 2.5″ x 3.5″ in the rear corner on the sink-facing side. If the opening is made through wood, sand it smooth. If the opening is made through metal, use the Edge Protector with Power Cord clips Kit SMZEPCC1UC.
Remove the rubber apron from the top of the dishwasher.1
Remove the hose clip from the back of the dishwasher.
It can be used later to hold the drain hose inside your cabinet.

Installation Procedure

Installation ProcedureFollow these instructions to install the dishwasher.

Pre-level the Dishwasher
Set the dishwasher to the correct height before it goes into the cabinet.

Measure the height of the cabinet opening.
Raise the front of the dishwasher to approximately 1/2″ lower than the height of the opening by turning the feet clockwise. You can raise the rear foot after the unit is in the cabinet opening.
Use a level on the top front to see that both feet are even.

Attach Power Cord

Plug the end of the supply cord into the back of the dishwasher.
- Be sure to push it in until fully seated.
  The outlet for the power supply cord should be located in a cabinet or wall adjacent to the dishwasher cabinet. Do not plug dishwasher into the wall outlet until all the steps of the installation are complete.
Notes
- If you require a permanent wiring connection, order kit junction box accessory kit SMZPCJB1UC.
- If local electrical codes require clips to secure the power cord wire to the dishwasher, use accessory kit SMZEPCC1UC.

Mounting Brackets
Before installing the supplied mounting brackets, decide which method of securing the dishwasher into its enclosure will be used, top (wood or porous material) or side (stone or solid surface). Once the mounting brackets are installed on the dishwasher, removing them is difficult and will damage the mounting brackets and the dishwasher. If you have a Fully Integrated Panel, do not attach mounting brackets until after attaching the panel to the door.

WARNING: Avoid tip-over hazard

Do not use the dishwasher until it is completely installed. When opening the door on an uninstalled dishwasher, carefully open the door while supporting the rear of the unit. Failure to follow this warning can result in serious injury.

Top and Side Mount
For openings wider than 23 5/8″ (600 mm), use the metal mounting brackets. The top mount is for wood or other materials that can easily be drilled into. The side mount is for stone countertops or another hard material that cannot easily be drilled. Both use the same mounting brackets, but the difference is the screw placement.

Orient the mounting brackets as shown and position the tabs into openings on the dishwasher’s front corners.
- For side mount, bend the brackets down at the perforation.

Side Mount Force Distributor
The side mount force distributors are for cabinet openings that are 23 5/8″.

Insert a side mount force distributor into the opening in each side. Make sure it is flush with the dishwasher.

Attaching the Apron1

Remove the tape covering the adhesive strip on the rubber apron.
Adhere the apron to the front of the dishwasher.

Install Dishwasher in Cabinet Space
To avoid scratching the floor, use floor protection and caution when sliding the dishwasher into the cabinet.

NOTICE: Avoid Hose Kinks

Be careful while pushing the dishwasher in. The hoses can fold, kink or break, potentially causing an obstruction or leak.

Feed the power cord and hoses through the low hole in the cabinet.
Carefully and slowly push the dishwasher into the cabinet space.
Reach into the adjacent cabinet and pull hoses and excess power cords through completely so they do not get kinked.
Finally, push the unit in until flush with cabinet door.
Center the dishwasher in the opening.

Level the Dishwasher
Now that the dishwasher is in the cabinet, check the levels again.

Level side to side by turning feet clockwise to raise or counter-clockwise to lower front.
Level front to back by turning centre screw clockwise to raise or counter-clockwise to lower the back.
Use a level to check that your dishwasher is level.
- Ensure that the countertop is level and adjust the dishwasher to the countertop.
Make sure the top of the door is no less than 1/4″ (6\ mm) from the underside of the counter.

Outer Door Assembly1

Follow the instructions for outer door assembly on the fully integrated template.

Secure Top and Side Mount

For top mount, drive the mounting screws through the holes in the bracket into the countertop.
For side mount, drive the mounting screws through the holes in the sides of the cabinetry.
If using the force distributor side mounts, first remove the cutlery rack.1
Drive the mounting screws through the holes inside the dishwasher.
Re-insert the cutlery rack.

Attach the 2-part Toe Panel

If your dishwasher has a rubber apron, install the 2-part toe panel behind the apron.
Place the slotted toe panel on the dishwasher.
- It should rest on the floor.
Position the mating front toe panel on top of the rear toe panel with the angled edge on the mating edge of the dishwasher.
To secure the toe panels, drive the two black torx screws through the holes in the toe panel and the dishwasher base.
- To avoid damaging the dishwasher, use the supplied screws.

