SECURVIEW MDVR-J400 4G/WiFi In-Vehicle Surveillance and GPS Tracking System User Guide
- June 6, 2024
- SECURVIEW
Table of Contents
MDVR-J400 4G/WiFi In-Vehicle Surveillance
and GPS Tracking System
User Guide
Thank you for purchasing a Securview Vehicle Surveillance & Tracking System
This Quick Start Guide covers the basic setup, installation, and use of your
surveillance system.
For more information, please visit:
www.securviewcctv.com
Included Components
Overview & Installation
System Diagram
Note: The SIM card and Micro SD card sockets are push-in-push-out type. Do not use any tools to extract cards.
Golden contacts face up Warranty void if cards are inserted the wrong way
Technical Specifications
| Camera | Model | MDVR-J400 |
|---|---|---|
| Camera Style | Windscreen-mounted road camera, Dash-mounted driver camera | |
| Resolution | Road: 1080p (1920 x 1080) / Driver: 720p (1280 x 720) | |
| Angle of View | Front: 120° (adjustable) / Rear: 100° | |
| Focus | Fixed | |
| Frame Rate | 30fps (Dynamic) | |
| Features | CPU | ARM Cortex A53 1.4GHZ |
| Band | GSM 850/900/1800/1900 / WCDMA B1/B2/B5/B8 / |
FDD B1/B3/B5/B7/B8/B20 / TDD B38/B39/B40/B41 (100M)
G-Sensor| 9 axis-motion
Live View| In-car / front car live video via app or web
Audio| Built-in microphone / Built-in speaker
WiFi| 802.11 b/g/n, 2.4GHz frequency, hot spot
Bluetooth| N/A
Micro SD storage| Max 128GB
Battery| External 450mAh
Interface| OBD Interface| Connect by power cable
USB Data Interface| Micro USB 5 Pin (For engineering purposes only, not for
data backup)
Housing| Plastic
Power Input| 9 ~ 36VDC
Dimensions| 109 x 69 x 52mm
Weight| 0.23kg
Operating Environment| -20°C to 75°C / RH95% (max)
Installation
Wiring
Connect cables according to 1.3.2 Wiring Diagram. Connect the power cable B+
(Red wire) and GND (Blackwire) to the vehicle battery’s +12V/+24V terminal and
negative terminal respectively. Connect ACC (Yellow wire) to the vehicle ON
position.The device should power on automatically after the vehicle engine is
started.
Remember to connect the battery backup module.
Wiring Diagram
Micro SD and SIM Card
While the system if off, insert a Micro SD card into T.FLASH slot and an
active SIM card into the SIM slot (both located on one side of the camera).
After inserting both cards, screw on the card cover with the provided screw &
screwdriver.
Status Indicator Lights
Power Indicator
(RED)| | Solid red| ACC ON & Power on
---|---|---|---
| 0.1s ON & 10s OFF| ACC OFF
| Off| Power not connected
GPS Indicator
(GREEN)| | Solid green| ACC ON & Positioning succesful
| 0.1s ON & 1s OFF| Searching for GPS signal
| Off| ACC OFF
3G Indicator
(BLUE)| | Solid blue| ACC ON & Connected
| 0.1s ON & 1s OFF| ACC ON & No network/SIM card
| Off| ACC OFF
SIM Card
Ensure you are using an active Micro SIM card (or Nano SIM with adapter).
Standard SIM cards will not work.
- 4G SIM card required (4G+3G). 3G SIM cards will not work (3G+2G).
- Must have data, voice and SMS capabilities.
- Must be able to monitor data usage, check balance and automatically/manually top up remotely.
Car Status Update
All driving data and car status are uploaded to the webserver, there is some
delay between the car status on the webserver and the real situation. For
example, when the car switches its engine ON/OFF, it’s on/off status will be
updated on the webserver and indicate one the APP after 10 seconds or more.
For the Device List menu which shows all registered devices, you need to
update the status manually by “pull-to-refresh”.
Operation
Automatic & Event Recording
Automatic Recording
ACC ON – The system will power on and record automatically.
ACC OFF – The system is in sleep mode and will not record.
Recordings will be saved onto the micro SD card every 3 minutes, under the
directories:
DVRMEDIA/CarRecorder/GENERAL/ForwardCam (road camera)
DVRMEDIA/CarRecorder/USB/InwardCam (driver camera)
NOTE: When the Micro SD card is full, old footage on the card will be overwritten.
Event Recording
If a strong vibration is detected (from a crash, for example), an additional
15s will be recorded and then stored in a separate location under
DVRMEDIA/CarRecorder/EVENT
The EVENT folder stores 1GB of footage. Old recordings in EVENT will be
overwritten when the folder is full.
