Brio 500 Series 2 Stage Tri Temp Bottleless Water Cooler User Manual
- May 15, 2024
- BRIO
Table of Contents
Brio 500 Series 2 Stage Tri Temp Bottleless Water Cooler
“`html
Specifications
- Model No.: CLPOU520UVF2BLK
- Dimensions:
- Height: 105.1 cm (41.4 in.)
- Width: 31.1 cm (12.2 in.)
- Depth: 36.3 cm (14.3 in.)
Product Usage Instructions
Safety Information
Before assembling, installing, and operating the dispenser, make
sure to read the entire guide to reduce the risk of injury and
property damage.
Intended Use
This appliance is not intended for use by individuals with
reduced physical, sensory, or mental capabilities unless supervised
by someone responsible for their safety.
Product Features
The dispenser features hot water, room temperature water, and
cold water buttons, along with tap outlets for each water type, an
indicator panel, drip tray, and filter cabinet with carbon block
and sediment filters.
Installation
-
Determine Installation Location
-
Place the dispenser upright on a hard and level surface near a
grounded wall outlet. -
Position the back of the dispenser at least 20 cm (8 in.) away
from a wall to allow free airflow. -
Do NOT plug in the power cord until installation is
complete. -
Connect to the Cold Water Supply CAUTION: Connect the water line to a cold water
supply line to prevent damage to the filters. Using hot water can
severely damage the filters.
FAQ
Q: How do I know when to replace the filters?
A: The filter indicator light will blink red when it’s time to
replace the filters. Once expired, the light will stay on, and the
unit will beep to alert you to change them immediately.
Q: What does the blinking UV indicator light mean?
A: The blinking UV indicator light indicates that the
self-cleaning UV system is active.
“`
Point of Use Water Dispenser Setup Manual
Model No.: CLPOU520UVF2BLK
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 4 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 4
Indicator Panel Description . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Materials Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 Determine Installation Location. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Connect to the Cold Water Supply . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Flush
the Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Install the Filters and Complete the Installation . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operation .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Turn
the Dispenser On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Dispense
Cold Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Dispense
Hot Water and Activate Child Safety Lock. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . 9 Troubleshooting . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .10 Cleaning and Maintenance . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .10 Clean the Dispenser . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .11 Filter Replacement Schedule. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 12 Replace the Filters . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 12 Filter Specifications . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 13 Care and Maintenance . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 13 Warranty. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .14
2
Safety Information
WARNING: To reduce risk of injury and property damage, you must read this
entire guide before assembling, installing and operating the dispenser.
WARNING: This product dispenses water at very high temperatures. Failure to
use properly can cause personal injury. When operating this dispenser, always
exercise basic safety precautions, including the following: · Prior to use,
this dispenser must be properly assembled and installed in accordance with
this manual. · For indoor use only. Keep the water dispenser in a dry place
away from direct sunlight. Do NOT use outdoors. · Install and use only on a
hard, flat and level surface. · Do NOT place the water dispenser in an
enclosed space or cabinet. · Do NOT operate the dispenser in the presence of
explosive fumes. · Use only properly grounded outlets. · Do not use an
extension cord. · Always grasp the plug and pull straight out from the outlet.
Never unplug by pulling on the power cord. · Do NOT use the dispenser if the
cord becomes frayed or otherwise damaged. If the supply cord is damaged, it
must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard. · To protect against electric shock, do
NOT immerse cord, plug, or any other part of the dispenser in water or other
liquids. · Ensure the water dispenser is unplugged prior to cleaning. · Never
allow children to dispense hot water without proper and direct supervision.
Unplug the unit to prevent unsupervised use by children. · Service should be
performed only by a certified technician. · The appliance must not be cleaned
by a water jet and is not suitable for installation in an area where a water
jet could be used.
WARNING: Keep ventilation openings, in the appliance enclosure or in the
built-in structure, clear of obstruction. WARNING: Do not use mechanical
devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer. · This appliance should work under
environment of temperatures from 4°C~40°C (39°F~104°F) and humidity 90%. ·
Never turn the machine upside down or lean it more than 45°. · After turning
the dispenser off, allow the dispenser to sit idle for 3 minutes before
turning on again.
WARNING: UV light source. Disconnect the electrical supply to the UV radiation
BEFORE opening cover. · UV-LED lamp must be repaired by manufacturer only. ·
UV-LED lamp model no. YB09-950-022, rated DC 24V, 0.17W±20%. · Disposal of the
UV-LED lamp must be done in accordance with local laws and regulations.
