Sendx Audio FK702 SendX Wireless Audio Transmitter/Receiver User Guide
- June 6, 2024
- Sendx Audio
Table of Contents
Sendx Audio FK702 SendX Wireless Audio Transmitter/Receiver
Setup Instructions
-
Plug charging base into wall socket and place SendXFobs on base to charge. It takes up to two hours to fully charge. The Battery indicator light on the SendXFob will be solid red when charging and then will turn off once it is fully charged.
-
Connect transmitter to TV and plug USB into power source on TV (Alternative: Plug USB into separate power source)
-
Adjust TV audio settings to enable audio out for the port you have plugged the transmitter into. You may have the option to mute the sound coming from the internal TV speakers or keep both on. We recommend keeping both on if you have the option so you don’t have to switch back and forth. For SendXDigital, you will need to select the PCM 2-channel option only if it is shown as an option.
-
Turn on the TV and select something to watch with continuous audio.
-
Turn on the SendXfobs once they are charged. Ensure that the LED light for the “Mode” on the SendXFob is set to receive mode (“Recv”). You can depress the Mode button to set the SendXFob to receive mode if it is in Send mode. Press the Bond button twice to search for the audio signal being transmitted from the TV.
-
Turn the SendXFob volume down to the lowest level and plug your earbuds, headphones or powered speakers into the 3.5mm port. Gradually increase the SendXFob volume to a comfortable listening level.
-
Once you’ve confirmed you are listening to audio, you can press and hold the Bond button for 2 seconds so that it remembers the transmitter channel.
The LED light above the Bond button will turn green. -
That’s it! Set up is complete. The next time you want to listen to HD wireless audio with your favorite earbuds, headphones or powered speakers, you can just turn on the TV and SendXFob and plug it in. Enjoy!
SKAA® RECEIVER USER’S GUIDE
Each SKAA receiver uses a Green List to remember your favourite audio sources (SKAA transmitters). A Green glowing Indicator on your receiver means you are listening to a favourite, or hunting for one. You can also explore to find new transmitters—an Amber Indicator means you are exploring for transmitters which are not on your Green List. The Bond Button on your receiver lets you select which audio source (SKAA transmitter) you’re listening to.
Essentials
More Commands
QUESTIONS AND ANSWERS
Troubleshooting tips
Be sure the receiver is set to receive mode if you are unable to receive an audio signal. Depress the send/receive button to switch between send and receive. The SKAA connection can be re-set by depressing the bond pair button 6 times. Repeat the set-up instructions to pair the receiver with the transmitter. The USB plug for the transmitter may need to be plugged directly into a USB wall outlet if there is excessive interference noted while it is plugged into the transmitting device for power (i.e. USB port in TV Set). For digital transmitters, the TV should be configured for PCM audio transmission.
Product Specifications
- Range – 100 Feet
- Average Charge Time – 2 Hours
- Average Playback Time – 10 Hours
Safety Warnings
WARNING – Important Safety Instructions
Read through all instructions and safety warnings.
- Do not use this product near water.
- Do not install the product near any heat sources such as radiators, heat registers, stoves or other apparatus that product heat.
- Protect the power cord from being walked on or pinched, particularly at plugs and the point where they exit the apparatus.
- Unplug the product during lightning storms or when unused for long periods of time.
- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- Do not exposure this product to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed near the product.
- Do not expose the product to excessive heat such as sunshine, fire or the like.
- Open flame sources, such as lighted candles, should NOT be placed near the product.
- This product is only designed for indoor use.
Limited One-Year Warranty
This warranty covers any defect in materials and workmanship. The original
purchaser of the SendX product is covered under thzese warranty provisions
only if the product was purchased directly from SendXAudio by the original
purchaser. The warranty is not transferable. The warranty will be void if the
product was used for any purpose other than its intended purpose or the
malfunction was caused by negligence of installation or use by the purchaser.
Normal wear and tear, heat and water damage are not covered by this warranty.
The SKAA Compatible Badge found on the Product certifies that this Product has
been tested and is fully compliant with all of the requirements of the SKAA
Standard and has been granted SKAA Certification. This Product will work
seamlessly with other products in the SKAA ecosystem of audio transmitting and
receiving devices. For more information on the SKAA Standard, please visit
www.SKAA.com. The SKAA® name as well as its associated
marks, logos and icons are trademarks or registered trademarks of Eleven
Engineering Incorporated.
FCC Requirement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. This device and its
antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 centimeters between the radiator and your body.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
This equipment complies with IC RSS_102 radiation exposure limits set forth
for any uncontrolled environment. This equipment should be installed and
operated with minimum distance of 20 centimeters between the radiator and your
body.