System Usage
SIM Card Usage
This system is intended for use with a SIM card, but can still function as a
mobile video recorder without one. Refer below to see what the system can do
with and without a SIM card:
SIM Required
• Remote Live View
• Remote GPS Tracking
• Remote Picture/Video Capture
• Push Notifications (Geo-fence, vibration alert, etc.)| SIM Not Required
• Automatic Recording
• GPS History Logging
• Event History
• Media Synchronisation
---|---
App & Web Usage
The system can be accessed, monitored, and configured via a mobile app and web
browser. Visit: www.tracksolid.com. for the web
version.
Configuration
App Introduction
Your vehicle monitoring system can be accessed, monitored, and configured
via a mobile app.
Switch between cameras on your account on the phone.
App Intro
The vehicle tracking app is Tracksolid, available to download free from iPhone
App Store & Google Play Store.
This app allows for portable vehicle management, letting you perform a variety
of functions such as:
- Real-time GPS vehicle tracking & location reporting
- Real-time push notifications for Overspeed, vibration, geo-fence, etc.
- Geo-fencing – alerts account when the vehicle enters or leaves a designated zone
- Route playback for vehicle history
- Remote live view, playback, image snapshot & video snapshot
- Media synchronization for easy file transfers from the recorder
Account Registration
Account Creation
- Press Sign Up on the front page of the app.
- Enter your email address and tap Next to send a verification code to your email address.
- Enter the verification code into the app and tap Next again to finish creating your account.
Change Password
- (App) Open the Home screen and tap the user icon next to your email address.
- Tap Change Password.
- Enter the current password, then enter your new password twice and tap Save.
Note: After account registration, you will be automatically prompted to bind a device.
Binding Your Device to an Account
Adding Your Device
- Tap the ‘+’ icon on the Home screen.
- Enter the 15-digit IMEI then tap Add Device to continue or scan the QR code of your device which is printed on the top cover of the camera.
- Enter the device name, number plate of the vehicle, driver name, contact number, and select a device icon. Tap Save to finish.
Unbinding Your Device
- Open the Home screen and tap List to enter the Device List menu.
- Tap the icon on the device to be unbound.
- Tap Unbound to continue.
- Tap OK to confirm.
Note: MDVR-J400 cameras can only be bound to one mobile phone at a time. If you want to register the device on another mobile phone, you must unbind the device on the original mobile phone first.
Device Settings
- Open the Home screen and tap List.
- Tap the icon on the device to edit, then tap Settings.
- You can edit Alert Settings, Overspeed Alert, Driving Behaviour, Vibration Alert, Crash, LED, Voice, SOS, and Geofence Video settings of your device.
Note: DMS (Driver Monitoring System) is only for AI models, and is not
applicable for MDVR-400.
Vibration Alarm
- When ACC is ON, the Vibration alarm is disabled.
- When ACC is OFF, the Vibration alarm will switch on automatically after 5 minutes. If vibration is detected, the device will report alarm conditions in 5 seconds. If ACC is ON within this 10 second period, the alarm reporting and vibration alarm will be canceled otherwise it will alarm for 30 seconds.
- After the alarm period, the device stops detecting variation alarms for 1 minute. After 1 minute, it will resume the vibration
alarm. The sensitivity of the vibration sensor is adjustable on the App as described above.
Emergency Functions
SOS
- The SOS button allows you to send a defined SOS message to the APP user and call up to 3 SOS numbers.
- SOS button will activate only if the button is pressed and held down for more than 3 seconds.
- Note: SOS alert must be enabled in the Alert Setting menu.
-
Select the device to set in the List menu then and tap Command.
-
Tap SOS number:
• Select SOS setting to enter numbers
• Select Delete SOS number setting to delete numbers
• Select Query SOS number to check SOS numbers already set -
Tap Send to confirm.
-
Starter Cut
To cut the start cut:
- Tap Fuel/Power Remote Control.
- Select Cut off
- Enter the App password then tap Send to confirm.
To restore starter:
- Tap Fuel/Power Remote Control.
- Select Restore
- Enter the App password then tap Send to confirm.
Note: For safety reason, remote engine cut will be disabled when the car is moving faster than 20km/h.
Position, Track History & Live Tracking
Positioning
- Open the Device List screen and tap the device to see the device location.
- This will display a live GPS display of your current vehicle location(s).
- Tap Detail to view details about the vehicle (including engine status, last time the vehicle was moved, IMEI & more).
Track History & Path Playback
- Open the Device List screen and tap the Playback icon under the device list to see the device track history.
- Select the time interval to playback.
- This will open a list of previous trips the vehicle took, including start/end times and locations, as well as total distance traveled.
- Tap any of these trips for a detailed GPS map displaying the full route the vehicle took.
- Use the slider at the top the skip to different parts of the playback. Map/satellite view and playback speed can be toggled with the buttons at the top right.
Configuring Geo-fences
Geo-fence Intro
Geo-fences are GPS zones you can designate on a map. When your vehicle enters
and/or exits the geofence, you can set the device to send a notification alert
to your account.
Creating a Geo-fence
- Tap List to open the Device List screen.