3
Intended Use
This appliance is intended to be used in household and similar applications
such as: · Staff kitchen areas in shops, offices and other working
environments · Farm houses · Hotels, motels, and other residential-type
environments · Bed-and-breakfast-type environments · Catering and similar non-
retail applications
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Product Features
Part
1 2 3 4 5 6 7 8 9 10
Description
Hot water button Room temperature water button Cold water button Indicator
panel Cold water tap Room temperature water tap Hot water tap Drip tray Filter
cabinet Carbon block filter
Part
11 12 13 14 15 16 17 18 19
Description
Sediment filter Night light Filter reset switch Night light switch Cold water
switch Hot water switch Condenser Drain outlet Water inlet
4
Indicator Panel Description
1. Power / UV indicator light – When illuminated, indicates that the
dispenser is on. When blinking, indicates that the self-cleaning UV system is
on.
2. Hot water indicator light When illuminated, indicates that the dispenser
is heating water.
3. Cold water indicator light When illuminated, indicates that the
dispenser is cooling water.
4. Filter indicator light – This light will begin blinking red to notify you
that its time to replace your filters. Once the filters have expired, the red
light will remain steadily illuminated, and the unit will beep to alert you
that the filters should be changed immediately.
Product Dimensions
Height
105.1 cm (41.4 in.)
Width
31.1 cm (12.2 in.)
Depth
36.3 cm (14.3 in.)
Package Contents
C A
1
2
3
4
F
B
D
E
G
Part Description
A Filter flushing tube B Shut-off valve tube (7 ft.) C Filter housing (for
filter flushing) D Sediment filter E Carbon block filter F Feed water adapter
(with extra nut) G Plumber’s tape
Quantity
1 1 1 1 1 1 1
Materials Needed
Wrench 5
Installation
1. Determine Installation Location
A. Place the dispenser upright. B. Locate the dispenser on a hard and level
surface in a cool shaded location near a grounded wall outlet.
NOTICE: Do NOT plug in the power cord until the entire installation section is
completed.
C. Position the back of the dispenser no closer than 20 cm (8 in.) from a wall
and permit free airflow between the wall and water dispenser.
2. Connect to the Cold Water Supply
CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water
supply to the unit MUST be from the COLD WATER LINE. Using HOT WATER will
severely damage your filters.
A. Turn off and then disconnect the current cold water supply line.
B. Connect the feed water adapter (F) to the cold water supply line.
F
C. Connect the cold water supply line on top of the feed water adapter (F).
NOTE: An extra adapter nut is included on top of the feed water adapter (F) to
attach to a 3/8 in. or 1/2 in. feed plumbing line.
D. Insert the shut-off valve with tube (B) straight into the quick connector
piece
of the feed water adapter (F).
F B
6
E. Gently tug on the tube (B) to ensure a secure connection with the feed
water
adapter (F).
F B
3. Flush the Filters
IMPORTANT: Follow this procedure every time you replace your filters.
IMPORTANT: Ensure the water supply is off before you begin.
A. Connect a filter (D) to the filter housing (C)
C
by twisting the filter (D) clockwise.
D
B. Connect the tip of the shut-off valve tube (B)
to the left side of the filter housing (C).
C. Connect the filter flushing tube (A) to the
B
right side of the filter housing (C) and lay the
open end of the filter flushing tube (A) over a sink or receptacle to collect water.
C A
D. Flush each filter for a minimum of
5 minutes. The recommended rate is
1.5-3 gallons of water (about 10 minutes)
B
or until the water is clear in appearance.
E. Shut off the valve at the water source and remove the filter housing from the tube (B).
7
4. Install the Filters and Complete the Installation
A. After flushing, twist each filter (D) clockwise into the filter housings
located inside the dispenser cabinet. The sediment filter goes on the left,
the carbon block filter on the right.
D
B. Remove the safety plug from the water inlet hole on the back of the
dispenser by pushing in the inlet hole collar and then gently pulling out the
plug.
C. Connect the tip of the shut-off valve tube (B) into the water inlet hole on
the back of the dispenser. Then turn on the main water supply and ensure the
valve in the tube (B) is on.
B
8
Operation
IMPORTANT: This unit has been tested and sanitized prior to packing and
shipping. During transit, dust and odors can accumulate in the tank and lines.
Dispense and dispose at least one quart of water prior to drinking any water.
Turn the Dispenser On/Off
IMPORTANT: Before you activate the hot and cold switches, ensure water has
filled the tanks inside the dispenser in order to prevent dry heating.
1. Plug in the dispenser. 1. Run water through the cold and hot water taps
until water begins to dispense. 2. To power on the cooling system, flip the
cooling switch to the On position. 3. To power on the heating system, flip the
heating switch to the On position.