Attach the Outer Toe Panel
NOTICE: Avoid door interference

To ensure the door can open and close without any interference, check the clearance when installing the outer toe panel.

Slide the supplied brackets into the slots of the toe panel you just attached.
To ensure that the outer toe panel is flush with the cabinetry base, determine the correct position for the brackets.
Mark the correct position, then slide the brackets out and bend out the metal tab at the correct position.
Bending a tab ensures that the toe panel cannot slide in further.
Re-insert the brackets.
Secure the outer toe panel with the crosshead screws provided.
- The outer toe panel should completely cover the rubber apron.
To cover the screw heads, use the black plastic caps.

Dishwasher Connection

Dishwasher Connection
Follow these instructions to connect the dishwasher.

Installing the Water Inlet Connection
The water heater should be set to deliver approximately 120 °F (49 °C) [max. 140 °F/ (60 °C)] water to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 7.25 – 145 psi (0.5 – 10 bar).

WARNING Scalding Hazard

Do not perform any work on a pressured hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off.

NOTICE: Soldering plumbing lines
Temperatures required for soldering and sweating will damage the dishwasher. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher.

Plumbing codes
Check local plumbing codes for approved plumbing procedures and accessories. All plumbing should be done under national and local codes.

Note
Important notes for water connection:

If using a solder joint instead of a compression fitting, be sure to complete all solder connections before connecting the water supply line to the dishwasher.
Use an approved dishwasher water supply line with the correct fittings for this connection.
If using copper tubing or other material not depicted in this manual for water supply, defer to a licensed plumber for proper installation.

Always use appropriate seals when making plumbing connections.

Flush the incoming water line for approximately 1 minute to clear any foreign material.
Connect the dishwasher water supply line to the water shut-off valve, using the adaptor if included with your model.
- Install a shut-off valve if one isn’t already in the supply line.
- Make sure there are no sharp bends or kinks in the water line that might restrict water flow.
Properly tighten all water connections.
After all connections are made, turn on the hot water and check for leaks.

Installing the Drain Connection
The drain hose must be installed with either a high loop or an air gap.

NOTICE: Proper drain hose installation

The dishwasher drain hose must be installed with a portion of it at least 33” (84 cm) off the floor; otherwise, the dishwasher may not drain properly.
Remove the garbage disposal plug
If the dishwasher drain hose will be connected to a garbage disposal connection, first remove the plug from the disposal connection.

Note
Important notes for drain connection:

If local ordinances require an air gap, install it according to the manufacturer’s instructions.
The drain hose length can be extended if necessary.
Use kit #SGZ1010UC. The maximum length of the drain hose, including the hose leading to the air gap, is 150″(380 cm).
You may attach the hose clip to the inside of the adjacent cabinet to hang the drain hose (screws are not supplied) in place of using a nonmetallic tie as pictured in the next illustrations. Do not exceed 43” in drain hose height.
1. Place hose clamp around the end of the drain hose BEFORE connecting to the plumbing.
2. If you have a garbage disposal, connect the drain hose to the garbage disposal with either a high loop or an air gap.
3. If you do not have a garbage disposal, connect the drain hose to the drain connection with either a high loop or an air gap.
4. Insert the included drain hose adaptor before connecting to the plumbing.
5. Tighten the hose clamp around the house plumbing.

Electrical Connection and Test Cycle

For wall outlet connections, plug the dishwasher into the outlet.
Turn on power supply.
Make sure the water supply is on.
Turn the dishwasher on and run a test cycle for 15 minutes.
Check to make sure the cycle operates and there are no leaks while it is running.
Stop the cycle and turn off the dishwasher.
Your installation is complete.

Customer Service

With any warranty repair, we will make sure your appliance is repaired by an authorized service provider using genuine replacement parts. We use only genuine replacement parts for all repairs.
Detailed information on the warranty period and terms of the warranty can be found in the Statement of Limited Product Warranty, from your retailer, or on our website.
If you contact Customer Service, you will need the model number (E-Nr.) and the production number (FD) of your appliance.

USA:

CA:

Model number (E-Nr.) and production number (FD)

You can find the model number (E-Nr.) and the production number (FD) on the appliance’s rating plate.
The rating plate is located inside the appliance door.
Making a note of your appliance’s details and the Customer Service telephone number will enable you to find them again quickly.

BSH Home Appliances Corporation
1901 Main Street, Suite 600 Irvine, CA 92614

USA