- Select the vehicle(s) you want the geo-fence to apply to. Tap the icon then tap Geo-Fence. A list will appear showing all created geo-fences. Tap + to make a new one.
- A GPS map will appear. Navigate and place the geo-fence, then adjust its size using the slider.
- After setting the geofence zone, tap [ Edit ] to enter a name for the geo-fence.
- Tap Save to confirm.
- Select one or both of the Alert settings (Enter/Exit ). to receive notifications on vehicle geo-fence enter/exit.
NOTE: Using the app, you can only create circular geo-fences. More
precise geo-fences with individually drawn lines can be created from the
website (www.tracksolid.com). Some features of
the website are still under development; it will be more powerful in the later
version.
Camera Remote Access
Real-time Video Overview
- Open the Home screen and tap Remote Video.
- Tap the left camera icon at the top right to start live viewing the camera in real-time. This may take a few seconds to load, depending on your mobile network.
- From here, several actions & options are available:
Switch camera: Tap the camera icon at the top right (overlayed onto the video) to switch between the road and driver cameras.- Playback: Tap the video screen to bring up a time bar. Scroll through to play recorded footage.
- Mute: Mute/unmute the camera’s microphone.
- Screenshot: Saves a snapshot from the current camera display.
- Two-way talk: Hold to talk through the camera with your phone.
- Record: Record a clip from the camera display.
- Fullscreen: Toggle portrait/landscape display modes.
Remote Picture
- Open the Home screen and tap Remote Picture.
- In this menu, you can look through all snapshots taken from the camera. Tap any of them to display them full-screen.
- To save a snapshot to the camera, open an image and tap Save to album.
- To take a new snapshot, tap the camera icon at the top right.
- To share an image, tap Share at the bottom right, then select the snapshot(s) to share and tap OK.
Remote Video
- Open the Home screen and tap Remote Video.
- In this menu, you can look through all video recordings taken from the camera. Tap any of them to download, then tap again to play.
- To save a new recording, tap the right camera icon at the top right. Select the Internal or External Camera to record and a length of time, then tap OK.
- To share an image, tap Share at the bottom right, then select the videos) to share and tap OK
Media Center & Backup
Local Media Library
- Open the Device List menu.
- Tap the icon on the device you want to set then tap Camera.
- Tap the Media on the title bar on top to select local or remote Media Center.
- In this menu, you can view, share or delete any saved snapshots & videos
Backup via Media Sync
- In the Media Centre menu, tap the SD card icon on the top right of the screen to connect the mobile to the camera’s WiFi hotspot. To connect, the camera must be powered on with the mobile nearby. Ensure that the blue GSM indicator on the camera is solid blue (not flashing).
- If the WiFi hotspot is connected successfully, the folders on the Micro SD card will be shown. If not tap the Go to SD card button to connect manually.
- Select Photo or Video.
- Select the camera to backup
NOTE: The username of the hot spot is the IMEI. The password is the last
8 digits of the IMEI. These can both be found on the camera or on the
App.
Backup via Micro SD
Remove the Micro SD card from the camera. Insert the card into a memory card
reader connected to PC. Then copy the files from the card reader to the PC
for backup.
WiFi Hotspot
When the WiFi hotspot is ON, you can also connect to this WiFi hotspot to
access the internet. The WiFi is actually using SIM card data. However, we DO
NOT recommend users use this SIM card to access the internet for other
devices as the data usage may exceed the SIM plan and no more remote
monitoring can be done.
Note: To turn the WiFi hotspot ON, you must connect to the Micro SD card
as described in section 3.7.2 even though you don’t want to backup the Micro
SD card. The WiFi hotspot will switch off when you quit the backup menu or
ignition is switched OFF.
Notifications
Notification History
- Open the main menu and press Notifications.
- This menu will display a complete history of the device’s notifications, including details on the time, date and type of notification. Scrolling to the bottom of the page will load older notifications.
Notification Events
The camera can alert the account of a wide list of events, which can be
toggled on/off from the app and website.
| • Collision/crash alert | • Night driving alert |
|---|---|
| • Vibration alert | • GPS blind zone alert |
| • Enter/exit geo-fence alert | • SOS alert |
| • Driver behavior alert | • Low battery alert |
| • Engine on/off alert | • Power off alert |
| • Overspeed alert | • Disassembly alert |
User Commands via SMS
User Commands
You can send SMS messages to the device to perform simple tasks. Refer to the
table below:
The default password is: 666666
| Command | Default Value | Command Format | Description |
|---|---|---|---|
| VERSION | – | VERSIONkpassword> | Check the firmware version |
| PARAM | – | PARAMkpassword> | Get IMEI, GPS upload interval |
and timezone information
STATUS| –| STATUS#
engine on/off status
PASSWORD| 666666| PASSWORD#
This product features a 2 year warranty.
**For more information, please visit:
www.securviewcctv.com
MDVR-J400 (Vehicle monitoring system)
vQ320**
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>