Dispense Cold Water
NOTE: Water will take approximately 1 hour after plugging in and turning on to
become completely chilled. The cooling light will turn off once the water has
been fully chilled.
1. Place a drinking glass or container under the cold water faucet and press
the cold water button to dispense cold water.
2. Release when your container is full.
Dispense Hot Water and Activate Child Safety Lock
CAUTION: This unit dispenses water at temperatures that can cause severe
burns. Avoid direct contact with hot water. Keep children and pets away from
the unit while dispensing. Never allow children to dispense hot water without
proper and direct supervision. Disable the heating feature by switching the
heating convenience switch to the Off position.
NOTE: Water will take approximately 15-20 minutes after plugging in and
turning on to reach its hottest temperature. The heating light will turn off
once the water has been fully heated.
1. This water dispenser is equipped with a child safety feature in order to
prevent inadvertent dispensing. To enable dispensing of hot water, place a cup
or container under the hot water faucet. Slide the red lock button on the hot
water button to the left. While holding the red button, press the hot water
button and dispense hot water.
2. Release the red lock button and hot water button once your container is
full.
9
Troubleshooting
Problem
The cold water is not cold.
The hot water is not hot. The night light is not working. The dispenser is
noisy.
There is water leakage. The machine is not dispensing water.
Solution
· It takes up to one hour after setup to dispense cold water.
· Make sure the power cord is properly connected to a working outlet.
· Make sure the back of the dispenser is at least 20 cm from a wall and there
is free airflow on all 20 cm sides of the dispenser.
· Make sure green power switch on back of dispenser is On.
· If water still isn’t cold, call customer service at +1
844-257-4103 for assistance.
· It takes 15-20 minutes after setup to dispense hot water.
· Make sure the power cord is properly connected to a working outlet.
· Make sure red power switch on back of dispenser is On.
· Make sure the power cord is properly connected to a working outlet
· Make sure the night light power switch on back of dispenser is On.
· Ensure the dispenser is located on a level surface.
· The heating tube may be generating a slight noise. This is normal.
If the 3 lights are flashing, a leak was detected.
· The pipe is not connected properly. Check all water connections and tubes to
ensure everything is connected properly.
· The water and PE pipes have burst. Replace the water and PE pipe.
· The dispenser has become too cold and the lines are blocked by ice. Turn the
cooling switch off for at least 4 hours to allow the water in the lines to
thaw.
Cleaning and Maintenance
Task
Sanitizing
Frequency
Every 3 months
Removing minerals deposits
Every 6 months
Instruction
Use a disinfectant, purchased separately, following directions from
manufacturer for proper amount to use. Use the Cleaning the Dispenser
directions when sanitizing.
Mix 4 liters water with 200g citric acid crystals, inject into the machine and
make sure the water can flow out of the hot water tap. Switch on the power and
allow it to heat for about 10 minutes. After 30 minutes, drain the liquid and
clean it with water, dispensing two or three times.
10
Clean the Dispenser
CAUTION: Before cleaning, make sure the power switch is in the O (off)
position and unplug the water dispenser.
IMPORTANT: This dispenser contains UV technology that will help keep your
dispenser clean. However, if you do need to clean your dispenser for any
reason, follow these steps:
1. Remove remaining water from reservoirs in the dispenser by dispensing from
the hot and
cold taps into a pitcher or bucket.
2. Remove the top cover (1), cold tank cover (2), and separator (3).
1
3. Rinse off the separator (3) in the sink and
wipe clean with a soft cloth.
2
3
4. Create a cleaning solution of 0.3 gallons
vinegar and 0.3 gallons hot tap water. Allow the cleaning solution to fill the
reservoir and sit for at least 10 minutes.
5. Place a large bucket beneath the drain outlet at the back of the
dispenser.
6. Remove the drain cover and drain the water. 7. Reinstall the drain cover,
separator, cold tank
cover, and top cover after draining. Ensure all water supply connections are
connected securely. 8. Plug the dispenser back into the outlet and turn on.
11
Filter Replacement Schedule
Filter Type
Model No.
Replacement Schedule
Sediment
NFMPP5M
6-12 months or 950 gallons
Carbon Block
NFMCTO5MS2 6-12 months or 950 gallons
Function
Performs a coarse filtration of original water. Removes mud, sand, iron, rust,
and suspensions, and impurities.
Reduces chlorine, taste and odor, lead and cysts.
Replace the Filters
1. When filter life is nearing its end, the filter indicator light (4),
located on the right side of the Indicator Panel, will blink red. When filter
life has expired, the filter indicator light will be steadily illuminated red
and the dispenser will beep to alert you that the filter needs to be changed.
