NextCentury RR4 Remote Reader User Guide

June 6, 2024
NextCentury

RR4
Quick Start Guide

Welcome to your new Remote Reader. The RR4 is an advanced meter readisolu-on that provides a high visibility remote display of one or two u-limiters. Seng up and installed on the RR4 Remote Reader is quick and easy. A that includes built-in wireless AMR support is also available (RR4-TR).

Packaging Contents

A) RR4 Remote Reader
B) Moun-ng Plate
C) Sheetrock Anchors
D) Wall Mount Screws #6-20
E) Box Mount Screws #6-32
F) Wire Security Assembly
G) Ac-VA-on Magnet (one per case)

Important

During install-on, you will disconnect the Remote Reader from the Moun-ng Plate. It is not necessary to open the Remote Reader. The Remote Reader is a sealed, water–tight design, and should only be opened to replace the battery (10-year approximate battery life).

Addi$onal Resources

http://products.nextcenturymeters.com/rr4

For a full install-on guide, spec sheets, and addi-on resources, please visit: products.nextcenturymeters.com/rr4
Contact Information
Phone: 844.538.8203
Email: support@nextcenturymeters.com

Installation

NextCentury RR4 Remote Reader - fig 2

  1. Pull Down Security Tab to Remove Remote Reader from Mounting Plate
  2. Secure the Mounting Plate and Connect Meter(s)
  3. Connect Remote Reader to Mounting Plate Then Lock Security Tab

Installation Steps

  1. Disconnect the Remote Reader from the Moun.ng Plate. Remember to first pull down on the Moun.ng Plate Security Tab.
  2. Install the Moun.ng Plate using the anchors and #6-20 screws, or use the #6-32 screws to install on a single gang wall box.
  3. Connect the wire output from one or two meters to the Remote Reader Moun.ng Plate (wiring instruc.ons on the other side of this guide).
  4. The Remote Reader ships with a default configura. on to read a single pulse-type meter. To program the Remote Reader for other configura. ons use the NCSS Mobile App’s Direct Connect tool.
  5. Test the meter connec.on:
    – For pulse meters, ensure the pulse
    -count increments when a pulse is sent from the connected meter.
    – For encoder meters, ensure the proper read is displayed. It may be necessary to tap the display or swipe a magnet to get the latest encoder meter read.

Wiring Guide

Possible Configura7ons
– 1x Pulse Meter – Default (Meter 1 Port)
– 1x Encoder Meter (Meter 1 Port)
– 2x Pulse Meters (Meter 1 & 2 Ports)
– 2x Encoder Meters (Meter 1 & 2 Ports)
– 1x Encoder & 1x Pulse (Meter 1 & 2 Ports)
– 1x Pulse & 1x Encoder (Meter 1 & 2 Ports)
– 1x Pulse with Pulse Out (Meter 1 & 2 Ports)

Wiring Guide
An interac7ve Wiring Guide is also available through the NextCentury Mobile App (Android and iOS Support).

Dual Meter+™ Technology
Meter+™ Technology has been developed to allow a single device to connect to virtually all modern meter outputs. These include a variety of different pulse- out meters as well as encoded output meters. Meter+™ Technology supports Neptune, Sensus, GWF, and Elster/AMCO 3-wire protocols. Simply wire the meter and prograthe Remote Reader with the applicable configura7on. The Remote Reader includes two Meter+™ Technology ports, allowing for a large variety of different configura7ons.

Serial Number
The Serial Number is located on the face of the Remote Reader. This iden7fica7on number always ends with a “0.” When communica7ng with the NextCentury Web PlaWorm through a Cellular Gateway, each meter is assigned a unique Transceiver Serial Number. The Serial Number for Meter 1 will end with a “1” and the serial number for Meter 2 will end with a “2.”

NextCentury RR4 Remote Reader - fig 4

 Direct Connect

Note: the DC301 wireless programmer is not required for configuring this model.

Programming

Configuring and testing the Remote Reader is completed using the NCSS Mobile App. The Mobile App’s Direct Connect tool facilitates communication with your Remote
Reader. The Mobile App allows simple in-field programming and configuraMon and does not require an active Internet connecMon.

Mobile App Download

http://products.nextcenturymeters.com/mobile?platform=ios&device=rr301

http://products.nextcenturymeters.com/mobile?platform=android&device=rr301

Additional Products
– RR4-TR: Remote Reader with an Integrated NextCentury Transceiver
– GW4: Cellular Gateway
– RE4: Wireless Network Repeater
– Pre-Programming: Equipment configured and ready for install
For more, visit: www.nextcenturymeters.com or contact sales@nextcenturymeters.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals