Shenzhen So Playful Technology Snapods TWS Earbuds with MagSafe User Manual

Shenzhen So Playful Technology Snapods TWS Earbuds with MagSafe User

Manual

Please read this manual carefully before using this product and keep it

properly

Power On/Off

1. The earbuds will automatically turn on when taken out from the charging case and turn off when ppt in.

2. .In the power-off mode, long press the touch area to power on. In the disconnected mode, long press the touch area to power off.

Accessory description

Attention

1. Please do not listen to the audio at a high volume for a long time.
2. Power off: put the left and right earbuds into the case to charge and turn off. Disconnected: long press touch.
3. Please do not let children or pets play with this product or its packaging and accessories, so as not to swallow.
4. Please stay away from items that are easily affected by magnetic fields, such as pacemakers, especially medical supplies.
5. Wireless Charging: please adjust the equipment to the appropriate position of the charging board.
6. Please do not put the product in the water to avoid problems such as short circuit, fire hazard and bulge.
7. The earbuds will automatically turn on and connect to the device if the charging case run out of electricity.

Product parameters

Brand: iSwift Model number: Snapods Bluetooth version: 5.2 Charging case charging port: type c Earbuds charging time: 1.5 hours Charging case charging time: 2 hours Bluetooth distance: ‘.10m(in a barrier-free and undisturbed environment) Frequency response range: 20hz-20khz Listening time: About 5 hours (medium volume) Earbuds battery capacity: 35mAh Charging case batterylcapacity: 700mAh Earbud charging input: MAX=DC5V 35mA Charging case charging input: MAX=DC5V 500mA Earbuds current when playing music: AVG=7mA Charging case standby power consumption: 20UA

Instructions

1. Power on: the earbuds will be automatically turned on after taken out from the case. Long press the touch area if in off state.
2. Power off: put the earbuds into the case to charge and turn off. Long press the touch area to disconnect .It will shut down after 3 mins if not connected.
3. Pairing status: when there’ s no pairing record, the earbuds go directly into pairing state / when there’ s a pairing record, the earbud will automatically connect to the device and it will go back to pairing mode if failed to connect.
4. Turn on/Off Siri speech recognition: hit the left and right earbud 3 times
5. Previous/ next: long press left earbud/long press right earbud
6. Answer/ hang up the phone: touch once/ touch twice (works for either side)
7. Refuse an incoming call: long press the earbud (works for either side)
8. Play and pause: touch the earbuds twice quickly within 0.5s(works for eitherside)
9. Reset: click for 5 consecutive times when there’ s no connection. Restart the earbuds after shutting down. (take them from the charging case or long press the touch area). Reset complete when two earbuds are connected. 1
10. Volume+/Volume-: touch the right earbud once/touch the left earbud once. It doesn’t work if use in single earbud.
11. Android devices need to turn on the synchronization switch to make the earbuds volume can be synchronized with the phone volume.

When charging the charging case

LEDl ll;ishes M33% battery,
Wlien the llattery is 66%, 11,e LEDl Is always on and the LED2 !lashes.
Wlien the battery is more than 66%, the LEDl LE02 are alway on, the
LE03 Hashes until fully charged, then it stops 11″”‘1ine ;i nd ;ilway,. on .
At 100% battery, the L£D1 LEOO LEOO are alwap on until you unplug the [IQW11re<irdorle;ivettiewireltlS’ldi;i’i’,!r.

When charging the earbuds

When the battery is 100%, the LED1 LED2 LED3 will turn on about 4s and then turn off. When the battery is 66%, the LED1 LED2 turn on about 4s and then turn off When the battery is 33%, the LED1 will turn on about 4S and then turn off. When the voltage is lower than 3.3V, the LED1 flashes continuously and rapidly, indicating that the charging case should be recharged in time as the electricity is too low.1

LED indicator

Power on: the red and blue lights are on for 1 second at the same time. Turn off: the red light is on for 1 second. Standby(no device connectiom): both earbuds flash blue light quickly Standby(connected to a device): no flashing lights on two earbuds. During the call: When the incoming call is alerted, the main earbud flashes twice in 3seconds; no lights are on during the call. Charging: the red light is always on. Charging completed: the blue light turns off for 10 seconds, and the light is no longer on. Low voltage alarm: a light flashes in the charging case Power-on reconnection status (connected): no light Earbuds unpaired: red and blue light will flash Reset completed: touch 5 times continuously, the red and blue lights will be on together, and then it will be automatically shut down

Cue tone

Guarantee card

rilame:
Telephone:
Mailbox:
Postalrnde:
Address:
Equipment model:
Oateof purchase:

Copyright Statement

Shenzhen So Playful Technology Co., Ltd. All Rights Reserved.

Company intonation

Shenzhen So Playful Technology Co., Ltd. Address: RM1207, BLK C, Zhantao Technology BLDG, Minzhi Avenue, Minzhi ST, Longhua DIST, Shenzhen, China Email : support@iswift.us Website: www.iswift.us Made in China

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>