2. Turn the valve on the shut-off valve tube until it’s in the OFF position, or perpendicular to the tube. NOTE: Alternatively, the shut-off valve located to the left of the sediment filter inside the cabinet can be turned to the OFF position instead.
3. Remove the expired filters from their filter housings by twisting counterclockwise. To install new filters, insert into filter housing and twist clockwise.
4. Open the valve on the shut-off valve tube until it’s in the ON position, or parallel to the tube.
12
5. Press and hold the filter reset switch (13), located on the back of the dispenser, until the filter indicator light turns off.
6. To flush filters, dispense cold water from cold water tap (5) for approximately 2 minutes.
Filter Reset Switch
Cold Water Tap
2 mins
Filter Specifications
Sediment Filter (Sediment, Dirt, and Rust Removal)
Filter Capacity Flow Rate Suggested PSI Temperature
950 Gallons 0.8 GPM 14.5 – 58 psi 33 – 100 °F
Carbon Block Filter (Taste and Impurity Removal)
Filter Capacity Flow Rate Suggested PSI Temperature
950 Gallons 0.8 GPM 14.5 – 58 psi 33 – 100 °F
Care and Maintenance
· Keep this dispenser in a dry and cool place and avoid direct sunshine.
· Ensure the back of the dispenser is at least 20 cm (8 in.) away from the
wall.
· Never put the dispenser on paper or foam, which may store water and then
cause creepage. Never put anything flammable beside this machine.
· Do not use the dispenser outdoors or in a place that can be splashed by
water.
· If the dispenser is not in use for longer than a 24-hour period, turn off
the heating switch or the refrigerating switch to save power and drain any
remaining water.
· If the water supply is cut off, shut off the water supply and turn the
dispenser off. When the water supply is back on, re-open the water supply to
the dispenser, turn the dispenser on, and allow the dispenser to run in order
to discharge sediment.
13
Warranty
Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers
(the “Product”), and to no other person, that if the Product is assembled and
operated in accordance with the printed instructions accompanying it, then for
a period of one (1) year from the date of purchase, all parts in the Product
shall be free from defects in material and workmanship. This Limited Warranty
shall be limited to repair or replacement of parts, which prove defective
under normal use and service and which Vendor shall determine in its
reasonable discretion upon examination to be defective. To take advantage of
this Limited Warranty, please follow these steps: 1.Please retain your sales
slip or invoice, as Vendor may require reasonable proof of your date of
purchase. 2.Contact Vendor’s Customer Service Department using the contact
information listed below. 3.Return parts to Vendor, per Vendor’s instructions,
at your cost and expense. 4.Upon receipt by Vendor, Vendor shall advise you in
writing whether a defect covered by this Limited Warranty exists
in any returned part and whether your claim has been approved or denied.
5.Upon Vendor’s approval of your claim, Vendor will replace such defective
part without charge to you. WHAT THIS LIMITED WARRANTY DOES NOT COVER: This
Limited Warranty does not cover any failures or operating difficulties of the
Product due to accident, abuse, misuse, alteration, misapplication, improper
installation or improper maintenance or service by you or any third party, or
failure to perform normal and routine maintenance on the Product, as set out
in the User’s Manual. In addition, this Limited Warranty does not cover
damages to the finish, such as scratches, dents, discoloration or rust after
purchase. This Limited Warranty is the only express warranty given on the
Product and is in lieu of all other express warranties. Vendor disclaims all
warranties for products that are purchased from seller other than authorized
retailers or distributors. THIS LIMITED WARRANTY RESTRICTS THE DURATION OF ANY
AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPIED WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO THE ONE (1) YEAR
TERM OF THIS LIMITED WARRANTY. UPON THE EXPIRATION OF THE ONE (1) YEAR TERM OF
THIS LIMITED WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, THE PRODUCT BEING THUS SOLD AS-IS, WITH ALL
FAULTS. FURTHER, VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY
THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES. OTHER THAN THIS LIMITED WARRANTY, THERE ARE NO WARRANTIES WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. Vendor assumes no
responsibility for any defects caused by third parties. This Limited Warranty
gives you specific legal rights, and you may have other rights which vary from
state to state. State law may also override statements in this Limited
Warranty regarding the restriction on the duration of implied warranties. Some
jurisdictions do not allow exclusion or limitation of special, incidental or
consequential damages, or limitations on how long a warranty lasts, so the
above exclusion and limitations may not apply to you.
14
15
©2024 Brio Water Technology, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>